Atdec TH-PT8 Manual

Atdec Ikke kategoriseret TH-PT8

Læs gratis den danske manual til Atdec TH-PT8 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Atdec TH-PT8, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Instructions

TH-PT8

Projector | Suspended Ceiling Tile 8"

Component Checklist

IMPORTANT INFORMATION:

! IMPORTANT - Install Telehook Projector - Suspended Ceiling Tile 8" as per Installation Instructions.

! Compatible with 1.5” NPT Pole Mounts, Atdec Pole Mount (TH-WH-PJ-CM), Atdec Flush Mount (TH-WH-PJ-FM),

Atdec ProAv Projector Ceiling Mount (TH-PF) and Atdec pole accessories (TH-PPA-18-25, TH-PPA-24-48 & TH-PPE-24).

! Maximum weight capacity 22.7kg (50lbs).

! The manufacturer accepts no responsibility for incorrect installation.

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

Step 2. Remove Existing Ceiling Tile

Remove existing ceiling tile from ceiling grid where the product

is going to be installed.

NOTE: Keep this ceiling tile for later in the installation.

TIP: Also temporarily remove an adjacent ceiling tile to allow easy

access to the product during installation.

Step 3. Fix Anchors to True Ceiling

Uncoil Support Wire and cut into 4 equal lengths. Select the anchoring method appropriate to your ceiling (see below).

NOTE: Each anchor point should be directly above each corner of the Suspended Ceiling Tile.

Wooden Joists

Drill 4x Ø6mm holes, at least 50mm deep

(4x Ø¼

”

holes, 2”deep).

Fully screw Lag Eye bolts into wooden joists.

Solid Concrete

Drill 4x Ø6mm holes, 36mm deep

(4x Ø¼

”

holes 1½

”

deep).

Tap anchors into hole to an embedded depth

of at least 25mm deep (1” deep).

Using a claw hammer, pull anchor out 6mm

(¼

”

) to activate anchor.

Truss Beams

Thread one end of Support Wires through the

trusses, and wrap 5 times to secure.

Hardware

M6 Wing

Nut (x4)

M6 Washer

(x8)

Lag Eye

Bolt (x4)

Concrete

Anchor

Bolt (x4)

Safety Clamp

(x2)

Thread one end of each support wires through

a Lag

Eye Bolt, and wrap 5 times to secure.

Thread one end of each support wires through

a Lag

Eye Bolt, and wrap 5 times to secure.

Support Wire (x4)

Lag Eye Bolt (x4)

Concrete Anchor

Bolt (x4)

Support Wire (x4)

Truss Beam

Support

Wire (x4)

Solid

Concrete

Wooden

Joist

M6 Set

Screw (x2)

Turnbuckle

(x4)

Support Wire

Safety Wire

M6x16mm

Screw (x4)

M5x16mm

Screw (x4)

Upper

Mounting Plate

Lower

Mounting Plate

Mounting

Collar

3mm

Allen Key

Turnbuckle

Hooks

Tools Required:

Phillips head screwdriver

Wire cutters

Power drill

6mm (

”) drill bit

6mm (

”) masonry drill bit

Claw hammer

Jigsaw/Hole cutter

Spirit level

Suspended

Ceiling Tile

Ceiling Covers

(x3)

Step 4. Attach Turnbuckles onto Support Wires

Loop each dangling Support Wire through a Turnbuckle, and wrap

5 times to secure.

Make sure that the position of the p1-x4 Turnbuckles are approximately

at the same height.

TIP: When mounting 1.5” NPT pole mounts or flush mounts the

turnbuckle hooks should be level with the top of ceiling grid.

When mounting an Atdec pole mount (TH-WH-PJ-CM) the hooks

should be approximately 130mm (5”) above the top of the ceiling grid.

Turnbuckle

(x4)

Support

Wire (x4)

Produkt Specifikationer

Mærke:	Atdec
Kategori:	Ikke kategoriseret
Model:	TH-PT8
Produktfarve:	Hvid
Monteringstype:	Væg/loft
Maksimal vægtkapacitet:	22.7 kg
Loftsmontering rørlængde (maks.):	60 cm
Loftsmontering rørlængde (min.):	20 cm