Audio-Technica ATND8677a Manual

Audio-Technica Mikrofon ATND8677a

Læs gratis den danske manual til Audio-Technica ATND8677a (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om Audio-Technica ATND8677a, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ATND8677

Microphone Desk Stand with Dante™ Network Output

Features

Description

The ATND8677 is a Dante-enabled microphone desk stand for use with any gooseneck microphone with a

three-pin XLRM-type output connector. The desk stand is designed for surface-mount applications such as high-

quality sound reinforcement, conferencing, distance learning and other demanding sound pickup applications.

The desk stand features a touch-sensitive capacitive-type user switch with integral red/green LED status

indicator. In Local mode the user switch mutes and unmutes the microphone. It can be set to toggle between

live and muted audio (toggle on/off), to permit live audio only while the switch is pressed (press to talk), or to

mute the audio while the switch is pressed (press to mute). In Remote mode the user switch can be used to

trigger functions on compatible Dante-enabled devices, such as a video camera's pan/tilt or a room’s lighting

preset. While in Remote mode the desk stand's audio output is controlled remotely.

The audio output of the ATND8677 can be routed using Audinate's Dante Controller, which is available for

download at the Audinate website (www.audinate.com). The site also provides Dante routing and software

instructions.

The desk stand's heavy die-cast case and non-slip silicone foam bottom pads minimize coupling of surface

vibration to the microphone. The stand features a low-reectance black nish.

Operation and Maintenance

The ATND8677 is powered by network PoE. The electronics in the desk stand take up to 30 seconds to stabilize

after power is applied.

The desk stand features a touch-sensitive user switch with integral red/green LED status indicator. The user

switch has four Local settings that can be chosen by pressing the button beneath “SWITCH FUNCTION” and

“DEFAULT MODE.” The default setting is TOGGLE ON/OFF. Press the button once to change setting to TOGGLE

ON/OFF. In both settings the user switch will toggle between mute and unmute – the only difference is the

status of the audio when the desk stand is turned on. Press the button a second time to select MOM. ON

(momentary on), wherein the audio will be on only while the user switch is being pressed (press to talk). Press

the button a third time to select MOM. OFF (momentary off), wherein the audio will be muted while the user

switch is being pressed. Press the button a fourth time to cycle the setting back to the default. The “SWITCH

FUNCTION” and “DEFAULT MODE” LEDs will illuminate red or green to indicate the current setting.

Turn the low-cut UniSteep® lter on and off by pressing the button beneath “LOW CUT” on the bottom of the

desk stand. The lter is off by default. The LED above “LOW CUT” illuminates red when the lter is off, green

when it is on.

There are three input gain levels that can be selected: +30 dB (for loudest voices), +40 dB and +50 dB (for

softest voices). To adjust the gain level, press the button beneath “GAIN” on the bottom of the desk stand.

Pressing the button once changes the level from +30 dB to +40 dB, pressing it again changes the level to +50

dB and pressing a third time returns the level to +30 dB. The LED above “GAIN” illuminates green for +30 dB,

orange for +40 dB and red for +50 dB.

By default, the desk stand supplies 12V DC of phantom power, which is required by most gooseneck

microphones. Phantom power can be turned off by pressing the button beneath “PHANTOM” on the bottom of

the desk stand. The LED above “PHANTOM” illuminates green when power is on and red when it is off.

To lock the Local settings, press and hold the button beneath “LOCK” on the bottom of the desk stand. Press

and hold again to unlock settings. The LED above “LOCK” will illuminate red when locked and remain unlit

when not locked. If a setting button is pressed while the lock is on, the LOCK LED will blink.

All LEDs on the bottom of the desk stand will turn off seven seconds after the last button is pressed. Pressing

any button will cause the LEDs to relight.

To return the desk stand to its default Local settings, press the GAIN and LOW CUT buttons simultaneously.

The desk stand can also be controlled remotely via third-party software.* When this software is used it will

Specifications

Frequency response 20-20,000 Hz

Low frequency roll-off 80 Hz, 18 dB/octave

Input impedance 1.4 kΩ

Maximum input levels -10 dBu @ +30 dB gain

-20 dBu @ +40 dB gain

-30 dBu @ +50 dB gain

Signal-to-noise radio 68 dB, 1 kHz at 1 Pa

Power requirements PoE IEEE802.3af standard

Power consumption 1.5W

Microphone phantom power 12V DC

Switches Local Mode:

Touch-sensitive capacitive type user switch function:

toggle (mute on power up), toggle (talk on power up),

momentary on, momentary off;

Low-cut lter: at, roll-off; Gain: +30 dB, +40 dB, +50 dB

Phantom power: +12V DC, off

Remote Mode:

Low-cut and Gain via third-party software*

Weight 770 g

Dimensions 133.0 mm (L), 93.8 mm (W), 46.2 mm (H)

Input connector 3-pin XLRF-type

Output connector Physical level: standard Ethernet

Dante network Connector: single RJ45

Cable quality: Shielded CAT5 or CAT6 recommended

Transmission speed: 100 Mbps

FORM No. ATGC-L0328-15-E

Machida • Tokyo • Japan

override local control, causing the audio to remain on and the red/green LED status indicator, low-cut lter and

input gain level to be controlled remotely. In Remote mode the desk stand’s user switch can be programmed to

trigger functions on compatible Dante-enabled devices. When in remote mode the Remote LED is illuminated.

Avoid leaving the desk stand in the open sun or in areas where temperatures exceed 43° C for extended

periods. Extremely high humidity should also be avoided.

Note: Placing any object on a surface (such as a conference table) before its nish is fully cured may result in

damage to the nish.

*For a list of compatible third-party software consult the ATND8677 product prole at Audio-Technica.com.

User Switch Settings and Functions in Local Mode

CONTROL

User Switch Mode SWITCH FUNCTION

LED Color

DEFAULT MODE

LED Color

Default Toggle

(mute on power up)

Green Red

1st Press Toggle

(talk on power up)

Green Green

2nd Press Press to Talk Red Red

3rd Press Press to Mute Red Green

network microphones

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	ATND8677a

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ATND8677a stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATW-CHG3AAD Manual

15 Oktober 2025

Audio-Technica ATW-2129CI Manual

29 August 2025

Audio-Technica ATM350UcH Manual

2 August 2025

Audio-Technica BP899LcH Manual

2 August 2025

Audio-Technica ATM350GL Manual

2 August 2025

Audio-Technica System 10 Stompbox ATW-1501 Manual

2 August 2025

Audio-Technica BP892c Manual

2 August 2025

Audio-Technica AT882TL Manual

2 August 2025

Audio-Technica ATM350SL Manual

2 August 2025

Audio-Technica System 20 PRO Manual

17 Juli 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

Nady SCM 800 Manual

4 November 2025

Nady SP-R3 Manual

4 November 2025

Phenyx Pro PTU-7000A Manual

4 November 2025

JARO J100-CS Manual

4 November 2025

MayBesta WM150 Manual

3 November 2025

XIAOKOA N80-B Manual

3 November 2025

Singing Machine CPK565 Manual

3 November 2025

Shaevle SW-16 Manual

3 November 2025

HOTEC H-U25 Manual

3 November 2025

Saramonic Blink500 B3 Manual

3 November 2025