Audio-Technica AT846/C Manual

Audio-Technica Mikrofon AT846/C

Læs gratis den danske manual til Audio-Technica AT846/C (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Audio-Technica AT846/C, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
CARDIOID CONDENSER BOUNDARY MICROPHONE
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
0°
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Optional Accessories:
AT8506 four-channel 48V phantom
power supply (AC powered).
AT8801/EU single-channel 48V
phantom power supply (AC pow-
ered).
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
FORM No. ATGC-L0182-11-E
Machida • Tokyo • Japan
SPECIFICATIONS
ELEMENT Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN Unidirectional (Cardioid in hemisphere
above mounting surface)
FREQUENCY RESPONSE 60-20,000 Hz
OPEN CIRCUIT SENSITIVITY -37 dB (14.1 mV) re 1V at 1 Pa
IMPEDANCE 100 ohms
MAXIMUM INPUT SOUND LEVEL 134 dB SPL, 1 kHz at 1% T.H.D.
SIGNAL-TO-NOISE RATIO >66 dB, 1 kHz at 1Pa
PHANTOM POWER REQUIREMENTS 11-52V DC, 2 mA typical
WEIGHT 48 g
DIMENSIONS 30.0 mm - diameter,
64.6 mm - length
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED One pair isolators
Th e AT 8 4 6/C is a wid e - r ange
c o n d e n s e r m i c r o p h o n e w i t h
a unidi rectio nal po lar pattern .
It is d e s ign e d fo r unob trusiv e
table, ceiling or panel-mounted
applications for high-quality sound
reinforcement, teleconferencing,
professional recording, television
a n d o t h e r d e m a n d i n g s o u n d
pickup applications.
T h e A T 8 4 6 / C i s e q u i p p e d
w i t h U niGu a r d ® R FI - sh i e l d i n g
t e c h n o l o g y , w h i c h o f f e r s
out s tan d i ng r e j ecti o n of r a dio
frequency interference (RFI). The
microphone is RoHS compliant –
free from all substances specified
in the EU directive on hazardous
substances.
The microphone should be placed on a at, unobstructed mounting
surface. The small diameter capsule near the boundary eliminates
phase distortion and delivers clear, high-output performance.
The microphone requires 11V to 52V phantom power for operation.
The microphone is enclosed in a heavy-duty die-cast case and
protected by a two-layer steel mesh grille. The low-profile housing
has a low-reflectance black finish. Isolators are included with the
microphone for optional mechanical isolation from the mounting
surface.
Output is low impedance balanced. The balanced signal appears
across Pins 2 and 3, while the ground (shield) connection is Pin 1.
Output is phased so that positive acoustic pressure produces positive
voltage at Pin 2 in accordance with industry convention.
To mount the AT846/C in a ceiling or table top without the isolators,
a 20.5 mm diameter hole is required. To mount the AT846/C with the
isolators, a 23.5 mm hole is required. Place the isolators on either
side of the hole to achieve mechanical isolation from the mounting
surface. The small cardioid circle on the AT846/C bezel indicates the
"front" of the microphone.
The microphone shall be a xed-charge condenser designed for use
in table, ceiling or panel-mount boundary applications. It shall have
a frequency response of 60 Hz to 20,000 Hz and an unidirectional
(cardioid in a hemisphereabove the mounting surface boundary)
polar pattern. It shall incorporate a self-contained power module
and require 11V to 52V DC phantom power to operate. It shall offer
outstanding rejection of radio frequency interference (RFI). It shall be
capable of handling sound input levels up to 134 dB. Nominal open
circuit output voltage shall be 14.1 mV at 1 kHz, 1 Pascal. Output
shall be low impedance balanced (100 ohms) from an integral 3-pin
XLRM-type connector.
The microphone shall have a maximum diameter of 30.0 mm and an
overall length of 64.6 mm. Weight shall be 48 grams. The microphone
shall be housed in an all-metal case with a two-layer steel mesh
grille. Finish shall be low reflectance black. A small cardioid circle
on the bezel shall indicate the "front" of the microphone. Resilient
isolators shall be provided for reduction of mechanical noise transfer
from the mounting panel.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 43 C for extended periods. Extremely high °
humidity should also be avoided.

Produkt Specifikationer

Mærke: Audio-Technica
Kategori: Mikrofon
Model: AT846/C

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica AT846/C stil et spørgsmål nedenfor, og andre brugere vil svare dig


Mikrofon Audio-Technica Manualer

Audio-Technica

Audio-Technica ATW-CHG3AAD Manual

15 Oktober 2025
Audio-Technica

Audio-Technica ATW-2129CI Manual

29 August 2025
Audio-Technica

Audio-Technica ATM350UcH Manual

2 August 2025
Audio-Technica

Audio-Technica BP899LcH Manual

2 August 2025
Audio-Technica

Audio-Technica ATM350GL Manual

2 August 2025
Audio-Technica

Audio-Technica System 10 Stompbox ATW-1501 Manual

2 August 2025
Audio-Technica

Audio-Technica BP892c Manual

2 August 2025
Audio-Technica

Audio-Technica AT882TL Manual

2 August 2025
Audio-Technica

Audio-Technica ATM350SL Manual

2 August 2025
Audio-Technica

Audio-Technica System 20 PRO Manual

17 Juli 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

Nady

Nady SCM 800 Manual

4 November 2025
Nady

Nady SP-R3 Manual

4 November 2025
Phenyx Pro

Phenyx Pro PTU-7000A Manual

4 November 2025
JARO

JARO J100-CS Manual

4 November 2025
MayBesta

MayBesta WM150 Manual

3 November 2025
XIAOKOA

XIAOKOA N80-B Manual

3 November 2025
Singing Machine

Singing Machine CPK565 Manual

3 November 2025
Shaevle

Shaevle SW-16 Manual

3 November 2025
HOTEC

HOTEC H-U25 Manual

3 November 2025
Saramonic

Saramonic Blink500 B3 Manual

3 November 2025