Atdec TH-1040-CTS Manual

Atdec Ikke kategoriseret TH-1040-CTS

Læs gratis den danske manual til Atdec TH-1040-CTS (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Atdec TH-1040-CTS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Component Checklist

Mounting Plate

Pole Assembly

VESA Plate

Mounting Plate Cover

Coach Screw (x4)

Nylon Anchor (x4)

M4/5/10 Washer

(x4 each)

Set Screw

M5/6 Spacer (x4)

M4/5 Spacer (x4)

(optional) Security Screw

2.5/3/5mm

Allen Key

M4x16/25mm (x4 each)

M5x16/25mm (x4 each)

M6x16/30mm (x4 each)

Pole Assembly

Mounting Plate Cover

PUSH

Screw Pole Assembly

into Mounting Plate by

twisting top half of the

Pole Assembly only.

Pole

Assembly

Mounting Plate

TWIST

3mm

Allen Key

Set Screw

Insert Set Screw into the

Mounting Plate to lock the

Pole Assembly in position.

Pole Assembly

Mounting Plate

Cover

PUSH

Installation Instructions

TH-1040-CTS

TH-1040-CTL

Ceiling Tilt Short Mount / Ceiling Tilt Long Mount

IMPORTANT INFORMATION:

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

Step 2. Install Mounting Plate

Step 4.

Attach Pole Assembly to Mounting Plate

! IMPORTANT - Install Telehook 1040 Ceiling Tilt Mount (Short/Long) as per Installation Instructions.

! This product supports a maximum load of 25kg (55lbs).

! This product supports VESA mounting hole configurations 75x75mm, 100x100mm, 200x100mm, 200x200mm.

! The manufacturer accepts no responsibility for incorrect installation.

Step 5. Position Mounting Plate Cover

Step 3. Install Mounting Plate Cover

Display Mounting

Screws

Hardware

Tools Required:

Power drill

•

7mm

(¼”)

drill bit

•

12mm

(½”)

masonry drill bit

•

Phillips head screw driver•

17mm (11/ ”) 16 Socket Wrench or Shifter

•

Masonry Ceiling

Timber Ceiling

Using the Mounting

Plate

as a template, mark

out

and drill

4x Ø7mm

(¼”)

holes,

Ø12mm

(½”)

for masonry

ceilings,

70mm (2.75”) deep.

Nylon Anchor

Mounting Plate

Coach Screw

M10 Washer

False Ceiling Cover

TH-1040-CTSW

TH-1040-CTLW

Set Screw

Cable

Access Port

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 29.09.11 ©

Step 6. Set Height of Pole

Step 9. Cable Management

Whilst supporting the lower half of Pole

Assembly loosen

the

Socket Cap Screws (x2).

Slide Pole Assembly

to the desired height.

Tighten the Socket Cap

Screws (x2) to set the height.

Step 8. Attach Display to Pole Assembly

Feed cables down the Pole

Assembly through the Cable

Access Port.

Pull cables out from lower

half of the Pole Assembly

and

connect to Display.

Step 10. Height Adjustment

Pole Joint

LOOSEN

TIGHTEN

FIRMLY

Socket Cap

Screw

5mm Allen Key

ADJUST

HEIGHT

Loosen Socket Cap

Screws (x2) on the Donut.

TILT

PAN

Step 7. Attach VESA Plate to Display

TOP

Step 11. Final Adjustment

A. Pan,

Tilt and Rotate

the Display as

required.

If necessary, centralise the

Pole Joint by tightening the

Set Screws (x2) to suit.

2.5mm

Allen Key

VESA plate

Mounting

Screws

B. Slide

the height of the

Donut

as required. Tighten

Socket Cap Screws to lock.

Step 12. Install False Ceiling Cover

PORTRAIT TO

LANDSCAPE

Choose the appropriate

mounting hardware to suit the Display.

Spacers

(optional, for recessed

mounting holes)

B. PUSH

HOOK

(optional) Once Display

is attached, insert

Security Screw using

Phillips-head screwdriver

Security

Screw

Socket Cap

Screw

5mm

Allen Key

VESA Ball Mount

Tension Plate at rear

3mm Allen Key

If necessary tighten the VESA

Ball

Mount by adjusting the

Tension Plate. Using the 3mm

Allen Key adjust screws evenly.

Donut

SLIDE

False Ceiling

Cover

CLICK

Lower Pole

If the Lower Pole hangs below a suspended ceiling, clip the False

Ceiling Cover over the Lower Pole, and push up to the ceiling.

PUSH

Produkt Specifikationer

Mærke:	Atdec
Kategori:	Ikke kategoriseret
Model:	TH-1040-CTS

Har du brug for hjælp?

Hvis du har brug for hjælp til Atdec TH-1040-CTS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Atdec Manualer

Atdec Telehook TH-1040-CTS Manual

20 Juli 2025

Atdec TH2050-VFM-TAA Manual

20 Juli 2025

Atdec ProAV TH-VWV Manual

20 Juli 2025

Atdec Telehook TH-3070-CTS Manual

20 Juli 2025

Atdec Telehook TH-3070-CTL Manual

20 Juli 2025

Atdec AW-FB Manual

30 Januar 2025

Atdec AWM-AHX-S Manual

28 December 2024

Atdec AWM-HN Manual

7 December 2024

Atdec AD-TVAC-CM-B Manual

7 December 2024

Atdec AD-TVAC-CM-W Manual

7 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Black Diamond HotForge Hybrid Quickpack Manual

31 Juli 2025

RADEMACHER RolloTron Comfort DuoFern 1800 Manual

31 Juli 2025

Infiniton GG-430 Manual

31 Juli 2025

AIC RSC-4ET Manual

31 Juli 2025

Advantech PPC-MB-610 Manual

31 Juli 2025

Intellinet 561730 Manual

31 Juli 2025

Oppo X7 Ultra Manual

31 Juli 2025

Oppo K11 Manual

31 Juli 2025

Bestway Hydro-Force 6531R Manual

31 Juli 2025

RYOBI RSCR4 Manual

31 Juli 2025