ZyXEL SFP10G-LR Manual

ZyXEL Skifte SFP10G-LR

Læs gratis den danske manual til ZyXEL SFP10G-LR (1 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om ZyXEL SFP10G-LR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

SFP and SFP+ Transceivers

User’s Guide

Removing Fiber-optic Cable

Attach an ESD preventive wrist strap to your

wrist and to a bare metal surface on the chassis.

Disconnect all ﬁber-optic cables from the

SFP/SFP+ module.

Installing a Module 1

Attach an ESD preventive wrist strap to your

wrist and to a bare metal surface.

Remove the a module from its protective

packaging.

Locate the transmit (Tx) and the receive (Rx)

markings on the module.

Align the module in front of the slot opening on a

device.

Insert the module into the slot until the module

snaps into place

Note : Module installation orientation varies

depending on your device. Your module comes

with a mechanism that prevents incorrect

insertion. Do NOT force or twist the module into a

slot. Do NOT insert an SFP+ module into a

1-Gigabit SFP slot.

Connecting a Fiber-optic Cable 2

Remove the dust plugs from a module and the

cables.

Identify the signal transmission direction of the

ﬁber-optic cable and the module. Insert one end

of the ﬁber-optic cable into the module.

Insert the other end of the ﬁber-optic cable into a

remote device.

Note : Refer to the user’s guide that comes with

your device for module slot status.

Introduction

EU Importer

Zyxel Communications A/S

Gladsaxevej 378, 2. th. 2860 Søborg, Denmark

http://www.zyxel.dk

US Importer

Zyxel Communications, Inc

1130 North Miller Street Anaheim, CA 92806-2001

http://www.us.zyxel.com

Removing a Module

Unlocking a Module

Insert the dust plug into the ports on a module.

Pull out the latch and down to unlock a module.

Using your thumb and index ﬁnger, grasp the

tabs on both sides of the module and carefully

slide it out of the slot.

Note : Do NOT force or twist the module out of a

slot.

Use a transceiver module for connection to a remote device. SFP

and SFP+ transceiver modules are hot swappable. You can install

and remove a module while your device is operating.

SFP/SFP+ modules both use 3.3V power input and LC-type

connectors.

SFP/SFP+ modules support data rate of 100M/1G/10G bps and

single-mode/multi-mode connection based on its speciﬁcation.

Handling Warning

All modules are static sensitive. To prevent damage from

electrostatic discharge (ESD), it is recommended you attach an ESD

preventive wrist strap to your wrist and to a bare metal surface

when you install or remove a module.

All modules are dust sensitive. When not in use, always keep the

dust plug on. Avoid getting dust and other contaminant into the

optical bores, as the optics do not work correctly when obstructed

with dust.

Safety Warning

All modules are equipped with a Class 1 laser, which emits invisible

radiation. Read the following safety warnings carefully.

•To avoid possible eye injury, do not look into an operating

ﬁber-optic module’s connectors.

•Laser radiation is present when the device or system is powered

up.

•Only trained and qualiﬁed personnel should be allowed to install or

replace these modules.

Environmental Warnings

•Dispose of your ﬁber-optic module according to all national laws

and regulations.

...warranty must be validated with the seller's ....

See the Zyxel website for a list of supported transceivers.

Produkt Specifikationer

Mærke:	ZyXEL
Kategori:	Skifte
Model:	SFP10G-LR
Bredde:	14.8 mm
Dybde:	56.5 mm
Højde:	11.85 mm
Vægt:	20 g
Harmoniseret systemkode (HS):	85369010
Maksimal dataoverførselshastighed:	10000 Mbit/s
SFP modtagertype:	Fiberoptisk
Grænsefladetype:	SFP+
Fiber optisk strømstik:	SFP+
Enkelttilstand fiber (SMF) understøttet:	Ja
Maksimal overførselsafstand:	10000 m
Bølgelængde:	1310 nm
Antal produkter inkluderet:	1 stk
Understøtter hot-plug:	Ja
Fiberkanal porte:	2