APC XB005XPDR Manual

APC UPS XB005XPDR

Læs gratis den danske manual til APC XB005XPDR (2 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om APC XB005XPDR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Safety and General Instructions

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should

be followed during installation and maintenance of the product.

Read the user documentation to become familiar with the equipment before

trying to install or operate it.

• While disconnecting wires, be sure to disconnect the wires at battery pack(s) first and

then at the power supply unit.

• Always connect the wires to the power supply unit first and then to battery pack(s).

• Use RED color wire for +ve and BLACK color wire for –ve connections.

• Use insulated pin type lugs to be sure that the wire strands do not touch any metallic

surface during connection/disconnection.

• Be sure that the wires do not touch any metallic surface during

connection/disconnection.

• Allow minimum space of 50 mm above the battery pack and 180 mm below the battery

pack and 10 mm lateral distance from other devices to be sure of sufficient cooling.

• CAUTION: The enclosure can reach temperatures that exceed the burn thresholds for

touchable surfaces, depending on the ambient temperature and load.

• Do not introduce any objects into the device.

Specifications

Environmental

Physical

Battery

Certification and Standards

IEC/EN/BS/UL 62368-1, CSA-C22.2 No. 62368-1, IEC/EN 60950-1, CE, UKCA, cTUVus

Front Panel Features

Installation

Mounting

NOTE: Be sure that the input/output terminal blocks are at the top while mounting the

power supply unit on a 35 mm DIN rail.

1. Locate the top hooks of the rail

mounting system (on the battery

pack) with the unit slightly tilted

upwards.

2. Rotate the unit in clockwise

direction till the latch of the rail

mount system snaps on to the

DIN rail and the battery pack

cannot be rotated any further.

3. Shake the battery pack slightly

to be sure that it is securely

mounted on the DIN rail.

Dismounting

1. Release the latch of the rail

mount system (on the battery

pack) by pulling it downwards

using a screw driver.

2. Tilt the battery pack upwards till

the latch is free from the DIN

rail.

3. Slide the battery upwards till the

top hooks gets free from the

DIN rail.

Connect Battery Pack to the power supply unit

Recommended wire sizes and tightening torque

NOTE:

• Be sure to use a Pin Type cable lug for connecting the Input,

Output and Battery wires.

• To be sure of a secure connection, the wire insulation should be

stripped (S) for approx. 6 mm,

Be sure that all the strands are completely enclosed in the lug.

• Be sure to connect the wires first to the terminals on the power

supply unit and then to the terminals on the battery pack(s).

• Be sure that the positive and negative polarity wires are connected to the respective

output terminals on the power supply unit.

Connect a single battery pack

Connect the battery wires to the battery terminals (refer “Front Panel Features” for details).

Connect mutiple battery packs

Connect the battery wires to the battery terminals (refer “Front Panel Features” for details).

Ambient temperature Operating –15 to +50 °C

Storage* –15 to +40 °C

Humidity 0 to 95% (Non condensing)

Altitude 3000 m (Max.)

NOTE: * Charge the battery once in every 3 months during storage or

when not in use.

Dimensions without packaging (H x W x D) 192 x 129 x 119 mm

(7.56 x 5.08 x 4.69 in)

Dimensions with packaging (H x W x D) 240 x 190 x 188 mm

(9.45 x 7.48 x 7.40 in)

Weight without packaging 4.5 kg

(9.92 lb)

Weight with packaging 4.8 kg

(10.58 lb)

Model XB005XPDR

Type SMF VRLA

Nominal Voltage 24 VDC (2 Nos. 12 V batteries connected in series)

Capacity 4.5 Ah

Over current / Short circuit protection 40 A Fuses

Charging Voltage 27.4 VDC

Charging Current 0.75 A

Maximum number of battery packs

that can be connected in parallel 4

Battery Runtime 10 minutes at 10 A load

3 minutes at 20 A load

(+) Battery terminal

(–) Battery terminal

oem0348a

oem0349a

oem0350a

CAUTION

RISK OF EQUIPMENT DAMAGE

• Wiring should be performed by a qualified electrician.

• Wire size must comply with required current capacity as well as national and local

electrical codes.

• Be sure to turn Off the input power supply before connecting or disconnecting input,

output and battery wires to the terminals.

• Be sure that the wires do not touch each other or any metal object during connection/

disconnection.

• Be sure to connect the battery wires first to the power supply unit and then to the

battery.

• Be sure to disconnect wires first from the battery and then from the power supply unit.

• Be sure to crimp pin type lugs to the input, output and battery wires to prevent loose

strands from touching any metal object.

Failure to follow these instructions can result in equipment damage and

minor or moderate injury.

Wire Size Torque

Battery 12 AWG (3.310 mm2)0.8 N m

+–+–

+–

oem0351a

BP#1 BP#2

+–

+–+–+–

oem0352a

User Manual Easy UPS DIN Rail

Mount External Battery Pack

XB005XPDR

Customer support and warranty information is available at www.se.com.

the Schneider Electric logo, are trademarks of Schneider Electric SE, its

subsidiaries or affiliated companies. All other brands may be trademarks of

their respective owners.

990-6464C

05/2022

Fuse Replacement

NOTE: Fuse replacement feature is available in battery packs manufactured after

June 2022.

Limited Factory Warranty

Schneider Electric IT Corporation (SEIT), warrants its products to be free from defects in

materials and workmanship for a period of ONE (1) year. The SEIT obligation under this

warranty is limited to repairing or replacing, at its own sole option, any such defective

products. Repair or replacement of a defective product or part thereof does not extend the

original warranty period.

This warranty applies only to the original purchaser who must have properly registered the

product within 10 days of purchase. Products may be registered online at

warranty.apc.com.

SEIT shall not be liable under the warranty if its testing and examination disclose that the

alleged defect in the product does not exist or was caused by end user or any third person

misuse, negligence, improper installation, testing, operation or use of the product contrary

to SEIT recommendations of specifications. Further, SEIT shall not be liable for defects

resulting from: 1) unauthorized attempts to repair or modify the product, 2) incorrect or

inadequate electrical voltage or connection, 3) inappropriate on site operation conditions,

4) Acts of God, 5) exposure to the elements, or 6) theft. In no event shall SEIT have any

liability under this warranty for any product where the serial number has been altered,

defaced, or removed.

EXCEPT AS SET FORTH ABOVE, THERE ARE NO WARRANTIES, EXPRESS OR

IMPLIED, BY OPERATION OF LAW OR OTHERWISE, APPLICABLE TO PRODUCTS

SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION

HEREWITH.

SEIT DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY,

SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE.

SEIT EXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR

AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, SEIT

RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION

WITH THE PRODUCTS.

THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF

ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE

CONSTITUTE SEIT'S SOLE LIABILITY AND PURCHASER EXCLUSIVE REMEDY FOR

ANY BREACH OF SUCH WARRANTIES. SEIT WARRANTIES EXTEND ONLY TO

ORIGINAL PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES.

IN NO EVENT SHALL SEIT, ITS OFFICERS, DIRECTORS, AFFILIATES OR

EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL,

CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE

OR INSTALLATION OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN

CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT

LIABILITY OR WHETHER SEIT HAS BEEN ADVISED IN ADVANCE OF THE

POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, SEIT IS NOT LIABLE FOR ANY

COSTS, SUCH AS LOST PROFITS OR REVENUE, WHETHER DIRECT OR INDIRECT,

LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS

OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BY THIRD PARTIES, OR

OTHERWISE.

NOTHING IN THIS LIMITED WARRANTY SHALL SEEK TO EXCLUDE OR LIMIT OR

DEATH OR PERSONAL INJURY RESULTING FROM ITS NEGLIGENCE OR ITS

FRAUDULENT MISREPRESENTATION OF TO THE EXTENT THAT IT CANNOT BE

EXCLUDED OR LIMITED BY APPLICABLE LAW.

To obtain service under warranty you must obtain a Returned Material Authorization (RMA)

number from customer support. Customers with warranty claims issues may access the

SEIT worldwide customer support network through the APC by Schneider Electric Web

site: www.apc.com. Select your country from the country selection drop down menu. Open

the Support tab at the top of the web page to obtain information for customer support in

your region. Products must be returned with transportation charges prepaid and must be

accompanied by a brief description of the problem encountered and proof of date and place

of purchase.

Schneider Electric Worldwide

Customer Support

Customer support for this or any other Schneider Electric product is available at no charge

in any of the following ways:

• Visit the Schneider Electric Web site to access documents in the Schneider Electric

Knowledge Base and to

– submit customer support requests.

– www.schneider-electric.com (Corporate Headquarters)

Connect to localized Schneider Electric Web sites for specific countries, each of which

provides customer support information.

– www.schneider-electric.com/support/

Global support searching Schneider Electric Knowledge Base and using e-support.

• Contact Schneider Electric IT (SEIT) Customer Support Center by telephone or

e-mail.

– Local, country specific centers: go to www.schneider-electric.com/support/contact

for contact information.

For information on how to obtain local customer support, contact the Schneider Electric

representative or other distributor from whom you purchased your Schneider Electric

product.

a. Disconnect all the wires from the battery pack.

b. Dismount the battery pack from the DIN rail. Refer to “Dismounting” on page 1 for

details.

a. Turn the battery pack upside down.

b. Locate the 3 screws securing the

cover to the chassis and unfasten

them.

Locate the 4 screws securing the cover

to the chassis and unfasten them.

Remove the cover. Pull out the fuses from the holders.

Push in the replacement fused into the

holders.

Replace the cover.

Secure the cover to the chassis by

fastening the 4 screws (unfastened in

step ).

a. Turn the battery pack upside down.

b. Secure the cover to the chassis by

fastening the 3 screws (unfastened

in step ).

a. Mount the battery pack on the DIN rail. Refer to “Mounting” on page 1 for details.

b. Connect all the wires to the battery pack (disconnected in step

).

oem

03a

oem037 9a

oem

03a

oem0

m03a

oem03a

oem

03a

oem

03a

Produkt Specifikationer

Mærke:	APC
Kategori:	UPS
Model:	XB005XPDR

Har du brug for hjælp?

Hvis du har brug for hjælp til APC XB005XPDR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

UPS APC Manualer

APC RBC150 Manual

2 April 2025

APC RBC151 Manual

2 April 2025

APC Symmetra LX 4kVA Manual

30 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

30 Januar 2025

30 Januar 2025

APC BE650G2-IT Manual

14 Januar 2025

UPS Manualer

Nyeste UPS Manualer

Teltonika BAT120 Manual

30 Januar 2025

LevelOne UPS-2101 Manual

9 Januar 2025

Conceptronic ZEUS52E6K Manual

31 December 2025

Conceptronic ZEUS51E6K Manual

31 December 2025

CyberPower Smart App Sinewave PR2000RT2U Manual

30 December 2025

Tripp Lite ECO750UPS Manual

30 December 2025

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/10 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/20 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/ 5 Manual

28 December 2024

Conceptronic ZEUS52EA3K Manual

14 December 2024