Atdec SD-AT-DK-B Manual

Atdec Ikke kategoriseret SD-AT-DK-B

Læs gratis den danske manual til Atdec SD-AT-DK-B (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Atdec SD-AT-DK-B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Component Checklist

Installation Instructions

SPACEDEC ACROBAT

ARTICULATED ARM

Single Arm

Articulated Arm

Assembly (x1)

Base Casting (x1)

Cable Wrap

Applicator (x1)

Top Cap Tool (x1)

2.5mm Allen

Key (x1)

16mm Cable

Wrap (x1)

M10 Interscrew (x1)

Cable Clip (x3)

M6x12mm

Countersunk

Screw (x2)

Extension

Clip (x4)

Desk Clamp Box

Desk Clamp

Bracket (x1)

M8 Desk Clamp

Screw (x2)

Pressure

Plate (x2)

Component Checklist

Check you have received all parts against the Component Checklist above.

Bits Box

5mm Allen

Key (x1)

Assembling the Arm

Adjusting the Display

As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the mounting hole pattern does not comply with the

international VESA standards. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice.

Published: 29.03.11

Installation Complete

14 Gauge Self

Tapping Screw (x2)

B.1. Disassemble the Tube Assembly

In order to attach the Articulated Arm to the

tube assembly you will need to remove the

Top Cap and Threaded Rod as shown:

B.2. Assemble the Articulated Arm

Assemble the Articulated Arm as shown:

Top Cap and

Threaded Rod

Arm Assembly

Internal Tube Post

Spacer

Tube

Top Cap and

Threaded Rod

Internal

Tube Post

Spacer

Tube

Collar

Mounting Fasteners

M4x10mm

Screw (x4)

M4x12mm

Screw (x4)

M4x16mm

Screw (x4)

Tube Assembly (x1)

Threaded Rod

and Top Cap (x1)

Collar

Inner Tube Post

Spacer Tube

Washer (x1)

H.1. Adjusting the Ball Joint Resistance

The Acrobat Articulated Arm comes factory set to support 6kg displays. Adjust the arm to suit the weight of your

display as shown in the following steps:

Depending on the weight of the monitor, it may

be necessary to make adjustments to the Ball Joint

Mechanism. If the monitor doesn’t hold its position or

is too resistant, adjust the four tension screws located

around the Ball Joint (see diagram on the right) using

the supplied 2.5mm Allen Key.

Check the

display, and then adjust again if necessary.

NOTE: Be sure to adjust screws evenly.

Tighten

Loosen

Tension

Screws (x4)

Ball Joint

2.5mm

Allen Key

H.2. Adjusting the Pivot Head Resistance

It is possible to control the amount of resistance in the

Pivot Head to suit your display.

To increase the resistant of the Pivot Head to suit heavier

displays, use the 5mm Allen Key supplied in the Desk

Clamp Box to tighten the interscrew in a clockwise

direction.

To decrease the resistance of the Pivot Head to suit

lighter displays, loosen the interscrew in an

anti-clockwise direction.

NOTE: It is recommended the Pivot Head be left

at the factory setti

ng for best performance.

Pivot Head

Interscrew

5mm Allen Key

Loosen

Tighten

H.3. Adjusting the Articulated Arm/Gas Strut Resistance

3kg

Monitor

9kg

Monitor

Arm

Raise Gas

Strut to suit

lighter display

5mm

Allen key

Gas Strut

Lighter

Heavier

Lower Gas Strut to

suit heavier display

4mm Allen

Key (x1)

Ergonomic Guidelines

H.3.1. Depending on the weight of the monitor, it

may be necessary to adjust the arm. This can be

done by using the 5mm Allen Key supplied in the

Desk Clamp Box.

H.3.2. If the arm tends to automatically rise or fall

when the display is attached, it will be necessary

to make small adjustments to the gas strut. (see

diagram on the right)

H.3.3. If the arm tends to rise, the gas strut

position should be raised. If the arm tends to fall,

the gas strut position shou

ld be lowered.

Ergonomists recommend that the optimal position of your screen should be slightly below eye level.

When looking at the screen’s centre the user should have a downward visual angle of approximately

10°-20°. As a guide, the height (h) of your display should approximately be as follows:

Tall Male (Max): 560mm (22”) Tall Female (Max): 520mm (20

2”)

Short Male (Min): 368mm (14

2”) Short Female (Min): 356mm (14”)

For visual comfort, a viewing distance (d) between 500mm (19

2”) to 750mm (29

2”) is

recommended.

Angular adjustments to reduce reflection on your monitor should range between 5° forward tilt to 15°

backward tilt.

Desk Clamp

15°

5°

HORIZONTAL SIGHT LINE (d)

CENTRE OF SCREEN

10°-20°

Recommended Viewing Distance / Height

Recommended Mounting Position

50mm (2”)

When mounting the Spacedec Acrobat Articulated Arm, ensure the correct focal distance can be

achieved for ultimate visual comfort (Refer to Recommended Viewing Distance / Height below)

Desk Clamp Bolt Through

(h)

15mm Hole (

”)

Base Casting

Produkt Specifikationer

Mærke:	Atdec
Kategori:	Ikke kategoriseret
Model:	SD-AT-DK-B
Produktfarve:	Sort
Monteringstype:	Skrivebord
Hældningsvinkelområde:	-40 - 40 °
Panoreringsområde:	-40 - 40 °
Rotationsvinkel:	360 °
Maksimal vægtkapacitet:	9 kg
Maksimal skærmstørrelse kompatibilitet:	24 "
Antal understøttede skærme:	1
Minimal skærmstørrelse kompatibilitet:	12 "
Montering interface kompatibilitet (min.):	75 x 75 mm
Montering interface kompatibilitet (maks.):	100 x 100 mm