Aruba Instant 100 Manual

Aruba Adgangspunkt Instant 100

Læs gratis den danske manual til Aruba Instant 100 (2 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Aruba Instant 100, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

IAP-105 Wireless Access Point

Installation Guide

About the Aruba IAP-105 Access Point

The Aruba IAP-105 wireless access point supports the IEEE 802.11n standard for

high-performance WLAN. This access point uses MIMO (Multiple-in, Multiple-

out) technology and other high-throughput mode techniques to deliver high-

performance, 802.11n 2.4 GHz and 5 GHz functionality while simultaneously

supporting existing 802.11a/b/g wireless services.

The Aruba IAP-105 access point provides the following capabilities:

Wireless transceiver

Protocol-independent networking functionality

IEEE 802.11a/b/g/n operation as a wireless access point

IEEE 802.11a/b/g/n operation as a wireless air monitor

Compatibility with IEEE 802.3af PoE

Package Contents

IAP-105 access point

Installation guide (this document)

Aruba Instant Quick Start Guide

Figure 1 IAP-105

IAP-105 Hardware Overview

Figure 2 IAP-105 Front

LEDs

The IAP-105 is equipped with four LEDs that indicate the status of the various

components of the IAP.

PWR: Indicates whether or not the IAP-105 is powered-on

ENET: Indicates the status of the IAP-105’s Ethernet port

11A/N: Indicates the status of the 802.11a/n radio

11B/G/N: Indicates the status of the 802.11b/g/n radio

For information about the IAP-105’s LED behavior, see Table 1 on page 2.

Figure 3 IAP-105 Rear

Console Port

Use the console port to connect to a terminal for direct local management.

Ethernet Port

IAP-105 is equipped with a single 10/100/1000Base-T (RJ-45) auto-sensing, MDI/

MDX wired-network connectivity port. This port supports IEEE 802.3af Power

over Ethernet (PoE) compliance, accepting 48VDC as a standard defined

Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE

midspan injector, or network infrastructure that supports PoE.

DC Power Socket

If PoE is not available, an optional Aruba IAP AC-DC adapter kit (sold

separately) can be used to power the IAP-105.

Reset Button

The reset button can be used to return the IAP to factory default settings. If you

have converted your IAP to a campus AP, pressing the reset button converts it

back to an IAP. To reset the IAP:

1. Power off the IAP.

2. Press and hold the reset button using a small, narrow object, such as a

paperclip.

3. Power-on the IAP without releasing the reset button. The power LED will

flash within 5 seconds.

4. Release the reset button.

The power LED will flash again within 15 seconds indicating that the reset is

completed. The IAP will now continue to boot with the factory default settings.

Before You Begin

IAP Pre-Installation Checklist

Before installing your IAP-105 access point, be sure that you have the following:

CAT5 UTP cable of required length

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE) source

The POE source can be any power source equipment (PSE)

Aruba IAP AC-DC adapter kit (sold separately)

Summary of the Setup Process

Successful setup of an IAP-105 access point consists of five tasks, which must be

performed in this order:

1. Identify the specific installation location for each IAP.

2. Install each IAP.

3. Verify post-installation connectivity.

4. Configure each IAP.

Identifying Specific Installation Locations

You can mount the IAP-105 access point on a wall or on the ceiling. Each

location should be as close as possible to the center of the intended coverage

area and should be free from obstructions or obvious sources of interference.

These RF absorbers/reflectors/interference sources will impact RF propagation

and should have been accounted for during the planning phase and adjusted for

in VisualRF.

Identifying Known RF Absorbers/Reflectors/Interference

Sources

Identifying known RF absorbers, reflectors, and interference sources while in

the field during the installation phase is critical. Make sure that these sources are

taken into consideration when you attach an IAP to its fixed location.

RF absorbers include:

Cement/concrete—Old concrete has high levels of water dissipation, which

dries out the concrete, allowing for potential RF propagation. New concrete

has high levels of water concentration within the concrete, blocking RF

signals.

Natural Items—Fish tanks, water fountains, ponds, and trees

Brick

RF reflectors include:

Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/

heating ducts, mesh windows, blinds, chain link fences (depending on

aperture size), refrigerators, racks, shelves, and filing cabinets

Do not place an IAP between two air conditioning/heating ducts. Make sure

that APs are placed below ducts to avoid RF disturbances.

RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Cordless headset such as those used in call centers or lunch rooms

Installing the IAP

Using the Integrated Wall-Mounting Slots

The keyhole-shaped slots on the back of the IAP can be used to attach the device

upright to an indoor wall or shelf. When you choose the mounting location, allow

additional space at the right of the unit for cables.

1. Since the ports are on the back of the device, make sure that you mount the

IAP in such a way that there is a clear path to the Ethernet port, such as a pre-

drilled hole in the mounting surface.

2. At the mounting location, install two screws on the wall or shelf, 1 7/8 inches

(4.7 cm) apart. If you are attaching the device to drywall, Aruba recommends

using appropriate wall anchors (not included).

3. Align the mounting slots on the rear of the IAP over the screws and slide the

unit into place (see Figure 4).

Figure 4 Installing the IAP-105 Access Point on a Wall

Using the Integrated Ceiling Tile Rail Slots

The snap-in tile rail slots on the rear of the IAP can be used to securely attach the

device directly to a 15/16" wide, standard ceiling tile rail.

1. Pull the necessary cables through a prepared hole in the ceiling tile near

where the IAP will be placed.

2. If necessary, connect the console cable to the console port on the back of the

IAP.

Hold the IAP next to the ceiling tile rail with the ceiling tile rail mounting slots at

approximately a 30-degree angle to the ceiling tile rail (see Figure 5). Make sure

that any cable slack is above the ceiling tile.

Figure 5 Orienting the Ceiling Tile Rail Mounting Slots

3. Pushing toward the ceiling tile, rotate the IAP clockwise until the device

clicks into place on the ceiling tile rail.

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations

and practices.

Ethernet Ports

The RJ45 Ethernet port (ENET) supports 10/100/1000Base-T auto-sensing MDI/

MDX connections. Use these ports to connect the IAP to a twisted pair Ethernet

LAN segment. Use a 4- or 8-conductor, Category 5 UTP cable up to 100 m (325

feet) long.

Inform your supplier if there are any incorrect, missing, or damaged parts. If

possible, retain the carton, including the original packing materials. Use

these materials to repack and return the unit to the supplier if needed.

AP105_005

AP105_001

105

PWR

ENET

11B/G/N

11A/N

FCC Statement: Improper termination of access points installed in the

United States (non-US Regulatory Domain model/s) will be in violation of

the FCC grant of equipment authorization. Any such willful or intentional

violation may result in a requirement by the FCC for immediate termination

of operation and may be subject to forfeiture (47 CFR 1.80).

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands.

Please refer to the Aruba Instant User Guide for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande

fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au Aruba Instant User

Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet.

Weitere Informationen bezlüglich Einschränkungen finden Sie im Aruba

Instant User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare

riferimento alla Aruba Instant User Guide per avere informazioni detagliate

sulle restrizioni.

AP105_002

CONSOLE

ENET

12V 1.25A

CONSOLE

ENET

Power

Connector

Reset Button

Aruba Networks, Inc., in compliance with governmental requirements, has

designed the IAP-105 access points so that only authorized network

administrators can change the settings. For more information about IAP

configuration, refer to the Aruba Instant Quick Start Guide and Aruba

Instant User Guide.

Access points are radio transmission devices and as such are subject to

governmental regulation. Network administrators responsible for the

configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel

assignments appropriate to the location in which the access point will be

used.

RF Radiation Exposure Statement: This equipment complies with FCC

RF radiation exposure limits. This equipment should be installed and

operated with a minimum distance of 13.78 inches (35 cm) between the

radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter

must not be co-located or operating in conjunction with any other antenna

or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this

device is restricted to indoor use to reduce the potential for harmful

interference with co-channel Mobile Satellite Systems.

Service to all Aruba Networks products should be performed by trained

service personnel only.

Make sure the IAP fits securely on the ceiling tile rail when hanging the

device from the ceiling; poor installation could cause it to fall onto people

or equipment.

AP105_003

AP105_004

Produkt Specifikationer

Mærke:	Aruba
Kategori:	Adgangspunkt
Model:	Instant 100

Har du brug for hjælp?

Hvis du har brug for hjælp til Aruba Instant 100 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Adgangspunkt Aruba Manualer

10 August 2025

19 September 2024

5 September 2024

28 August 2024

28 August 2024

Aruba Instant IAP-175 Manual

10 August 2024

Aruba AP-93H Manual

9 August 2024

Aruba AP-567 Manual

5 August 2024

Aruba Instant IAP-175P Manual

3 August 2024

Aruba Instant RAP-108 Manual

1 August 2024

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

Planet WDAP-W3600BE Manual

11 December 2025

Cambium Networks X7-53X Manual

20 November 2025

Cambium Networks X7-55X Manual

19 November 2025

Teltonika DAP140 Manual

18 November 2025

Cudy AP1300 Wall Manual

8 November 2025

EtherWAN EW75200 Manual

4 November 2025

D-Link DBR-X3000-AP Manual

1 November 2025

Draytek VigorAP 700 Manual

19 Oktober 2025

Lancom LN-860 Manual

16 Oktober 2025

Mikrotik SXT 5 ac Manual

15 Oktober 2025