Adesso NuScan 2800U Manual
Adesso
Stregkodelæser
NuScan 2800U
Læs gratis den danske manual til Adesso NuScan 2800U (94 sider) i kategorien Stregkodelæser. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Adesso NuScan 2800U, eller vil du spørge andre brugere om produktet?
Side 1/94

- 1 -
USER GUIDE

- 2 -
About This User Guide
Pls read all the content of the user guide carefully to use the products safely and effectively. You
are advised of keeping it properly for your using reference.
Disclaimer
Please do not dismantle the product or tear up the seal on it, otherwise we won’t provide
warranty or replacement service.
The pictures in this user guide are for reference only. If there are any pictures which not match
the actual product, please take actual products as the standard. Updated information is subject to
change without notice.
All information contained in this guide are protected by copyright, and our company reserves all
rights. All or part of this guide is prohibited to excerpt, copy, bundle other products, or sell without
the written permission from us.
Service Information
For technical assistant or product service and repair, please contact us.

- 3 -
Version Record
Version number
Version description
Version date
SV1.1_HV1.2_190330_201903
30d024-190330
Initial version
2019-4-15
SV1.1_HV1.2_190330_d025
The gs128 menu has been modified. It is invalid by
default
2019-4-16
SV1.1_HV1.2_190330_d027
1. Modified the C error of 39full conversion tail;
2. The 39full conversion is not correct;
3. Change the setting of switching to USB keyboard
mode, save the parameters before setting;
4. Modify the sound prompt error of USB serial port
setting success;
5. Modified compatible XP system;
6. Modify the problem that the key is pressed until
the decoding is successful or the key is released to
turn off the light;
7. Add USB network mode, communicate with upper
computer through USB network mode;
2019-4-17
SV1.3_HV1.2_190330_d027
1. The lighting effect is modified to improve the
decoding effect;
2. The communication between USB network and
host computer is modified except win10 system;
2019-4-19
SV1.4_HV1.2_190330_d027
1. Add the function of modifying IP address, which
can be set by upper computer or scanning mode
2. When set to USB network mode, the default IP
2019-4-30

- 4 -
address is 32.45.78.1
SV1.5_HV1.2_190330_d027
1. The default frequency of sound is changed to 2.7K
2. The shipping version of hs-26
2019-5-6
SV1.6_ZS_HV1.2_2K7_190330
_d031
1. Greatly improve decoding performance
2. Early exit decoding function is set
3. Modified the problem of missing callback function
4. Code128 can solve hidden character, which is
related to menu;
2019-5-23
SV1.7_ZS_HV1.2_2K7_190330
_d031
1. The default value of output code length is changed
to 4-50
2. Change the maximum sound to 2.7K
2019-5-23
SV1.7_ZS_HV1.2_2.048K_190
330_d031
Change the maximum sound to 2.048k
2019-5-23
SV1.8_ZS_HV1.2_2.048K_QZ
_190330_d033
1. Add hardware watchdog
2. Change the maximum sound to 2.048k
3. Solve the problem of noise during startup
4. Because of RTC failure, the callback function
adopts counting method
5. Speed up anti white code
6. Modify hid sending speed
2019-5-30
SV1.8_ZS_HV1.2_2.048K_MZ
_190330_d033
1. Add hardware watchdog
2. Change the maximum sound to 2.048k
3. Solve the problem of noise during startup
2019-5-31

- 5 -
4. Because of RTC failure, the callback function
adopts counting method
5. Speed up anti white code
6. Modify hid sending speed
7. Serial output, no terminator, initialized to self
sensing mode
SV1.9_ZS_HV1.2_2K7_QZ_19
0330_d033
1. Initialize turn on anti white code
2. Can switch to self sensing mode
2019-6-1
SV1.9_ZS_HV1.2_2.048K_QZ
_190330_d033
1. Initialize turn on anti white code
2. Can switch to self sensing mode
2019-6-1
SV2.0_ZS_HV1.2_2.048K_MZ
_190330_d033
Add aging test mode
2019-6-5
SV2.0_ZS_HV1.2_2K048_QZ_
190605_d037
1. Pdf optimization
2, DM optimization
3. QR high density optimization
4. QR code crash
5. The problem of PDF missing angle decoding
2019-6-10
SV3.4_ZS_HV1.0_PTY_P9_H
T_OLD_20200317.250718
1.UPC-A to EAN-13.
2.EAN-13 to ISSN
3.UPC-A/EAN/JAN extra-code
2020-3-24
SV3.5_ZS_HV1.0_PTY_P14_H
T_OLD_20200422_4.7.200416.
250718
2020-4-23

- 6 -
SV3.7_ZS_HV1.0_PTY_P16_H
T_OLD_20200511_4.7.200416.
250718
1. Solve suffix cannot be added
2. Solve the problem that data lost when UPC-
A to EAN-13
3. Solve the problem that EAN13 to ISSN doesn't w
ork
4. Add getting CPUID barcode function (for interna
l use only)
5. Before MP6300Y (2.7khz buzzer) 2019.11.11 ver
sion are all old camera
2020-5-13

- 7 -
Catalogue
1.Product Introduction
................................................................................................................ - 14 -
1.1 Main feature
................................................................................................................... - 14 -
1.2 Open package
................................................................................................................. - 15 -
1.3 Communication port
....................................................................................................... - 15 -
1.4 Start-up, shutdown, standby and restart
.......................................................................... - 15 -
1.5 Maintenance
................................................................................................................... - 15 -
1.6 Reading skills
................................................................................................................. - 16 -
2.Barcode Menu
.......................................................................................................................... - 17 -
2.1 Mark Setting
................................................................................................................... - 17 -
2.2 Setting barcodes
............................................................................................................. - 17 -
2.2.1 Turn on/Turn off configuration code
..................................................................... - 17 -
2.2.2 Restore Factory Defaults
....................................................................................... - 17 -
2.2.3 Read product batch version
................................................................................... - 18 -
2.2.4 Time-out setting
.................................................................................................... - 18 -
2.2.5 Read user defaults
................................................................................................. - 19 -
2.2.6 Interface Setting
.................................................................................................... - 19 -
2.2.7 Serial port setting
.................................................................................................. - 20 -

- 8 -
2.2.8 LED control
.......................................................................................................... - 23 -
2.2.9 Character escape
................................................................................................... - 23 -
2.2.10 GS Control Character escape(Control Character Escape Function need to be enable)
(Not enable)
............................................................................................................. - 24 -
2.2.11 Prefix setting
....................................................................................................... - 25 -
2.2.12 Suffix setting
...................................................................................................... - 25 -
2.2.13 Unicode Output Mode
......................................................................................... - 26 -
2.2.14 Inverse code option
............................................................................................. - 26 -
2.2.17 Virtual keyboard
................................................................................................. - 27 -
2.3 Beeper and LED notifications
......................................................................................... - 28 -
2.3.1 Beeper Volume setting
.......................................................................................... - 28 -
2.3.2 Startup beep
.......................................................................................................... - 28 -
2.3.3 Good read beep
..................................................................................................... - 28 -
2.3.4 Beep pitch-good read
............................................................................................ - 29 -
2.3.5 Beep duration-good read
....................................................................................... - 29 -
2.3.6 Error sound
........................................................................................................... - 30 -
2.3.7 Good-read LED
.................................................................................................... - 31 -
2.4 Timeout between decodes (Same barcodes)(works in Auto scan mode)
.......................... - 31 -

- 9 -
2.5 USB keyboard setting
..................................................................................................... - 32 -
2.6 Line feed setting(USB keyboard)
.............................................................................. - 33 -
2.7 USB keyboard text-transform
......................................................................................... - 33 -
2.8 Keyboard layout setting
.................................................................................................. - 34 -
2.9 Barcode data hiding settings ........................................................................................... - 37 -
2.10 Symbologies
................................................................................................................. - 38 -
2.10.1 Enable/disable all Symbologies
........................................................................... - 38 -
2.10.2 Enable/disable all 1D Symbologies
..................................................................... - 39 -
2.10.3 Enable/disable all 2D Symbologies
..................................................................... - 39 -
2.10.4 Codabar
.............................................................................................................. - 40 -
2.10.5 Codabar start/ending character setting
................................................................. - 40 -
2.10.6 Codabar limitation of length
................................................................................ - 40 -
2.10.7 Code 39
.............................................................................................................. - 40 -
2.10.8 Code 39 check bit
............................................................................................... - 41 -
2.10.9 Code 39 Full ASCII
............................................................................................ - 41 -
2.10.10 Code 39 limitation of length
.............................................................................. - 42 -
2.10.11 Code 32 (Code 39 needs to be enabled)(Not Enabled)
............................... - 42 -
2.10.12 Interleaved 2 of 5 (ITF5)
............................................................................. - 42 -

- 10 -
2.10.13 Interleaved 2 of 5 (ITF5)check bit
............................................................... - 43 -
2.10.14 Interleaved 2 of 5 (ITF5)length setting
........................................................ - 43 -
2.10.15 Interleaved 2 of 5 Limitation of length
.............................................................. - 45 -
2.10.16 Industrial 2 of 5 (Industrial 25code)(4-24bit)
............................................... - 45 -
2.10.17 Industrial 2 of 5 Limitation of length
................................................................. - 45 -
2.10.18 Matrix 2 of 5 (matrix 25 code)(4-24 bit)
....................................................... - 46 -
2.10.19 Matrix 2 of 5 Limitation of length
..................................................................... - 46 -
2.10.20 Standard 25 ....................................................................................................... - 46 -
2.10.21 Standard 25Limitation of length ........................................................................ - 46 -
2.10.22 Standard 25 check bit setting
............................................................................. - 47 -
2.10.23 Code 93
............................................................................................................ - 47 -
2.10.24 Code 93 Limitation of length
............................................................................ - 48 -
2.10.25 Code 11(
Not Enabled
)
................................................................................. - 48 -
2.10.26 Code 11 check bit output(
Not Enabled
)
........................................................ - 48 -
2.10.27 Code 11 check bit option(
Not Enabled
)
........................................................ - 48 -
2.10.28 Code 11 Limitation of length(
Not Enabled
)
.................................................. - 49 -
2.10.29 Code 128
.......................................................................................................... - 49 -
2.10.30 Code 128 Limitation of length
.......................................................................... - 50 -

- 11 -
2.10.31 GS1-128(requires CODE 128 to be enable)
.................................................... - 50 -
2.10.32 ISBT-128(Not enable)
.................................................................................. - 50 -
2.10.33 Plessey(Not enable)
..................................................................................... - 51 -
2.10.34 Plessey Limitation of length(Not enable)
..................................................... - 51 -
2.10.35 Plessey check bit optional(Not enable)
......................................................... - 51 -
2.10.36 MSI plessey(Not enable)
.............................................................................. - 52 -
2.10.37 MSI plessey Limitation of length(Not enable)
.............................................. - 52 -
2.10.38 MSI plessey check bit output (Not enable)
.................................................. - 53 -
2.10.39 MSI plessey Check mode selection setting
........................................................ - 53 -
2.10.40 UPC-A
.............................................................................................................. - 54 -
2.10.41 UPC-A check bit
............................................................................................... - 54 -
2.10.42UPC-A to EAN-13(Not enable)
..................................................................... - 54 -
2.10.43 UPC-E
.............................................................................................................. - 55 -
2.10.44 UPC-E check bit
............................................................................................... - 55 -
2.10.45 UPC-E expand UPC-A
...................................................................................... - 55 -
2.10.46 EAN/JAN-8
...................................................................................................... - 56 -
2.10.47 EAN/JAN-13
.................................................................................................... - 56 -
2.10.48 UPC/EAN/JAN extra-code(Not enable)
....................................................... - 56 -

- 12 -
2.10.49 EAN13 to ISBN
................................................................................................ - 57 -
2.10.50 EAN13 to ISSN(Not enable)
........................................................................ - 57 -
2.10.51 GS1 DataBar(RSS14)(Stacked)
.................................................................... - 57 -
2.10.52 GS1 DataBar(RSS14)(Stacked) AI(01)character send(Not enable)
..... - 58 -
2.10.53 GS1 DataBar Limited
........................................................................................ - 58 -
2.10.54 GS1 DataBar Limited AI(01)character send(Not enable)
......................... - 58 -
2.10.55 GS1 DataBar Expanded
.................................................................................... - 59 -
2.10.56 PDF417
............................................................................................................ - 59 -
2.10.57 Micro PDF417
.................................................................................................. - 59 -
2.10.58 QR Code
........................................................................................................... - 60 -
2.10.59 Micro QR
.......................................................................................................... - 60 -
2.10.60 Data Matrix
....................................................................................................... - 60 -
2.11 User-defined prefix setting(Not enable)
................................................................... - 61 -
2.12 User-defined suffix setting(Not enable)
................................................................... - 62 -
2.13 Barcode prefix&suffix order selection(Not enable)
.................................................. - 62 -
2.14 Code ID setting(Not enable)
.................................................................................... - 63 -
2.15 AIM ID setting(Not enable)
..................................................................................... - 64 -
Appendix
.................................................................................................................................... - 65 -

- 13 -
Appendix 1 Data and edit barcode
........................................................................................ - 65 -
Appendix 2 Barcode type ID table
........................................................................................ - 68 -
Appendix 3 Invisible character ASCII table
.......................................................................... - 73 -
Appendix 4 Visible character ASCII table
............................................................................ - 75 -
Appendix 5 Default setting table
.......................................................................................... - 78 -
Appendix 6 operational character (USB keyboard)
............................................................... - 87 -
Appendix 7 operational character (serial port and USB-VCOM)
.......................................... - 89 -
Some feature configuration instructions and examples ................................................................ - 91 -
Barcode length limit configuration example .................................................................. - 93 -
Example for USB keyboard send speed configuration . ............................................... - 94 -

- 14 -
1.Product Introduction
This user guide applies to MP6300Y, which identify 1D&2D barcodes by 2D image
scanning pattern. The scanners above are of strong identification capability, and support automatic
continuous scanning mode with fast and flexible scanning speed.
In this chapter, we will introduce the instruction of scanner with pictures, please compare to the
scanner you bought when reading this user guide, which is good for your understanding. This chapter
applies to regular users, maintenance personnel, and software developers.
1.1 Main feature
* Complete independent research and development, possessing the complete set of patent, plug
and play without the need to install driver.
* Wide voltage design to avoid the data can’t be transmitted due to voltage fluctuation.
* 32-bit master chip equipped with patented software, the scanner can smoothly decode reflective,

- 15 -
wrinkled, blurred, and colorful barcode, and can also normally scan in light and dark environment.
* Adopt all tantalum capacitors and anti-oxidation optical technology, avoiding the problem of
performance declining after long-term using.
1.2 Open package
Open the package and take out the products and accessories. Check whether all items are complete
and whether there are damaged parts according to the packing list. If there are any damaged or missing
parts, please keep the original packaging and contact your supplier for after-sales service.
1.3 Communication port
The scanner must be connected to a host to operate. Host can be a PC, POS machine, intelligent
terminal with USB or RS-232 interface.
USB
USB interface on host
RS-232
RS-232 interface on host
1.4 Start-up, shutdown, standby and restart
Start-up:Connect host computer with scanner, which will automatically start-up and in working
state.
Shutdown:Remove the data cable which is connected with scanner; remove the USB which is
connected with host computer; remove the power adapter which is inserted into RS-232 serial port.
Standby:Scanner with automatic sleep standby function, if 30 minutes without work it will be in
standby mode, but it will automatically start-up when barcode approach.
Restart:If the scanner crashes or doesn't respond, please switch it off and restart.
1.5 Maintenance
*
The window must be kept clean, the supplier do not bear the guarantee responsibility due to the

- 16 -
improper maintenance.
*
Avoid the window being wear and tear or scratched by hard object
*
Use the hairbrush to remove the stain on the window
*
Clean the window with a soft cloth, such as lens cleaning cloth
*
Spraying liquid onto the window is prohibited.
*
Prohibit any cleaning solvents, except for the cleaning water.
1.6 Reading skills
If the barcode is small, it should be closer to the scanning window; if the barcode is large, it
should be far away from the scanning window a little more, thus easier to be read correctly.
If the barcode is highly reflective (for example, the coated surface), you may need to tilt the
barcode at an angle to successfully scan it.
Barcode scanning example:

- 17 -
2.Barcode Menu
This model of laser desktop barcode scanner is designed to change settings by reading some
special barcode, which we will give you a detailed introduction and show you all the barcodes for the
corresponding setting in this section.
The greatest advantage of this setting method is direct, intelligible and user friendly.
2.1 Mark Setting
2.2 Setting barcodes
2.2.1 Turn on/Turn off configuration code
When the configuration code is turn on, All configuration codes available;
When the configuration code is turn off, you need setting it.
Configuration Code Turn Off
2.2.2 Restore Factory Defaults
1
2
Configuration Code Turn on
(Default)
Configuration Code Turn On(Default)

- 18 -
Restore Factory Default s
2.2.3 Read product batch version
2.2.4 Time-out setting
Select time-out interval
No Time-Out(Default)
3s
5s
Product Batch Version

- 19 -
10s
2.2.5 Read user defaults
Save the current m enu settings as u ser -def ined menu settings.
Save User Defaults
You can restore the menu setti ngs for the user-defin ed menu settings.
Restore User Defaults
2.2.6 Interface Setting
This desktop scanner support USBKB 、 USB to serial port、 serial port
interface.
You can set USB PC KB、 USB MAC KB interface by scan ning below barcode.
USB KB(Default)

- 20 -
USB MAC KB( Not en able)
You can set serial port interface by scanning below barcode.
Serial port
You can set USB to serial port interface by scanning belo w barcode. (Need
drive, please cont act the sales)
USB to Serial Port( Not enable)
USB Upgrade
2.2.7 Serial port setting
2.2.7.1 Baud rate setting
Host mode (command decoding +
physical serial port)

- 21 -
2.2.7.2 Serial port data bits, stop bits, check bit setting
Baud rate 48 00
Baud rate 115200
7 data bits,1 stop bit,no check bit
7 data bits,1 stop bit,even-
parity check
Baud rate 96 00( Default)
Baud rate 38400
Baud rate 19200
Baud rate 57600

- 22 -
7 data bits,1 stop bit,odd-
parity check
7 data bits,2 stop bits,no
check bit
7 data bits,2 stop bit,even-
parity check
7 data bits,2 stop bits,
odd-parity check
8 data bits,1 stop bit,no
check bit
8 data bits,1 stop bit,even-
parity check
8 data bits,1 stop bit,odd-
parity check
8 data bits,2 stop bits,no
check bit

- 23 -
2.2.8 LED control
Normal Mode(Default)
Always Off
Always On
2.2.9 Character escape
Enable character escape
8 data bits,2 stop bit,
even-parity check
8 data bits,2 stop bits,odd-parity check

- 24 -
Disable Character Escape(Default)
2.2.10 GS Control Character escape(Control Character Escape Function need to be enable)(Not
enable)
No ReplacemEnt (Not Enable)
Note: Output character“Ç”,must scan "Enable virtual keyboard "
Open (Mode 1)"or (Mode 2) or (Mode 3) first
Replace With Ç(Not enable)
Replace with | (Not enable)
Replace with ^] (Not enable)
Replace with ](Not enable)

- 25 -
Replace with <GS>(Not enable)
2.2.11 Prefix setting
No prefix(Default)
<STX><data>
2.2.12 Suffix setting
No Suffix
<Data><CR>
<Data><LF>

- 26 -
<Data><CR><LF>(Default)
<Data><TAB>
<Data>< ETX>
2.2.13 Unicode Output Mode
Latin-1(Default)
GBK( lNotepad/excel)
UNICODE( Word)
2.2.14 Inverse code option
(Only 1D/Data Matrix/Aztec)
Only Decode Normal Code(Default)

- 27 -
Only Decode Inverse Code(Not Enable)
Decode Both Normal Code And Inverse Code
2.2.17 Virtual keyboard
Mode 1: The characters between 0x20 and 0xFF are output in the virtual keyboard mode that is not
supported by the current keyboard layout. The characters between 0x00 and 0x1F are defined
according to the control characters.
Mode 2: All characters between 0x20 and 0xFF are output under the virtual keyboard mode, and
characters between 0x00 and 0x1F are defined according to the control characters.
Mode 3: The characters used between 0x00 and 0xFF are output under the virtual keyboard mode.
Disable Virtual K eybo ard( Default)
Enable Virtual Keyboard (Mode 1)
标准模式
上下镜像模式 2

- 28 -
Enable Virtual Keyboard (Mode 2)
Enable Virtual Keyboard (Mode 3)
2.3 Beeper and LED notifications
2.3.1 Beeper Volume setting
Volume Low
Volume High( Default)
2.3.2 Startup beep
Shut Down Startup Beep
Open Startup Beep
( Default)
2.3.3 Good read beep

- 29 -
Good Read Beep On
Good Read Beep Off( Defaul
t)
2.3.4 Beep pitch-good read
Low Pitch( Default)
Middle Pitch
High Pitch
2.3.5 Beep duration-good read

- 30 -
Tone Long( Defaul
t)
Tone Pip
2.3.6 Error sound
You will hear 4 continue alarm sounds wh en data uplo ad failure, one single
alarm soun d means scan indistinguishableness barcode.
Error Sound Low Pitch( Default)
Error Sound Middle Pitch
Error Sound High Pitch

- 31 -
2.3.7 Good-read LED
Good-Read LED Off
Good-Read LED On( Default)
2.4 Timeout between decodes (Same barcodes)(works in Auto scan mode)
2.4.1 Timeout between decodes (Same barcodes)
To avoid being repeatedly with a barcode, you can set the scan interval.
200ms
500ms(Default)
750ms
1s

- 32 -
2.4.2 Reading time
Single Reading Time
In the inductive reading mode, this parameter refers to the maximum time that the reading
engine is allowed to continuously collect and recognize before reading is successful. After the
successful reading or the timeout of a single reading, the reading engine will enter the interval of not
collecting and reading. The setting range of single code reading time is 0.1-25 seconds, and the step
length is 0.1 seconds. Indicates that the reading time is infinite. The default duration is 3.0 seconds.
2.5 USB keyboard setting
There barcode is used to set the update speed when scanner is in USB keyboard pattern. If the
performance of your PC is lower, we suggest you choose slow update speed to make sure the scanner
update the right data.
Slow Update Speed
Middle Update Speed
Fast Update Speed(Default)

- 33 -
User-Defined Update Speed( 2ms~50ms)
2.6 Line feed setting(USB keyboard)
Only 0A(Line Feed)Works
Only 0D(Carriage Return)Works
(Default)
Both 0A(LR) And 0D(CR) Works
2.7 USB keyboard text-transform
Normal Output(Default)
Case Reversal
All Caps

- 34 -
Lower Case
2.8 Keyboard layout setting
E n gl i sh ( U n i t e d S t a t e s )
French (France)
Italian (Italy)
Italian 142 (Italy)(Not enable)
German (Germany)

- 35 -
Spanish (Spain)
Spanish (Latin America)(Not enable)
Finnish(Not enable)
Japanese(Not enable)
Russian (MS)(Not enable)
Russian (typewriter)(Not enable)
Arabic (101)(Not enable)

- 36 -
Irish(Not enable)
Polish (214)(Not enable)
Polish (Programmers)(Not enable)
Dutch (Netherlands)(Not enable)
Czech (QWERTZ)(Not enable)
Portuguese (Portugal)
Portuguese (Brazil)

- 37 -
Swedish (Sweden)(Not enable)
Turkish Q
Turkish F(Not enable)
Greek (MS)(Not enable)
French (Belgium)
English (UK) (Not enable)
2.9 Barcode data hiding settings

- 38 -
Original Barcode Data
Transfer Start Field Only
Transfer Only Intermediate Fields
Transfer Only End Fields
Start And End Fields Only
Set Start Field Length
Set End Field Length
2.10 Symbologies
2.10.1 Enable/disable all Symbologies
Enable all barco de might slow down scan ner decod e speed. We suggest
enable th e barcode you need based on your scene. Enable all barcode is
default

- 39 -
Enable All Symbologies( Default)
Disable All Symbologies
2.10.2 Enable/disable all 1D Symbologies
2.10.3 Enable/disable all 2D Symbologies
Enable All 1D Symbologies
Disab le All 1D Symbol ogies
Enable All 2D Symbologies
Disab le all 2D Symbologies

- 40 -
2.10.4 Codabar
Enable Codabar
Disable Codabar
2.10.5 Codabar start/ending character setting
Don’t Send Codabar Start/ending Character (Default)
Send Codabar Start/Ending Character
2.10.6 Codabar limitation of length
Codabar Min Length(1~127bit)
Codabar Max Length(1~127bit)
2.10.7 Code 39

- 41 -
Enable Code 39
Disable Code 39
2.10.8 Code 39 check bit
Disable Code 39 Check Bit (Default)
Enable Code 39 Check Don’t Send Check Bit
Enable Code 39 Check Send Check Bit
2.10.9 Code 39 Full ASCII
Enable Full ASCII

- 42 -
Disable Full ASCII (Default)
2.10.10 Code 39 limitation of length
Code 39 Max Length (1~127bit)
Code 39 Min Length (1~127bit)
2.10.11 Code 32 (Code 39 needs to be enabled)(Not Enabled)
Enable Code 32
Disable Code 32
2.10.12 Interleaved 2 of 5 (ITF5)
Enable ITF25

- 43 -
Disable ITF25
2.10.13 Interleaved 2 of 5 (ITF5)check bit
Disable ITF25 Check (Default)
Enable ITF25 Check Don’t Send Check Bit
Enable ITF25 Check Send Check Bit
2.10.14 Interleaved 2 of 5 (ITF5)length setting
ITF25 No Fixed Length (4-128bit)(Default)
ITF25 6 Bit Length

- 44 -
ITF25 8 Bit Length
ITF25 10 Bit Length
ITF25 12 Bit Length
ITF25 14 Bit Length
ITF25 16 bit Length
ITF25 18 bit Length
ITF25 20 bit Length
ITF25 22 bit Length

- 45 -
ITF25 24 bit length
2.10.15 Interleaved 2 of 5 Limitation of length
Interleaved 2 of 5 min limitation length (4~128 bit)
Interleaved 2 of 5 max limitation length (4~128bit)
2.10.16 Industrial 2 of 5 (Industrial 25code)(4-24bit)
Enable Industrial 2 of 5
Disable Industrial 2 of 5
2.10.17 Industrial 2 of 5 Limitation of length
Industrial 2 of 5 min length (4~128bit)
Industrial 2 of 5 max length (4~128bit)

- 46 -
2.10.18 Matrix 2 of 5 (matrix 25 code)(4-24 bit)
Enable Matrix 2 of 5
Disable Matrix 2 of 5
2.10.19 Matrix 2 of 5 Limitation of length
Matrix 2 of 5 min length (4~128 bit)
Matrix 2 of 5max length (4~128bit)
2.10.20 Standard 25(Not enable)
Enable Standard 25 (default)
Disable Standard 25
2.10.21 Standard 25Limitation of length

- 47 -
Standard 25 min length(4~128 bit)
Standard 25max length
(4~128 bit)
2.10.22 Standard 25 check bit setting
Standard 25 don’t check (Default)
Standard 25 Check, Not Output
Standard 25 Check And Output
2.10.23 Code 93
Enable Code 93
Disable Code 93

- 48 -
2.10.24 Code 93 Limitation of length
Code 93 min length(1~127 bit)
Code 93 max length(1~127 bit)
2.10.25 Code 11(Not Enabled)
Enable Code 11
Disable Code 11 (Default)
2.10.26 Code 11 check bit output(Not Enabled)
Enable Code 11Check Bit Output
Disable Code 11check Bit Output
2.10.27 Code 11 check bit option(Not Enabled)

- 49 -
Disable Code 11 Check Bit (Default)
Code 11 One Check Bit
Code 11 Two Check Bit
2.10.28 Code 11 Limitation of length(
Not Enabled
)
Code 11 min length(1~127 bit)
Code 11 max length(1~127bit)
2.10.29 Code 128
Enable Code 128

- 50 -
Disable Code 128
2.10.30 Code 128 Limitation of length
Code 128 min length (1~127 bit)
Code 128 max length (1~127 bit)
2.10.31 GS1-128(requires CODE 128 to be enable)
Enable GS1-128
G
Disable GS1-128
2.10.32 ISBT-128(Not enable)

- 51 -
2.10.33 Plessey(Not enable)
Enable Plessey (default)
Disable Plessey
2.10.34 Plessey Limitation of length(Not enable)
Plessey Min Length(1~127 bit)
Plessey Max Length (1~127 bit)
2.10.35 Plessey check bit optional(Not enable)
Disable ISBT 128(Not enable)
Enable ISBT 128 (Not enable)

- 52 -
Plessey Don’t Check
Plessey Check Anf Send Check Bit
Plessey Check Don’t Send Check Bit (Default)
2.10.36 MSI plessey(Not enable)
Enable MSI Plessey (Default)
Disable MSI Plessey
2.10.37 MSI plessey Limitation of length(Not enable)
MSI Plessey Min Length (1~127 bit)
MSI Plessey Max Length (1~127 bit)

- 53 -
2.10.38 MSI plessey check bit output (Not enable)
MSI Plessey Check Bit Output
MSI Plessey Check Bit Don’t Output (Default)
2.10.39 MSI plessey Check mode selection setting
MSI Plessey Don’t Check
MSI Plessey One Check Bit MOD10 (Default)
MSI Plessey Two Check Bit MOD10/MOD10
MSI Plessey Two Check Bit MOD10/MOD11

- 54 -
2.10.40 UPC-A
Enable UPC-A
Disable UPC-A
2.10.41 UPC-A check bit
Send UPC-A Check Bit (Default)
Don’t Send
UPC-A Check Bit
2.10.42UPC-A to EAN-13(Not enable)
Enable UPC-A to EAN-13

- 55 -
Disable UPC- A To EAN-13 (Default)
2.10.43 UPC-E
Enable UPC-E
Disable UPC-E
2.10.44 UPC-E check bit
Send UPC-E Check Bit (Default)
Don’t Send UPC-E Check Bit
2.10.45 UPC-E expand UPC-A
Enable UPC-E Expand UPC-A
Disable UPC-E Expand UPC-A (Default)

- 56 -
2.10.46 EAN/JAN-8
Enable
EAN/JAN-8
Disable EAN/JAN-8
2.10.47 EAN/JAN-13
Enable
EAN/JAN-13
Disable EAN/JAN-13
2.10.48 UPC/EAN/JAN extra-code(Not enable)
Ignore UPC/EAN/JAN Extra-Code (Default)
Decode UPC/EAN/JAN Extra-Code

- 57 -
Adapt UPC/EAN/JAN Extra-Code
2.10.49 EAN13 to ISBN
Enable EAN13 To ISBN
Disable EAN13 To ISBN (Default)
2.10.50 EAN13 to ISSN(Not enable)
Enable EAN13 To ISSN
Disable EAN13 To ISSN(Default)
2.10.51 GS1 DataBar(RSS14)(Stacked)

- 58 -
Enable GS1 DataBar
Disable GS1 DataBar
2.10.52 GS1 DataBar(RSS14)(Stacked) AI(01)character send(Not enable)
Send AI(01)Character (Default)
Don’t Send AI(01)
Character
2.10.53 GS1 DataBar Limited
Enable GS1 DataBar Limited
Disable GS1 DataBar Limited
2.10.54 GS1 DataBar Limited AI(01)character send(Not enable)
Send AI(01)Character (Default)

- 59 -
Don’t Send AI(01)Character
2.10.55 GS1 DataBar Expanded
Enable GS1 DataBar Expanded
Disable
GS1 DataBar Expanded
2.10.56 PDF417
Enable PDF417
Disable PDF417
2.10.57 Micro PDF417
Enable Micro PDF417
Disable Micro PDF417

- 60 -
2.10.58 QR Code
Enable QR
Disable QR
Disable QR Code URL Link(Default)
Enable QR Code URL Link
2.10.59 Micro QR
Enable Micro QR
Disnable Micro QR
2.10.60 Data Matrix

- 61 -
Enable Data Matrix
Disable Data Matrix
2.11 User-defined prefix setting
Output
Enable User-Defined Prefix Output
Disable User-Defined Prefix Output (Default)
Edit
Clear All User-Defined Prefix
User-Defined Prefix

- 62 -
(Please follow the barcode type ID table and data and edit barcode in the appendix after scanning)
2.12 User-defined suffix setting
Output options
Disable User-Defined Suffix Output
Disable User-Defined Suffix Output (Default)
Edit
Clear All User-Defined Suffixes
User-Defined Suffix
(Please follow the barcode type ID table and data and edit barcode in the appendix after scanning)
2.13 Barcode prefix&suffix order selection
Prefix

- 63 -
<Prefix><CODE ID><AIM ID><User-Defined Prefix>(Default)
<Prefix><User-Defined Prefix><CODE ID><AIM ID>
Suffix
<User-Defined Suffix><CODE ID><AIM ID><Suffix> (Default)
<CODE ID><AIM ID><User-Defined Suffix><Suffix>
2.14 Code ID setting
Output options
Disable CODE ID (Default)
Enable CODE ID Former Barcode

- 64 -
Disable CODE ID Latter Barcode
Edit
User-Defined CODE ID
(Please follow the barcode type ID table and data and edit barcode in the appendix after scanning)
Clear All User-Defined CODE ID
2.15 AIM ID setting
Disable Barcode AIM ID (Default)
Enable Former Barcode AIM ID

- 65 -
Enable Latter Barcode AIM ID
Appendix
Appendix 1 Data and edit barcode
0

- 66 -
1
2
3
4
5
6
7

- 67 -
8
9
A
B
C
D
E

- 68 -
Appendix 2 Barcode type ID table
Barcode type
HEX
CODE ID(default)
All code system
99
Codabar
61
a
Code128
6A
j
F
Cancel a string of data read before
Cancel current setting
Cancel a string of data read before
Save

- 69 -
ISBT-128
6A
j
Code32
3C
<
Code93
69
i
Code39
62
b
Code11
48
h
Plessey
70
(Not enable)
MSI plessey
6D
(Not enable)
EAN-13
64
d
EAN-8
64
D
GS1 DataBar(RSS14)
(Stacked)
52
y
GS1 DataBar Limited
52
{
GS1 DataBar Expanded
52
}
GS1-128 (EAN-128)
6A
I
2 of 5
Interleaved 2 of 5
65
e
Matrix 2 of 5
76
m

- 70 -
Industry 2 of 5
44
f
Stamdard 25
73
(Not enable)
UPC-A
63
c
UPC-E
63
E
ISBN
42
d
ISSN
6E
(Not enable)
DataMatrix
75
w
PDF417
72
r
Micro PDF417
53
R
QR Code
51
S
Micro QR Code
51
S

- 71 -
Barcode type
AIM ID
Description
All code system
Codabar
]Fm
m:0~1
Code128
]C0
m:0,1,2,4
ISBT-128
]C4
]CD
Code32
]A0
]XD
Code93
]G0
Code39
]Am
m:0,1,3,4,5,7
Code11
]Hm
m:0,1,3,8,9
Plessey
]P0
(Not enable)
MSI plessey
]Mm
(Not enable)
EAN-13
]Em
m:0,1,3,4
EAN-8
]Em
m:0,1,3,4
GS1 DataBar(RSS14)
(Stacked)
]e0
GS1 DataBar Limited
]em
]eD
GS1 DataBar Expanded
]em
]e0
GS1-128 (EAN-128)
]C1

- 72 -
2 of 5
Interleaved 2 of 5
]Im
m:0,1,3
Matrix 2 of 5
]X0
Industry 2 of 5
]S0
Stamdard 25
]Rm
(Not enable)
UPC-A
]Em
m:0,3
UPC-E
]Em
m:0,3
ISBN
]X0
]ED
ISSN
]X0
(Not enable)
DataMatrix
]dm
m: 0~6
PDF417
]Lm
m: 0~5
Micro PDF417
]Lm
m: 0~5
QR Code
]Qm
m: 0~6
Micro QR Code
]Qm
m: 0~6

- 73 -
Appendix 3 Invisible character ASCII table
10 hex
Hex
Corresponding character
0
00
NUL
1
01
SOH
2
02
STX
3
03
ETX
4
04
EOT
5
05
ENQ
6
06
ACK
7
07
BEL
8
08
BS
9
09
HT
10
0A
LF
11
0B
VT
12
0C
FF
13
0D
CR
14
0E
SO
15
0F
SI
16
10
DLE
17
11
DC1

- 74 -
18
12
DC2
19
13
DC3
20
14
DC4
21
15
NAK
22
16
SYN
23
17
ETB
24
18
CAN
25
19
EM
26
1A
SUB
27
1B
ESC
28
1C
FS
29
1D
GS
30
1E
RS
31
1F
US

- 75 -
Appendix 4 Visible character ASCII table
10 hex
Hexadecima
l
Character
10 hex
Hexadeci
mal
Charac
ter
10 hex
Hexadecima
l
Charact
er
32
20
<SPACE>
64
40
@
96
60
`
33
21
!
65
41
A
97
61
a
34
22
“
66
42
B
98
62
b
35
23
#
67
43
C
99
63
c
36
24
$
68
44
D
100
64
d
37
25
%
69
45
E
101
65
e
38
26
&
70
46
F
102
66
f
39
27
‘
71
47
G
103
67
g
40
28
(
72
48
H
104
68
h
41
29
)
73
49
I
105
69
i
42
2A
*
74
4A
J
106
6A
j
43
2B
+
75
4B
K
107
6B
k
44
2C
,
76
4C
L
108
6C
l
45
2D
-
77
4D
M
109
6D
m
46
2E
.
78
4E
N
110
6E
n
47
2F
/
79
4F
O
111
6F
o
48
30
0
80
50
P
112
70
p

- 76 -
49
31
1
81
51
Q
113
71
q
50
32
2
82
52
R
114
72
r
51
33
3
83
53
S
115
73
s
52
34
4
84
54
T
116
74
t
53
35
5
85
55
U
117
75
u
54
36
6
86
56
V
118
76
v
55
37
7
87
57
W
119
77
w
56
38
8
88
58
X
120
78
x
57
39
9
89
59
Y
121
79
y
58
3A
:
90
5A
Z
122
7A
z
59
3B
;
91
5B
[
123
7B
{
60
3C
<
92
5C
\
124
7C
|
61
3D
=
93
5D
]
125
7D
}
62
3E
>
94
5E
^
126
7E
~
63
3F
?
95
5F
_

- 77 -

- 78 -
Appendix 5 Default setting table
Parameter name
Default setting
Remarks
Communication settings
TTL-232
(default)
Serial port baud rate
9600
Serial check bit
No check bit
Serial data bit
8 bit
Serial port stop
1 bit
Host mode
OFF
USB
USB Keyboard layout
American keyboard
Barcode content contains carriage
enter character feed processing(USB
keyboard)
0D only (enter character
CR) Tab
Case conversion
Not converting
virtual keyboard
Off
USB keyboard sending speed
Fast speed
Control character escape output
combination control key
Off
Chinese character output mode
English/Latin-1 code
Invoice function off
Mode parameter
Default reading mode
Self-induction mode
Manual mode, sensing
mode
Self-induction mode
Recode detection interval
500ms

- 79 -
Trigger condition
sensing
Lighting and aiming
Lighting mode
Normal mode
Aiming mode
Normal mode
Prompt output
Power on tone
on
Decoding success
tone
prompt
on
Beep type
audio rate low
Beep volume
high
Beep duration
long
code read tone setting
Allow
Decoding success LED prompt
On
Data editing
Prefix and suffix
Prefix adding
No add
Prefix content
No
AIM ID
No add
Code ID
No add
Suffix adding
No add
Suffix content
No

- 80 -
End character adding
Add
End character content
0x0A,0×0D
Enter
Parameter name
Default setting
Remark
Barcode symbol parameter
Inverted barcode reading
Open
Valid for all bar code
symbol types
Code 128
Reading
Allow
Max length
127
Min length
1
GS1
-
128
(
U
CC
/
EA
N
-
128
)
Reading
Allow
Max length
127
Min length
1
EAN
-
8
Reading
Allow
EAN
-
13
Reading
Allow

- 81 -
2 bit extension code
No reading
5 bit extension code
No reading
must have the extension code
No require
ISSN
Reading
Not allow
ISBN
Reading
Not allow
UPC-E
Reading
allow
Output check character
Output
Expand to
U
P
C
-
A
No expand
UPC-A
Reading
allow
Output check character
Output
UPC-A to EAN-13
Off
Interleaved 2 of 5
Reading
allow

- 82 -
Check
No check
Max length
128
Min length
4
M
a
t
r
i
x
2
o
f
5
Read
Not allow
Max length
128
Min length
4
Industrial 2 of 5
Reading
allow
Max length
128
Min length
4
S
t
a
n
da
r
d
2
o
f
5
Reading
allow
Check
No check
Output check character
No output
Max length
128
Min length
4

- 83 -
Code 39
Reading
allow
Check
No check
Output check character
No output
Support
F
u
ll
A
S
C
II
Support
Default (off)
Max length
127
Min length
1
Code 32
Reading
allow
Codabar
Reading
allow
Check
No check
Send start character and end character
No output
Max length
127
Min length
1
Code 93
Reading
allow

- 84 -
Max length
127
Min length
1
G
S
1
D
a
t
aba
r
(
RSS14
)
(Stacked)
Reading
allow
send
A
I(
01
)
character
Send
G
S
1
D
a
t
aba
r Limited
Reading
allow
Send
A
I(
01
)
character
Send
G
S
1
D
a
t
aba
r Expanded
reading
allow
Code 11
reading
allow
Check bit
Output
Off
Check bit option
Off
Max length
127
Min length
1
Plessey

- 85 -
reading
Allow
Check bit
Check but don’t
output
Max length
127
Min length
1
MSI
-
P
l
e
ss
ey
Reading
allow
Output check
Don’t output
Check bit mode selection
1 bit MOD10
Max length
127
Min length
1
PDF417
Reading
allow
Max length
2710
Min length
1
Micro PDF417
Reading
allow
Max length
2710

- 86 -
Min length
1
QR Code
Reading
allow
Max length
7089
Min length
1
Micro QR
Reading
allow
Max length
7089
Min length
1
D
a
t
a
M
a
t
r
i
x
Reading
allow
Max length
3116
Min length
1

- 87 -
Appendix 6 operational character (USB keyboard)
10 hex
Hex
Corresponding key value (disable CODE ID)
Corresponding key value (enable
CODE ID)
0
00
retain
Ctrl+@
1
01
Insert
Ctrl+A
2
02
Home
Ctrl+B
3
03
End
Ctrl+C
4
04
Delete
Ctrl+D
5
05
PageUp
Ctrl+E
6
06
PageDown
Ctrl+F
7
07
ESC
Ctrl+G
8
08
Backspace
Backspace
9
09
Tab
Tab
10
0A
Enter (The configuration of CRLF processing
decide how it express)
Ctrl+J
11
0B
Caps Lock
Ctrl+K
12
0C
Print Screen
Ctrl+L
13
0D
Enter (The configuration of CRLF processing
decide how it express)
Enter
14
0E
Scroll Lock
Ctrl+N
15
0F
Pause/Break
Ctrl+O

- 88 -
16
10
F11
Ctrl+P
17
11
Direction key ↑
Ctrl+Q
18
12
Direction key ↓
Ctrl+R
19
13
Direction key ←
Ctrl+S
20
14
Direction key →
Ctrl+T
21
15
F12
Ctrl+U
22
16
F1
Ctrl+V
23
17
F2
Ctrl+W
24
18
F3
Ctrl+X
25
19
F4
Ctrl+Y
26
1A
F5
Ctrl+Z
27
1B
F6
ESC
28
1C
F7
Ctrl+\
29
1D
F8
Ctrl+]
30
1E
F9
Ctrl+^
31
1F
F10
Ctrl+_

- 89 -
Appendix 7 operational character (serial port and USB-VCOM)
10 hex
Hex
Corresponding character
0
00
NUL
1
01
SOH
2
02
STX
3
03
ETX
4
04
EOT
5
05
ENQ
6
06
ACK
7
07
BEL
8
08
BS
9
09
HT
10
0A
LF
11
0B
VT
12
0C
FF
13
0D
CR
14
0E
SO
15
0F
SI
16
10
DLE
17
11
DC1

- 90 -
18
12
DC2
19
13
DC3
20
14
DC4
21
15
NAK
22
16
SYN
23
17
ETB
24
18
CAN
25
19
EM
26
1A
SUB
27
1B
ESC
28
1C
FS
29
1D
GS
30
1E
RS
31
1F
US

- 91 -
Some feature configuration instructions and examples
Example of custom prefix and suffix configuration
Configure the barcode pre/suffix by scan code. Each prefix or suffix character can be up to 10.(To
ensure that custom suffixes can be output, configure the scanner's custom pre/post suffix output option
to be turned on.)

- 92 -
Example 1.1: Add a custom prefix XYZ to all types of barcode.
Query the appendix barcode type ID table,the HEX value of all code systems is 99. Query the visible
character ASCII table,the HEX value corresponding to XYZ is 58, 59, 5A.
Scan configuration code, custom prefix,the barcode scanner will emit a "drip..drip.." two prompt,
Then scan the appendix data and edit the 9, 9, 5, 8, 5, 9, 5, A in the bar code, save, and complete the
configuration.
If you need to modify the scanned barcode before saving, you can also scan to cancel the previous data
or cancel the previous data to reconfigure.If you need to abandon this configuration in the middle,
directly scan to cancel the current settings.
Example 1.2:Add a custom prefix R to the QR code
Query the appendix barcode type ID table,the HEX value of all code systems is 51.Query the visible
character ASCII table,the HEX value corresponding to R is 58, 59, 5A.
Scan the configuration code Customize The Prefix, then scan the appendix data and edit the 5, 1, 5, 2
in the barcode to save, that is, complete the configuration.
Example 1.3:Cancel the custom prefix of the QR code
When customizing prefixes and suffixes,behind the barcode type characters are saved without adding
other characters,that is, clear the custom prefix and suffix for this type of barcode.Scan the
configuration code Customize The Suffix, then scan the appendix data and edit the 5,1 in the bar code,
save, and complete the configuration.

- 93 -
Noted:If there was a prefix added for all barcodes,the configured QR code prefix will be restored to
the prefix added for all barcodes.
If you need to clear the prefix/ suffixes added for various bar code types,please scan "Clear all custom
prefixes
" and "Clear all custom suffixes" configuration code.
Barcode length limit configuration example
When configuring the barcode minimum length limit, you must ensure that the configured minimum
length is not greater than the current maximum length configuration.Otherwise an error will be
indicated.Similarly,when configuring the barcode maximum length limit, must also ensure that the
configured maximum length is not less than the current minimum length configuration.
Example 2.1: Configuring Code 128 barcode length is 4-12 bits
Scan configuration code Code 128 minimum length limit,then scan the appendix data and edit the 4
in the bar code, save.
Scan configuration code Code 128 maximum length limit,then scan the appendix data and edit the 1,
2, and save the barcode to complete the configuration.
Example 2.2:Configure Interleaved 2 of 5 barcode length to 14 bits
Configuring 14 bits of Interleaved 2 of 5 barcode length can scan directly and configure ITF25 14 bits
of barcode lengths for configuration.It can also be configured by the maximum and minimum length
of the barcode:
Scan configuration code Interleaved 2 of 5 minimum length limit,then scan the appendix data and edit
the 1, 4 in the bar code, save.
Scan configuration code Interleaved 2 of 5 maximum length limit,then scan the appendix data and
edit the 1, 4 in the bar code, save,the configuration is completed.

- 94 -
Example 2.3:Configure Code 39 barcode length to any length supported.
Scan configuration code Code 39 minimum length limit,then scan the appendix data and edit the 0 in
the bar code, save,
Scan configuration code Code 39 maximum length limit,then scan the appendix data and edit the 0 in
the bar code, save,the configuration is completed.
Scan configuration code Interleaved 2 of 5 maximum length limit,then scan the appendix data and
edit the 1, 4 in the bar code, save,the configuration is completed.
Example for USB keyboard send speed configuration
If the performance of the client PC is weak and the transmission error is easy to occur, you need to
customize the USB keyboard transmission speed to a slower speed, such as 50ms:
Scan the configuration code Customize the sending speed, then scan the appendix data and edit the
5,0 in the barcode to save the configuration.
Set method of a single reading time modification
Example: Set the length of a single reading to 5.0s. Please read the following barcodes in order:
1. Read “Modify the length of a single reading”.
2. Read the data code "5" and "0".
3. Read “Save”
Produkt Specifikationer
Mærke: | Adesso |
Kategori: | Stregkodelæser |
Model: | NuScan 2800U |
Har du brug for hjælp?
Hvis du har brug for hjælp til Adesso NuScan 2800U stil et spørgsmål nedenfor, og andre brugere vil svare dig
Stregkodelæser Adesso Manualer
25 Juli 2025
25 Juli 2025
25 Juli 2025
25 Juli 2025
24 Juli 2025
24 Juli 2025
20 August 2024
19 August 2024
19 August 2024
18 August 2024
Stregkodelæser Manualer
- Godex
- Code
- Approx
- Deltaco
- Olympia
- Inateck
- ELO
- Motorola
- Nilox
- Newland
- ZBA
- Wasp
- Atlantis Land
- Argox
- DENSO
Nyeste Stregkodelæser Manualer
28 August 2025
27 August 2025
27 August 2025
25 August 2025
15 August 2025
15 August 2025
15 August 2025
14 August 2025
14 August 2025
12 August 2025