ALM Boss Bow Two -027 Manual

ALM Ikke kategoriseret Boss Bow Two -027

Læs gratis den danske manual til ALM Boss Bow Two -027 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om ALM Boss Bow Two -027, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The Boss Bow Two is an 8 way bidirectional voltage controlled switch with 3 different control modes for routing CV or audio signals around a

system. Address mode allows for instant routing manually via the offset or external control voltage, step mode sequentially advances I/O fol-

lowing signal at the clock input and the strobe mode combines the two, holding the addressed position until the next clock pulse. The unique

features and ﬂexibility of the ‘BB2’ allow for a wide range of potential patches to be created.

MODES

Current mode is indicated by its associated LED.

Step : Advances one by one through the I/Os with every pulse at

the clock input. The offset control or CV input sets the direction of

the stepping with the reset input returning back to the ﬁrst I/O.

Strobe : Selects an I/O based on the voltage level or offset posi-

tion with respect to the clock input. Upon receiving a high gate,

selection will move to the I/O matching the current voltage level

and will hold that position until the next pulse.

Address : Selects an I/O based on the voltage level or offset posi-

tion. Address will immediately change I/Os and sweeps through

all jacks. Rising voltage moves the selection downward with

falling voltage going back to the top.

EIGHT MAPPABLE I/Os

Inputs or outputs connecting a signal route to or from the I/O jacks

on either side. I/Os accept both CV and audio. I/Os are switched by

the control section with each LED indicating the current connection.

MODE BUTTON

Switches the current operating

mode of the BBT from step to

strobe to CV address mode.

SINGLE SIGNAL I/O

Input or output connecting to or

from the I/O jacks on the right

side. Accepts both CV and audio.

CLOCK / RESET INPUTS

A clock signal advances through

I/Os in step mode and guides

CV selection in strobe mode.

Reset will return the BBT back

to the ﬁrst I/O upon receiving

a gate signal in step mode and

disables / enables the switch in

strobe and address modes.

BIPOLAR OFFSET

Adds or subtracts voltage from

the control signal. Combines

with control input for manual

control and adjustment.

CONTROL INPUT / ATTENUATOR

Voltage at this input selects

an I/O in address and strobe

modes. In step mode positive

voltage advances downwards

and negative voltage advances

upwards.

Use the attenuverter and offset

to dial in desired CV response.

http://busycircuits.com/alm027

TECHNICAL SPECIFICATIONS

Power: +12V 40ma / -12V 10ma

Size: 8HP

Depth: 38mm

ALM027 /

Boss Bow Two

LIMITED WARRANTY

From the date of manufacture

this device is guaranteed for a

period of 2 years against any

manufacturing or material

defects. Any such defects will

be repaired or replaced at the

discretion of ALM. This does not

apply to;

•Physical damage arising from

mistreating (i,e dropping, sub-

merging etc).

•Damage caused by incorrect

power connections.

•Overexposure to heat or direct

sunlight.

•Damage caused by inappropri-

ate or misuse.

•Use of incorrect or non ofﬁcial

ﬁrmware

No responsibility is implied or

accepted for harm to person

or apparatus caused through

operation of this product. By

using this product you agree to

these terms.

SUPPORT

Need help? Email your questions

to help@busycircuits.com

For additional info, downloads

and ﬁrmware updates please

visit the ALM website at

busycircuits.com

Follow @busycircuits on Twitter

and Instagram for news, tips and

ideas.

Visit ‘ALM TV’ on youtube.com

for module video tuorials and

demos.

Module Installation

With your modular synth

powered connect the 10 pin off

end of the supplied standard

eurorack power connector cable

to the 10 pin power connector on

the rear of the module.

The red stripe on the cable

should be orientated to match

the text ‘RED’ marked on the

rear of the module near the

power connector (this is -12V).

Connect the other 16 pin end of

the cable to your eurorack bus

board (Refer to your bus board

documentation for the correct

orientation).

You are now safe to power up

your modular synth. If the mod-

ule fails to power up check you

have the power cable correctly

orientated and have carefully

read this manual.

ALM027 manual version: 0.1

Input

Outputs Output Inputs

Boss Bow Two

Reset

I/OI/O

-|+

Offset

Clock

Mode

Address

Strobe

Step

Control

Produkt Specifikationer

Mærke:	ALM
Kategori:	Ikke kategoriseret
Model:	Boss Bow Two -027

Har du brug for hjælp?

Hvis du har brug for hjælp til ALM Boss Bow Two -027 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret ALM Manualer

29 August 2024

29 August 2024

29 August 2024

29 August 2024

23 August 2024

ALM Stereo Sum Manual

23 August 2024

ALM mmMidi -023 Manual

20 August 2024

ALM MCF x2 -030 Manual

16 August 2024

ALM Quaid Megaslope -020 Manual

16 August 2024

ALM S.B.G. -006 Manual

16 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ANCEL BD200 Manual

4 November 2025

Yamazen KSF-S34 Manual

4 November 2025

Hendi CombiTurbo 281277 Manual

4 November 2025

Uniprodo UNI_PBM_58 Manual

4 November 2025

Wimberley AP-603 Manual

4 November 2025

Essentiel B B-Hydro Brush Manual

4 November 2025

Cooler Master Mini 110 Manual

4 November 2025

ANCEL FX3300 ELITE Manual

4 November 2025

WALI AMM002-B Manual

4 November 2025

Eliminator Lighting Electro 64 BLED Manual

4 November 2025