APC Mobile Power Pack M12USWH Manual

APC power bank Mobile Power Pack M12USWH

Læs gratis den danske manual til APC Mobile Power Pack M12USWH (2 sider) i kategorien power bank. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om APC Mobile Power Pack M12USWH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

User Manual

Mobile Power Pack M12USWH

Charge USB Devices

Charge devices using the original

USB cable that comes with the

unit, or another USB charging

cable.

Connect the mobile power pack

with the device to be charged and

press the POWER button for

about 1 second.

Charge the Power Pack

Inventory Safety and General

Information

Read this user manual carefully

before using the product, and

keep it for future reference.

• Do not short circuit this device. To avoid short

circuit, keep the device away from any metal

objects (e.g., hair clips and keys).

• It is normal that the battery will feel warm

during heavy use.

• Use this device as instructed to avoid electric

shock; do not disassemble.

• This unit is not user repairable; contact APC for

tech support related issues.

• CAUTION

RISK OF FIRE AND BURNS.

Do not open, crush, heat above 40°C or

incinerate. Follow manufacturer's instructions.

• During normal usage keep the device out in the

open to allow excess heat to dissipate.

• Charge M12USWH for 2.5 hours before initial

use.

• Keep the USB output port and micro-USB input

port clean and free of obstruction.

Failure to follow these instructions can result in

equipment damage.

Use the included charging cable

to connect the USB output port

of a USB charger or PC to the

micro-USB input port on the

power pack. (Note: some PCs in

sleep mode do no provide output

power to the USB port)

By USB charger By PC

LED Status Indicators

To check the remaining battery

charge of this device in standby

mode, press the POWER button

for about 1 second. The battery

capacity display will display

ho w mu ch ba ttery p owe r is

remaining

Indicator

Status Battery Full Battery

charging

Battery

inserted into

the UPS

Fault detected

on USB ports

Mobile

Power Pack

LEDs

All 5 LEDs

illuminate green

LEDs indicate

charge level.

Top LED

flashes.

One LED

illuminates

green from

bottom to top

All 5 LEDs

flash green

001

Front View

002

Rear View

POWER button

1.0A USB port

2.4A USB port

Capacity Indicator LEDs

UPS connector (for use with BGE50ML only)

Micro-USB input

User Manual

USB cable

81-100%

61-80%

41-60%

21-40%

0-20%

Note: The charge times in this table

are approximate figures.

Device M12USWH

Smartphone 5x

Tablet ~ 1x

Electric Industries S.A.S., or their affiliated companies. All other trademarks are

property of their respective owners.

EN 990-9674

03/2015

Using the mobile power pack with a UPS

This mobile power pack can be plugged into the APC Back-UPS

Connect BGE50ML to provide AC power backup for low power

networking equipment and also DC power via USB. The fastest way

to charge the mobile power pack is to charge it inside the UPS where

it will fully charge the battery in 2.5 hours. Simply insert the battery

into the opening in the front of the UPS. The battery can only go in

one direction, with the LEDs on top and USB ports on the bottom.

When plugged in the mobile power pack charges much faster than

when using the standard micro-USB input. To remove the mobile

power pack, simply pull the battery out.

Troubleshooting

Specifications

*1 The two (2) USB ports combined have a maximum output of

3.4A. If two (2) devices together draw more than 3.4A, overload

protection circuits will trigger and disable output.

APC by Schneider Electric IT

Customer Support Worldwide

For country specific customer support, go to the APC by

Schneider Electric Web site, www.apc.com.

Problem and Possible Cause Solution

The mobile power pack cannot be charged.

The PC is in sleep mode. Wake PC from sleep mode.

The temperature is outside of the recommended

temperature range for use. Stop using the mobile power pack until it is within the correct

temperature range.

The charging cable is malfunctioning. Carefully check if the charging cable is functioning. Clean the micro-

USB port in case there is an obstruction.

The mobile power pack cannot charge some devices.

The mobile power pack is not powered on. Press the POWER button on the mobile power pack.

The remaining capacity of the mobile power pack

is low. Charge the mobile power pack.

The mobile power pack’s automatic load detection

has detected no load and has powered off the unit. Press the POWER button on the mobile power pack.

The mobile power pack does not recognize or

detect the devices connected to it. Remove connected devices. Turn the unit on, reconnecting each

device one at a time. Some devices may require a dedicated charging

cable. The cable included with this device is a standard data cable.

The mobile device has overloaded the USB port or

a short circuit has occurred in the mobile device

connected to the mobile power pack.

When the USB port encounters an error such as overload or a short,

the mobile power pack will flash all LEDs. If the error is not

removed the mobile power pack will enter into safe mode after 30

seconds. To deactivate safe mode, disconnect all devices from the

mobile power pack press the POWER button or connect the mobile

power pack to a USB charger as if charging.

The life of the mobile power pack has expired or a

fault has been detected. In the case where a system fault has been detected, contact your local

APC by Schneider Electric dealer or authorized APC by Schneider

Electric service agency.

Type Lithium-ion battery

Capacity 11400mAh

Rating 41.2 Wh

Input current (Maximum) micro-USB: 2.1A

Rated input voltage 5V dc

Output current USB1: 2.4A, USB2: 1.0A

Output voltage 5V

Capacity indicator light 5 level LEDs

Capacity indicator

brightness levels 50% in the UPS. As mobile power

pack 100% after pressing the POWER

button. 10% after 20 seconds when

charging a device or being charged.

Charging time 2.5 hours (UPS), 8 hours (micro-USB)

Dimensions (L x W x H) 5.1 x 2.9 x 0.9 in (13.0 x 7.4 x 2.2 cm)

Weight 0.6 lb (267g)

Operating temperature 32°F- 104°F (0°C- 40°C)

Smart Charging (2.4A

port only) Maximum output depends on the

client device.

u42

bu4

24a

Battery Recycling

Information

Always dispose of used or spent batteries

properly.

Return the spent battery to an appropriate

facility for proper disposal and recycling.

Warranty

Schneider Electric IT (SEIT) warrants its products

to be free from defects in materials and

workmanship for a period of three (3) years from

the date of purchase. SE IT obligation under this

warranty is limited to repairing or replacing, at its

sole discretion, any such defective products. This

warranty does not apply to battery wear from use,

equipment that has been damaged by accident,

negligence or misapplication or has been altered

or modified in any way. SEIT standard procedure

is to replace the original unit with a factory

reconditioned unit. Customers who must have the

original unit back due to the assignment of asset

tags and set depreciation schedules must declare

such a need at first contact with an SEIT Technical

Support representative. SEIT will ship the

replacement unit once the defective unit has been

received by the repair department, or cross ship

upon the receipt of a valid credit card number. The

customer pays for shipping the unit to SEIT. SEIT

pays ground freight transportation costs to ship the

replacement unit to the customer. For full warranty

information refer to www.apc.com.

Produkt Specifikationer

Mærke:	APC
Kategori:	power bank
Model:	Mobile Power Pack M12USWH
Bredde:	130 mm
Dybde:	74 mm
Højde:	23 mm
Vægt:	270 g
Brugervejledning:	Ja
Produktfarve:	Hvid
Batterikapacitet:	11400 mAh
Pakkevægt:	330 g
Pakkedybde:	125 mm
Pakkebredde:	164 mm
Pakkehøjde:	27 mm
Batteriteknologi:	Lithium-Ion (Li-Ion)
Automatisk slukning:	Ja
Kabler inkluderet:	Micro-USB
Indgangseffekt:	10 W
Certificering:	cTUVus, EN 55022 Class A, EN 55024, EN 61000-3-2, EN 61000-3-3, EN 61000-4-8, EN61000-4-2, EN61000-4-3, FCC Part 15 Class B, ICES-003, UN 38.3
LED-indikatorer:	Status
Udgangsspænding:	115 V
Indgangsspænding:	88 - 142 V
Opladningskilde:	USB
Antal enheder der er tilsluttet samtidigt (maks.):	2
Oplader, kompabilitet:	Mobile phone/Smartphone,Tablet,MP3/MP4,GPS,E-book reader
USB A udgangsporte:	2
Form:	Firkant
Opladningstid for basis enheden:	2.5 t