Adder Link AV102T Manual

Adder AV forlænger Link AV102T

Læs gratis den danske manual til Adder Link AV102T (4 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Adder Link AV102T, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
The AdderLink AV 2-Port Computer Access Module is a highly compact device that allows you to share a
single computer between two sets of peripheral devices.
The AdderLink AV 2-Port Computer Access Module connects to various ports on your computer. You then
connect it via CAT 5, 5e or 6 cabling to two AdderLink AV receiver units (either AdderLink AV100R or
AV101R), each of which can be located up to 300 metres from the module. Your video displays and speakers
are linked to the remote AdderLink AV100 or AV101 receiver units. See important note below.
The AdderLink AV 2-Port Computer Access Module uses a USB port to derive its power from the host
computer, dispensing with the need for a separate power supply and thus simplifying installation.
2-Port Computer Access Module
Quick Start (ALAV102T-USB)
Adder Technology Limited,
Technology House,
Trafalgar Way, Bar Hill,
Cambridge, CB23 8SQ,
United Kingdom
Tel: +44 (0)1954 780044
Fax: +44 (0)1954 780081
© 2011 Adder Technology Ltd • Release 1.0e • June 2011 • Part No. MAN-ALAV102T-USB-QS-ADDER
All trademarks are acknowledged. Documentation by Corporate Text & Design (www.ctxd.com)
Adder Corporation,
350R Merrimac Street,
Newburyport,
MA 01950,
United States of America
Tel: +1-888-932-3337
Fax: +1-888-275-1117
support@adder.com
www.adder.com
Safety information
• For use in dry, oil free indoor environments only.
• Do not use to link between buildings.
• Not suitable for use in hazardous or explosive
environments or next to highly flammable
materials.
• Ensure that all twisted pair interconnect cables
are installed in compliance with all applicable
wiring regulations.
• Do not connect the CATx link interface (RJ45
style connector) to any other equipment,
particularly network or telecommunications
equipment.
• Where possible, avoid laying the twisted pair
link cable(s) alongside power cables.
• Do not attempt to service the module yourself.
• The modules do not provide ground isolation
and should not be used for any applications
that require ground isolation or galvanic
isolation.
• For correct operation, the transmitter
and receiver modules must have ground
connections. At the computer end, this is
achieved by ensuring that the computer that
the module is connected to has a ground
connection. At the audio/visual device end, this
can be achieved by ensuring that the power
supply is connected to a grounded power
outlet. Alternatively, a ground connection will
be made via the monitor, if the monitor is itself
grounded.
Warranty
Adder Technology Ltd warrants that this product
shall be free from defects in workmanship and
materials for a period of two years from the date
of original purchase. If the product should fail to
operate correctly in normal use during the warranty
period, Adder will replace or repair it free of charge.
No liability can be accepted for damage due to
misuse or circumstances outside Adder’s control.
Also Adder will not be responsible for any loss,
damage or injury arising directly or indirectly from
the use of this product. Adder’s total liability under
the terms of this warranty shall in all circumstances
be limited to the replacement value of this product.
If any difficulty is experienced in the installation or
use of this product that you are unable to resolve,
please contact your supplier.
AdderLink AV
2-port Computer
Access Module
What you may additionally need
What’s in the box
Adder Asia Pacific
6 New Industrial Road,
Hoe Huat Industrial Building
#07-01,
Singapore 536199
Tel: +65 6288 5767
Fax: +65 6284 1150
RECEIVER
SKEW
GB
SKEW
RG
BRIGHT SHARP
LINK OUT
101
ADDERLINK
OUT
OUT
AdderLink AV
100R or 101R
receiver units
IMPORTANT
Earlier versions of AdderLink
AV100R and AV101R receivers are
not compatible with the AdderLink
AV102T transmitter. Use only serial
numbers as follows:
• AdderLink AV 100R - s/n 6000
or greater.
• AdderLink AV 101R - s/n 2000
or greater.
Audio
USB
Video
Serial port
Output to
video display
and speakers
Output to
video display
and speakers
RECEIVER
ADDERLINK
OUT
OUT
RECEIVER
ADDERLINK
OUT
OUT
Resolutions and cable lengths
The maximum resolutions achievable are:
1600 x 1200 x 60Hz at 200m and 1280 x
1024 x 60Hz at 300m.
Do not exceed 300m cable lengths in any
installation.
Host computer connections
The module does not require a power adapter
because it derives all of its power from the host
computer. Therefore the USB cable must always
be connected to a USB port on the computer that
is capable of providing up to 500mA.
Receiver unit connections
For details about connections at the receiver
units, please refer to the guides for those devices.
1 Disconnect the CATx link
cables from the module. This
procedure will not work if the
CATx links are present.
2 Attach the module’s Video
connector to the monitor
whose EDID is required (or
an Adder DDC Ghost unit
containing the required EDID).
3 Attach the USB and serial port
connectors to a computer. See
‘Serial port configuration’.
4 On the computer, open a
terminal program and send
the character (0x65) to e
the Com port to which the
module’s serial connector is
attached.
If the EDID harvest is
successful, the module
will send to confirm. If OK
unsuccessful, it will send FAIL
- check the connections and
try again.
5 Reconnect the module in
the usual manner for normal
operation.
EDID display information
The module contains a default set of EDID information that supports
display resolutions up to 1600 x 1200 @ 60Hz. If required, you can
harvest and store new EDID information from your display or an Adder
DDC Ghost device.
Serial port configuration
The module can automatically alter its baud rate
to match that of the host computer’s serial port.
To do this the other serial parameters must first
be correct: 8 data bits, no parity, 1 stop bit and
no hardware handshaking. These are usually the
default settings, however, if you do need to alter
them, open the Windows Device Manager, locate
the entry for the COM port to which the module
is connected and view the Properties > Port
Settings tab. Once set, open a terminal program
and send a Return (carriage return) to the Com
port to which the module is attached until
the message USB Dual Access CAM version
1.00 is returned. The module can now accept
commands.
IMPORTANT
Earlier versions of AdderLink
AV100R and AV101R receivers are
not compatible with the AdderLink
AV102T transmitter. Use only serial
numbers as follows:
• AdderLink AV 100R - s/n 6000
or greater.
• AdderLink AV 101R - s/n 2000
or greater.

Produkt Specifikationer

Mærke: Adder
Kategori: AV forlænger
Model: Link AV102T

Har du brug for hjælp?

Hvis du har brug for hjælp til Adder Link AV102T stil et spørgsmål nedenfor, og andre brugere vil svare dig


AV forlænger Adder Manualer

Adder

Adder Link XD641 R Manual

13 August 2025
Adder

Adder Link XD642 T Manual

13 August 2025
Adder

Adder Link XD612 R Manual

12 August 2025
Adder

Adder Link XD614 T Manual

12 August 2025
Adder

Adder Link XD642 R Manual

12 August 2025
Adder

Adder Link XD614 R Manual

12 August 2025
Adder

Adder Link XD641 T Manual

12 August 2025
Adder

Adder Link X2-Silver DA Manual

17 Juli 2025
Adder

Adder Link XD642 Manual

17 Juli 2025
Adder

Adder Link X50-MS Manual

17 Juli 2025

AV forlænger Manualer

Nyeste AV forlænger Manualer

Opticis

Opticis SDISE-100-TR Manual

1 Oktober 2025
Opticis

Opticis DPFX-300-TR Manual

1 Oktober 2025
Opticis

Opticis HDFX-500-TR Manual

30 September 2025
Opticis

Opticis SDIX-100-TR Manual

30 September 2025
Vivolink

Vivolink VLHDMIEXTHDB2.0 Manual

23 September 2025
Crestron

Crestron HD-EXT4-C-B Manual

23 September 2025
IMG Stageline

IMG Stageline FLY-16SET Manual

20 September 2025
Vivolink

Vivolink VLHDMIEXT60 Manual

16 September 2025
MuxLab

MuxLab 500451 Manual

16 September 2025
MuxLab

MuxLab AV/IR Pass-Thru Balun Manual

16 September 2025