APC Back-UPS 400 Manual

APC UPS Back-UPS 400

Læs gratis den danske manual til APC Back-UPS 400 (2 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om APC Back-UPS 400, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Back-UPS ES 400/550/700

User’s Guide

™

1Connect Battery

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The Back-UPS ES will not operate until the wire is connected to the touch

safe battery terminal.

NOTE: Small sparks may occur during battery connection. This is normal.

TURN the Back-UPS ES over and

slide the battery compartment

cover off of the battery housing.

1 2 3

LIFT the battery out of the compartment

and connect the black wire to the

negative (-) battery terminal. Ensure the

batteries are installed as shown below.

Slide the battery compartment cover

back onto the battery housing.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS ES power cord directly into a wall outlet; not a

surge protector or power strip. The wall outlet should be located near

the equipment and be easily accessible.

Connect Modem / Phone / DSL / Fax / 10/100 Base- T/HPNA to

Surge Protection.

The Back-UPS protects a single line (2-wire) phone (including Digital

Subscriber line - DSL), Home Phoneline Networking Association (HPNA)

type equipment, modem, 10/100 Base-T Ethernet, or fax machines from

surges when connected through the UPS as shown in the drawing below.

Note: Telephone Cable OR Network Cable should be connected to Surge

Protection ports. Do not connect the UPS surge protection ports to both

Telephone and Network System cables at the same time.

Connect Computer Cable (This is applicable for 550/700 only)

The supplied cable and software provide automatic file saving and

shutdown of the operating system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS ES. Connect the other

end of the cable to the USB port on your computer. The software will

automatically find the USB Port of your computer.

2Connect Equipment

Surge Protection Only

These outlets provide full-time protection from surges even if

the Back-UPS ES is switched OFF. Plug your printer, fax

machine, scanner, or other peripherals that do not need

battery power into these outlets.

Battery Backup Surge Protection

These outlets are powered whenever the Back-UPS ES is

switched ON. During a power outage or other AC

problems (brownouts, over-voltages), these outlets will be

powered for a limited time by the Back-UPS ES. Plug your

computer, monitor, and two other data-sensitive devices

(external disk or tape drive) into these outlets.

3Power On and

Install Software

EN 990-2375A

Press the ON/OFF switch to power the unit

ON.

A single short beep and the green “Power On”

indicator confirms that Back-UPS ES is on and

ready to provide protection.

The Back-UPS ES should charge for at least

16 hours to ensure sufficient runtime. The unit

is being charged whenever it is connected to

AC power, whether the unit is turned ON or

OFF.

Install the PowerChute™ Personal

Edition software (This is applicable for

550/700 only.)

Place the PowerChute Personal Edition CD-

ROM into your computer and follow the

installation instructions on the screen.

Status Indicators

The Back-UPS ES indicates operating status using a combination of visual and audible indicators.

Use the following table to identify the status of the Back-UPS ES.

Status Visual Indications

(Power On - Green)

(Replace Battery - Red)

Audible Indication Alarm Terminates

When

Power On - UPS is supplying conditioned

AC power to the load. Power On LED - ON None Not applicable.

On Battery - UPS is supplying battery

power to the load connected to the Battery

outlets.

Power On LED - ON (off

during beep) Beeping 4 times every

30 seconds UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning - UPS is supplying

battery power to the load connected to the

Battery outlets and the battery is near

exhaustion.

Power On LED - flashing Rapid beeping (every

1/2 second) UPS transfers back to

normal operation, or

when UPS is turned off.

Replace Battery - Battery is in need of

charging or is at the end of its usual life and

must be replaced.

Power On and Replace

Battery LEDs - Flashing

(alternating)

Constant tone UPS turned off with the

power switch.

Battery Disconnected - The battery is

disconnected or bad battery. Replace Battery LED -

flashing Constant tone UPS turned off with the

power switch.

Overload Shutdown - During On Battery

operation a battery power supplied outlet

overload was detected.

None Constant tone UPS turned off with the

power switch.

Sleep Mode - During On Battery operation

the battery power has been completely

exhausted and the UPS is waiting for AC

power to return to normal.

None Beeping once every 4

seconds. AC power is restored, or

if AC power is not

restored within 32

seconds, or the UPS is

turned off.

See the Troubleshooting section for additional assistance.

2013 APC by Schneider Electric

. APC, the APC logo, Back-UPS and PowerChute are owned by Schneider Electric Industries S.A.S.,

07/2013

or their affiliated companies. All other trademarks are property of their respective owners.

DATALINE OUTPUT

TO COMPUTER USB

FROM WALL JACK

PORT (BACK-UPS ES 550

AND ES 700 ONLY)

TO DSL MODEM,

PHONE, NETWORK

(10/100 Base-T)

bu366a

CIRCUIT BREAKER

PUSH TO RESET

bu365d

POWER ON/

REPLACE BATTERY

INDICATOR

AC LINE

CORD

Produkt Specifikationer

Mærke:	APC
Kategori:	UPS
Model:	Back-UPS 400

Har du brug for hjælp?

Hvis du har brug for hjælp til APC Back-UPS 400 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

UPS APC Manualer

APC RBC150 Manual

2 April 2025

APC RBC151 Manual

2 April 2025

APC Symmetra LX 4kVA Manual

30 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

30 Januar 2025

30 Januar 2025

APC BE650G2-IT Manual

14 Januar 2025

UPS Manualer

Nyeste UPS Manualer

Teltonika BAT120 Manual

30 Januar 2025

LevelOne UPS-2101 Manual

9 Januar 2025

Conceptronic ZEUS52E6K Manual

31 December 2025

Conceptronic ZEUS51E6K Manual

31 December 2025

CyberPower Smart App Sinewave PR2000RT2U Manual

30 December 2025

Tripp Lite ECO750UPS Manual

30 December 2025

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/10 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/20 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/ 5 Manual

28 December 2024

Conceptronic ZEUS52EA3K Manual

14 December 2024