AFX Noah NOAP3010MBDG Manual

AFX Lys Noah NOAP3010MBDG

Læs gratis den danske manual til AFX Noah NOAP3010MBDG (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om AFX Noah NOAP3010MBDG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

E26 door Luminaires In

Ceiling Mount - Pendant

120VAC 60Hz/

Page 1 of 1 R0 8061539

Model #: NOAP3010MBDG

Limited Factory Warranty

AFX Inc. hereby warrants that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years

from date of purchase. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due to improper

installation, misuse, mishandling or damage incurred in transit.

View shown for reference

only. Individual models may

vary.

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal

electric shock and/or property damage.

 It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.

 Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

 This xture is designed for use in a 120 , 60Hz circuit. VAC 50/

 Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground

wire (green) contact between this xture and the ground connection of your main power supply panel.

 This xture is intend neral indoor lighting in dry or damp locations. ed to be used for ge

Assembly Instructions

Step 1 Preparing for installation–

A. at fuse or circuit breaker box before installing or servicing any Disconnect electrical power

part of this xture.

B. Carefully remove the xture from the carton, remove components from hardware kit.

C. Remove mounting bracket (1) from the xture (3) by removing four side screws (4).

D. Install mounting bracket (1) to the junction box (not included) using two screws (2) to secure

it.

Wiring All wiring must take place inside junction box (not included) –

Caution: Make sure power is o at fuse or circuit breaker box. Check power wires for

damage or scrapes. Use wire suitable for at least 90°C (194°F). Most dwellings built Note:

before 1985 have supply wire rated to 60°C. Consult a qualied electrician to ensure correct

branch circuit conductor before installing.

Step 2 Wiring xture –

A. Make all wire connections to appropriate wire. Secure with wire nuts (provided).

B. Connect the green wire from the xture to the supply power source ground wire.

C. Connect the white wire from the xture to the white (N) wire from supply power source.

D. Connect the black wire from the xture to the black (L) wire from supply power sourc e.

E. Pull on each wire lead to make sure connections are secure. Make certain Do not mix wires.

no bare wires are exposed outside of wire connectors. Tuck all connections neatly into the

junction box.

Step 3 Mounting –

A. Install xture by aligning both side holes over the mounting bracket then using four (3) (1)

screws (4 to secure it. )

B. Adjust chain (6) and cord as needed. Not of chain and power cord is provided. e: 60”

C. Adjust individual socket up or down as needed by turning setscrew (7) counterclockwise only

to loosen cord then push excess cord inside the canopy until desire height is achieved.

Retighten setscrew by turning clockwise to secure cord. Repeat same procedure for other

socket. Do not remove setscrew completely. Do not over tighten. te: 6 on socket for No ” cord

adjustability.

Step 4 Lamping (not included)–

A. Install A19 (E26) base type lamp under 60W max rating into socket and twist clockwise

rotation until securely snug. Repeat until all ve lamps are installed.

Step 5 Restore power at fuse or circuit breaker box –

Produkt Specifikationer

Mærke:	AFX
Kategori:	Lys
Model:	Noah NOAP3010MBDG

Har du brug for hjælp?

Hvis du har brug for hjælp til AFX Noah NOAP3010MBDG stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys AFX Manualer

AFX Bowen BWNS051412L30D1SB Manual

18 August 2025

AFX Echo ECHP4830LAJMVBK Manual

18 August 2025

AFX LED Security BWSW2400L41RB Manual

18 August 2025

AFX Ion IONS032015L30D2SN Manual

18 August 2025

AFX SPARKLING-PRO Manual

25 Juli 2025

AFX SPOT-240LED-FC Manual

25 Juli 2025

AFX ThunderLED Manual

24 Juli 2025

AFX PIXSTRIP-C Manual

24 Juli 2025

AFX WATERBAR Manual

24 Juli 2025

AFX LF200-NW Manual

24 Juli 2025

Lys Manualer

Nyeste Lys Manualer

Golden Lighting Monroe 7041-3 Manual

1 November 2025

Golden Lighting Leighton 8401-LP Manual

1 November 2025

Golden Lighting Haiden 0839-M1L Manual

1 November 2025

Golden Lighting Vaughn 3866-L Manual

1 November 2025

Golden Lighting Bijoux 1998-8 Manual

1 November 2025

Blizzard LoPro CSI Manual

1 November 2025

Golden Lighting Hines 3118-4SF Manual

1 November 2025

Blizzard ToughPAR Quadra Manual

1 November 2025

Golden Lighting Orwell 3306-FM Manual

1 November 2025

Blizzard TOURnado Sky W-DMX Manual

1 November 2025