Aqua Computer cuplex kryos NEXT RGBpx AM4 Manual

Aqua Computer Ikke kategoriseret cuplex kryos NEXT RGBpx AM4

Læs gratis den danske manual til Aqua Computer cuplex kryos NEXT RGBpx AM4 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Aqua Computer cuplex kryos NEXT RGBpx AM4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

cuplex kryos NEXT RGBpx 12/2020

cuplex kryos NEXT

cuplex kryos NEXTcuplex kryos NEXT

cuplex kryos NEXT

Operating and assembly manual

Operating and assembly manualOperating and assembly manual

Operating and assembly manual

1. Preparation

1. Preparation1. Preparation

1. Preparation

Back up your data before modifying your hardware! Disconnect your PC from the mains power

outlet. To prevent damaging the sensitive hardware components, make sure to ground your

workplace and yourself to prevent electrostatic discharges.

When upgrading an existing PC setup, remove the installed heat sink from the CPU. Refer to the

instruction manual of the CPU cooler for details. Remove thermal grease residues from the CPU

surface using benzine if necessary.

Place a small drop (diameter ca. 4 mm or 0.15 inch) of thermal grease supplied with the cuplex

kryos NEXT centrally on the CPU. Alternatively, you can apply a thin layer of the thermal grease

using the supplied plastic spatula.

2.1. Instructions for Socket 2066, 2011-3,

2.1. Instructions for Socket 2066, 2011-3,2.1. Instructions for Socket 2066, 2011-3,

2.1. Instructions for Socket 2066, 2011-3,

2011, AM4, TR4, sTRX4

2011, AM4, TR4, sTRX42011, AM4, TR4, sTRX4

2011, AM4, TR4, sTRX4

Place the cuplex kryos NEXT on top of the ther-

mal grease covered CPU, observing the orien-

tation as shown in the picture. Place on spring

into each recess and insert a knurled screw

through each spring into the anchor threads of

the CPU socket (only one or two revolutions).

Alternately fasten each screw a fraction of a

revolution until all four screws are fully fas-

tened.

2.2. Instructions for Socket 1150, 1151, 1155, 1156, 1200

2.2. Instructions for Socket 1150, 1151, 1155, 1156, 12002.2. Instructions for Socket 1150, 1151, 1155, 1156, 1200

2.2. Instructions for Socket 1150, 1151, 1155, 1156, 1200

Arrange back plate and black insulation mat

below the processor socket as shown in the pic-

ture. Slide one plastic washer onto the outer

thread of each retention bolt and screw the

bolts through the four mounting holes of the

motherboard into the back plate. For easy in-

stallation, the retention bolts can be screwed in

by hand or with a hexagon socket wrench.

Place the cuplex kryos NEXT on top of the ther-

mal grease covered CPU, observing the orien-

tation as shown in the picture. Slide one of the

four supplied springs onto each bolt and secure

each spring using one of the knurled head

screws (only one or two revolutions). Alternately

fasten each screw a fraction of a revolution un-

til all four screws are fully fastened.

cuplex kryos NEXT RGBpx 12/2020

3. Integration into a water cooling system and flow direction

3. Integration into a water cooling system and flow direction3. Integration into a water cooling system and flow direction

3. Integration into a water cooling system and flow direction

Integrate the cuplex kryos NEXT into a water cooling system of sufficient performance. For best

cooling performance, the coolant must be supplied through the central fitting of the cuplex kryos

NEXT. Reversed flow direction significantly decreases cooling performance.

4. RGBpx illumination

4. RGBpx illumination4. RGBpx illumination

4. RGBpx illumination

Optional: Connect the integrated RGBpx illumination module (connector to the left above the

character “N” of the engraving “NEXT”, on the side of the water block) to a compatible RGBpx

output of an Aqua Computer device. A suitable cable is included in delivery. If required, addi-

tional RGBpx components can be connected to the adjacent connector (daisy chain).

Compatible products with RGBpx output:

●D5 NEXT (41118)

●farbwerk 360 (53279)

●farbwerk nano (53280, 53281)

●OCTO (53286)

●QUADRO (53256)

An adapter for common motherboard connectors for addressable LEDs can be bought separate-

ly, product code 53285.

5. Initial operation and approved coolants

5. Initial operation and approved coolants5. Initial operation and approved coolants

5. Initial operation and approved coolants

Put the water cooling system into operation, but do not connect any other PC components to the

mains supply! Check the cuplex kryos NEXT as well as the fittings for leakages and do not put

your PC into operation unless you can definitively eliminate the possibility of coolant leaking from

the system! If any component has been in contact with coolant, do not put it into operation be-

fore it is completely dry again! For operating the PC, the cuplex kryos NEXT must be correctly

mounted and be connected to a water cooling system featuring adequate cooling performance!

For corrosion inhibition, “Double Protect Ultra” must be used as coolant!

ATTENTION:

ATTENTION:ATTENTION:

ATTENTION:

Disregarding the instructions may lead to severe damages! Aqua Computer GmbH & Co. KG

Disregarding the instructions may lead to severe damages! Aqua Computer GmbH & Co. KGDisregarding the instructions may lead to severe damages! Aqua Computer GmbH & Co. KG

Disregarding the instructions may lead to severe damages! Aqua Computer GmbH & Co. KG

cannot be held liable for damages or injuries resulting from improper installation or use of the

cannot be held liable for damages or injuries resulting from improper installation or use of thecannot be held liable for damages or injuries resulting from improper installation or use of the