Yamaha YSP-2200 Manual

Yamaha Soundbar YSP-2200

Læs gratis den danske manual til Yamaha YSP-2200 (3 sider) i kategorien Soundbar. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Yamaha YSP-2200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

This Quick Reference Guide explains steps to connect TV and Blu-ray disc player to this unit and start playback.

Make sure to read “CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.” on Safety and Accessory Information first.

■Prepare the remote control

Install batteries in the remote control. Operation range

YSP-2200 (YSP-CU2200 + NS-SWP600)

Quick Reference Guide English

UCTABGLV

Necessary items for this manual

Supplied items

Optional items

*This guide explains how to connect TV and Blu-ray disc player with HDMI input/output jacks.

Refer to Safety and Accessory Information about other supplied accessories.

TV Blu-ray disc player HDMI cable (×2)

Center unit and Subwoofer

(×1)

Remote

control (×1)

Cardboard microphone stand

(×1)

IntelliBeam microphone (×1)

IR Flasher (×1) Stands for

subwoofer (×4)

Speaker cable (×1) Non-skid pad for the center unit

(×4)

Battery (×2)

(AA, R6, UM-3)

Optical cable (×1) Video pin cable (×1) Demonstration DVD (×1)

Press U.

Battery × 2

(AA, R6, UM-3)

Remove the transparent

sheet before using the

remote control.

Within 6 m (20 ft)

Installation Connection Settings Playback

Install YSP-2200

●Install this unit in the exact center of the wall when it is measured from the left and right corners.

●Install this unit as close to the exact front of your normal listening position as possible.

Some of your TV have sensors such as motion sensor, or signal

transmitter for 3D glasses in front. Installing the center unit may

interrupts the sensors or signal transmitter functioning. Set the center

unit away from your TV, or install it in your rack.

Center unit

Install this unit in the center of the left and right walls.

Listening position (such as sofa, etc.) should be located at the

front of the unit.

The distance between listening position and the unit should be

more than 1.8 m (5.9 ft).

Subwoofer

Install the subwoofer as close to the center unit as possible for a better

unit of sounds.

When the center unit straddles the stands of your TV

Attach the stands to the subwoofer

Install the subwoofer with the supplied stands. Horizontal placement is

convenient for installing the center of a rack, and vertical placement is

convenient for installing the side of a rack.

When the center unit hides the remote

control sensor of your TV

Remove the center unit legs

Use IR Flasher (supplied)

The unit receives the signal from the remote control of your TV in front,

and transmits to your TV by IR Flasher (supplied). Remove the backing

paper on the tip of LED part of IR Flasher, and attach it to the remote

control sensor of your TV or the area close to the remote control sensor

of your TV on the rear panel of center unit as shown. Connect the plug

to the IR output jack of the unit.

When using IR Flasher, direct the remote control of your TV to the

center unit.

This function is valid even in the standby mode.

This function may not activate with some TVs.

Center unit

Subwoofer

The graduation

(from 0 to 10)

Adjustable range:

28.5 mm to 38.5 mm

(1-1/8 in to 1-1/2 in)

Turning the stands to left makes the unit higher.

Confirm the graduation of each stand to make

each stand the same height.

Horizontal placement Vertical placement

3 Push the whole leg to the center of the bottom as shown in the

illustration while laying the hook to the same direction and

remove it.

2 Remove the outside part of

the leg.

1 Turn the leg furthermore to

the left.

4 Attach the 4 non-skid pads (supplied) to the corners on the bottom of

the center unit. (The illustration below is one of the examples for

attaching the non-skid pads.)

Non-skid pad

IR Flasher (supplied)

Remote control

sensor of your TV

yHint

Installation Connection Settings Playback

Connect your TV and Blu-ray disc player

●Do not connect the power cable until all connections are completed.

●Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or terminal.

For the cable connection, follow the orders below.

Refer to Owner’s Manual on the page 15 when connecting your game console etc.

Audio return channel (ARC) supported TV

Connect HDMI cable to audio return channel supported terminal (the terminal with “ARC” indicated) on TV. In this case, you do not need

to connect optical cable.

Activate the HDMI control function of this unit so as to activate audio return channel (ARC). (See Owner’s Manual on the page 25.)

What is audio return channel (ARC)?

A function transmits digital audio signal output from TV to this unit through a HDMI cable. By this function, a digital audio pin cable to connect TV

and this unit is not needed.

HDMI cable

(optional)

Input the digital audio/video

signals of the Blu-ray disc

player to this unit.

HDMI cable

(optional)

The digital video of the Blu-

ray disc is reflected on TV.

Optical cable

(supplied)

Play back digital sounds of

TV on this unit. y

Video pin cable

(supplied)

To display the YSP-2200’s

setup menus on the TV.

123

INPUT1

HDMI INPUT

OPTICAL

OUTPUT

VIDEO AUDIOR L

HDMI

OUTPUT

Connect the center unit with the speaker cable (supplied) to the subwoofer.

Match the positive (+) of the subwoofer terminal to the positive (+) of the center

unit terminal, and the negative (-) of the subwoofer terminal to the negative (-) of

the center unit terminal.

Blu-ray disc player TV

1. Remove the cap

2. Check the

direction of the plug

Video signals

Audio signals

Subwoofer (supplied)

To AC wall outlet

Insert into the terminal on

the rear panel.

Twist and pull off the

insulation tube on the lead

wire.

(Example)

yHint

Installation Connection Settings Playback

Carry out AUTO SETUP for appropriate surround effects

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud

test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the

AUTO SETUP procedure is in progress.

Set the IntelliBeam microphone at your normal listening position.

Assemble the stand and place the IntelliBeam microphone on top of it horizontally as shown below.

Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be

when you are seated.

Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects obstruct the

path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the walls.

Press key on the remote control.

The power of this unit turns on.

Turn on the power of your TV and select YSP-2200 as the video input on your TV.

If you connected the video pin cable to TV Video In 1, as shown in the connection diagram, select video input 1 on the TV.

If no menu appears, make sure the video pin cable is connected correctly.

1 2 3 4 5

IntelliBeam microphone Upper limit

Center height of

this unit

Within 1 m (3.3 ft)

Listening

position

Cardboard

microphone stand

1.8 m (6.0 ft)

or more Lower limit

Center

line IntelliBeam

microphone

Cardboard

microphone

stand

YSP-

2200

Push [SETUP] to

begin SETUP MENU.

You can select the language described in the menu screen.

Press and hold SETUP key until the “LANGUAGE SETUP” menu appears. → Press U V/ key to

select the desired language and then press ENTER key. → Press SETUP key again.

yHint

Connect the supplied IntelliBeam microphone to the INTELLIBEAM jack on the front panel.

Make sure that your listening room is as quiet as possible.

For accurate measurement, turn off air conditioner or other devices that make noises.

Leave the room after the next procedure. The best setting may not be done if you are in the room. When leaving the room, bring this Quick

Reference Guide with you. The AUTO SETUP procedure takes about 3 minutes. Wait outside the room during the AUTO SETUP procedure.

To cancel the AUTO SETUP procedure after it is started, press RETURN key.

Press ENTER key to start the AUTO SETUP procedure and then leave the room within 10 seconds.

The screen changes as each measurement is carried out.

When the process is complete, a bell will sound and the

results will be displayed on the TV.

If “ENVIRONMENT CHECK : Failure” (“Error Code: E-1” etc.

is displayed in the front panel display) is displayed, see page

19 of the Owner’s Manual and run the measurement

process again.

The results displayed depend on the position of the YSP-

2200.

If you hear a buzzer sound and an error message

appears on the TV, look for a solution in “Error messages

for AUTO SETUP” on page 21 of the Owner’s Manual.

Then press RETURN key to run the measurement

process again.

Press ENTER key.

The measurement result is saved.

Disconnect the IntelliBeam microphone.

The initial screen appears. Keep the IntelliBeam microphone in a safe

place. The settings are automatically saved in the system memory.

IntelliBeam microphone (supplied)

Cardboard microphone stand

(supplied)

AUTO SETUPSETUP

(PREPARATION & CHECK)

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from SoundPro-

jector. The MIC should be set

at ear level when seated.

Measurement takes about 3min.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

S t a rt S e t u p ?

TV screen

Front panel display

yHint

Will begin in 10 sec.

Please leave the room.

---------

AUTO SETUP START

[RETURN]:Cancel

MEASUREMENT COMPLETE.

BEAM MODE :5Beam/Plus2

SUBWOOFER :Yes

[ENTER]:Save set-up.

[RETURN]:Do not save set-up.

XXXXXXXXSHOW RESULTXXXXXXXXXX

S t a r t i n 1 0 s e c

5 B e a m / S W F : R D Y

About 3

minutes

later

yHint

AUTO SETUP COMPLETE

Please remove the MIC

from Sound Projector

and the listening position.

S e t u p F i n i s h .

Installation Connection Settings Playback

Playing back

Play back the supplied demonstration DVD, and confirm the exact connection and settings.

Then, have fun for playback!

For detailed operation, refer to the Owner’s Manual on the supplied CD-ROM.

Press key to turn on this unit.

Turn on your TV and Blu-ray disc player connected to this

unit.

Press HDMI1-3 to select the Blu-ray disc player as the input

source.

Press TV key to select the TV as the input source.

Set the input source of TV to HDMI input 1.

Play back the supplied demonstration DVD.

Refer to “Using the supplied demonstration DVD”. (Refer to Safety and Accessory

Information.)

Press VOLUME +/- key to adjust the volume.

Use TV remote control to mute the sound from TV.

Press SURROUND key and then the CINEMA DSP keys to

set your sound preferences.

When this unit does not play back, check the following

The connection between this unit and Blu-ray disc player.

The audio output settings of Blu-ray disc player is set to digital sound output.

The input of TV is selected exactly.

H D M I 1

Input source name

yHint

HDMI control function

You can use the TV remote control to operate this unit if your TV supports the HDMI control function. See the page 25 of Owner’s Manual about

settings.

yHint

Produkt Specifikationer

Mærke:	Yamaha
Kategori:	Soundbar
Model:	YSP-2200
Type:	Hjemmebiograf højttalere
Tænd-/slukkontakt:	Ja
Produktfarve:	Sort
Udgangseffekt (RMS):	132 W
Strømforbrug (standby):	0.5 W
Volumenkontrol:	Digital
Lyd-output kanaler:	7.1 kanaler
LED-indikatorer:	Ja
Fjernbetjent:	Ja
Lyd (L, R) indgang:	1
Diskant diameter:	28 mm
Woofer diameter:	100 mm
Mid-range driver diameter:	28 mm
Subwoofer RMS-effekt:	100 W
Satellithøjttalere RMS-effekt:	32 W
Centerhøjttaler dimensioner (BxDxH):	944 x 145 x 79 mm
Centerhøjttaler vægt:	4300 g
Subwoofer dimensioner (BxDxH):	435 x 137 x 350 mm
Subwoofer vægt:	6000 g