APC Smart-UPS SRT96BP Manual

APC UPS Smart-UPS SRT96BP

Læs gratis den danske manual til APC Smart-UPS SRT96BP (16 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11 anmeldelser. Har du et spørgsmål om APC Smart-UPS SRT96BP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Installation Guide Smart-UPS™ On-Line

External Battery Pack SRT96BP/72BP

Important Safety Messages

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during

installation and maintenance of the Smart-UPS and batteries.

Read these instructions carefully and look at the equipment to become familiar with the device before trying to install,

operate, service or maintain it. The following special messages may appear throughout this bulletin or on the equipment

to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of this symbol either to a “Danger” or “Warning” safety label indicates that an electrical

hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury or death.

Product Handling Guidelines

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate

injury.

NOTICE

NOTICE is used to address practices not related to physical injury.

<18 kg

<40 lb

18-32 kg

40-70 lb

32-55 kg

70-120 lb

>55 kg

>120 lb

Smart-UPS On-Line External Battery Pack SRT96BP/72BP2

Safety and General Information

• Adhere to all national and local electrical codes.

• Changes and modifications to this unit not expressly approved by APC by Schneider Electric could void the

warranty.

• This unit is intended only for indoor use in a controlled environment.

• Do not operate this unit in direct sunlight, in contact with fluids, or where there is excessive dust or humidity.

• Be sure the air vents on the unit are not blocked. Allow adequate space for proper ventilation.

• The battery typically lasts for three to five years. Environmental factors impact battery life. Elevated ambient

temperatures, poor quality mains power, and frequent short duration discharges will shorten battery life.

• The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.

• The batteries are heavy. Remove the batteries before installing the UPS and external battery packs (XLBPs) in a

rack.

• Always install XLBPs at the bottom in rack-mount configurations. The UPS must be installed above the XLBPs.

• The UPS will recognize as many as 10 XLBPs connected to the UPS.

Note: For each XLBP added, increased recharge time will be required.

• Always recycle used batteries.

• Recycle the package materials or save them for reuse.

• Additional safety information can be found in the Safety Guide supplied with this unit.

Battery safety

• Replace batteries with the same number and type of batteries as originally installed in the equipment.

• Schneider Electric uses Maintenance-Free sealed Lead Acid batteries. Under normal use and handling, there is

no contact with the internal components of the battery. Over charging, over heating or other misuse of batteries

can result in a discharge of battery electrolyte. Released electrolyte is toxic and may be harmful to the skin and

eyes.

• CAUTION: Before installing or replacing the batteries, remove jewelry such as wristwatches and rings.

High short circuit current through conductive materials could cause severe burns.

• CAUTION: Do not dispose of batteries in a fire. The batteries may explode.

• CAUTION: Do not open or mutilate batteries. Released material is harmful to the skin and eyes and may be

toxic.

Overview

• To verify that installation of an external battery pack (XLBP) has been successful, go to the UPS display

interface.

Perform a Visible Alarm Test to determine if the XLBP is recognized by the UPS.

The LED on the XLBP will flash if successful communication has been established.

• When viewing the status of an XLBP on the UPS display interface screen, the LED on the corresponding XLBP

will flash.

• When an RBC needs to be replaced, perform a Runtime Calibration Test to verify that battery replacement is

required.

Produkt Specifikationer

Mærke:	APC
Kategori:	UPS
Model:	Smart-UPS SRT96BP

Har du brug for hjælp?

Hvis du har brug for hjælp til APC Smart-UPS SRT96BP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

UPS APC Manualer

APC RBC150 Manual

2 April 2025

APC RBC151 Manual

2 April 2025

APC Symmetra LX 4kVA Manual

30 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

30 Januar 2025

30 Januar 2025

APC BE650G2-IT Manual

14 Januar 2025

UPS Manualer

Nyeste UPS Manualer

Teltonika BAT120 Manual

30 Januar 2025

LevelOne UPS-2101 Manual

9 Januar 2025

Conceptronic ZEUS52E6K Manual

31 December 2025

Conceptronic ZEUS51E6K Manual

31 December 2025

CyberPower Smart App Sinewave PR2000RT2U Manual

30 December 2025

Tripp Lite ECO750UPS Manual

30 December 2025

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/10 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/20 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/ 5 Manual

28 December 2024

Conceptronic ZEUS52EA3K Manual

14 December 2024