Amer AMRDCP100KIT Manual

Amer Flad panel støtte AMRDCP100KIT

Læs gratis den danske manual til Amer AMRDCP100KIT (2 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Amer AMRDCP100KIT, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Installation & Assembly: Universal Drop Ceiling Mount
Model Number:
AMR 100KITDCP
IMPORTANT! Read instruction sheet be-
fore you start installation and assembly.
Before you start make sure all parts listed
are included with your product.
Part # Parts Description Qty. Part Image
A M5x45 Drywall
Screw
2
Not used with 2x2 plate
B Plastic Anchor 2
Not used with 2x2 plate
C M6.5 Washer 2
Not used with 2x2 plate
D M4x16 screw 4
E M4x40 screw 4
F M6x16 screw 4
G M6x40 screw 4
H 8MM hex bolts 2
I M5x16 arm screw 4
J M5 washer 4
K S=3mm Allen
wrench
1
L S=6mm Allen
wrench
1
M M5 washer 4
N Arm 4
O Universal Spider 1
Part # Parts Description Qty. Part Image
P Mount plate 1
Q Middle Piece 1
R Ceiling Plate 1
SCaddy® Speed Link 1
T Hold Down Clips 2
Parts List
www.amer.com For assistance, call 1-800-241-1644
Step 1
Decide where you want to hang your projector in the ceiling.
Remove the existing ceiling tile and place the 2’x2’ plate in the
ceiling using the best orientation for your alignment.
Step 2
Select the location hole to run wires and cables from the ceil-
ing. Plug the four other holes with the provided plugs.
Use two 8mm hex bolts (H) to attach mount plate (P) to ceiling
plate (R).
hex bolt hex bolt
Step 3
Insert two Y-Toggles (S) through two of the sixteen slots on
the back of the ceiling plate (R) and wrap cable over rafter or
ceiling grid as shown:
Step 4
Push Hold Down Clips (T)
down to snap over t-bar as
shown:
Step 5
Attach the three or four arms (M) to the universal spider (N) using
the screws (H) and washers (I) & (L). Do not completely tighten
the screws yet.
Step 6
Attach your projector to the arms (M). Several different screw sizes
sure all screws from step 3 are tightened.
Step 7
Carefully hook the universal spider (N)
with your projector attached to the ceiling.
Installation is now complete.
Adjustment
You can change the tilt of your mount by carefully moving it to the
desired position. You may need to tighten the two tilt adjustment
screws to hold the projector in place.
screws using the allen wrench. Turn the projector to the desired
facing and retighten the screws.
DO NOT CONTINUALLY TURN THE PROJECTOR IN A COUN-
TER-CLOCKWISE DIRECTION! This can cause the mount to
come apart and may cause injury or damage.
swivel screw
tilt screw
swivel screw
tilt screw
www.amer.com For assistance, call 1-800-241-1644
Installation Instructions
Integ ted Cablera
Y-Toggle
Support/Safety
connection slots
(choose 2, depending
on installation)

Produkt Specifikationer

Mærke: Amer
Kategori: Flad panel støtte
Model: AMRDCP100KIT

Har du brug for hjælp?

Hvis du har brug for hjælp til Amer AMRDCP100KIT stil et spørgsmål nedenfor, og andre brugere vil svare dig


Flad panel støtte Amer Manualer

Amer

Amer AMRDCP100KIT Manual

29 August 2024

Flad panel støtte Manualer

Nyeste Flad panel støtte Manualer

Ateca

Ateca VARIATION00376 Manual

26 Februar 2025
Ateca

Ateca SILHOUETTE00383 Manual

26 Februar 2025
Ateca

Ateca ELLIPSE00381 Manual

26 Februar 2025
Ateca

Ateca SILHOUETTE00384 Manual

26 Februar 2025
Ateca

Ateca CRESCENDO00388 Manual

26 Februar 2025
Ateca

Ateca AT247BA Manual

26 Februar 2025
Ateca

Ateca LEDE00224 Manual

26 Februar 2025
Ateca

Ateca UNIQUE00335 Manual

26 Februar 2025
Ateca

Ateca LEGEND00176 Manual

26 Februar 2025
Ateca

Ateca LUXE00281 Manual

26 Februar 2025