Audio-Technica ES933/H Manual

Audio-Technica Mikrofon ES933/H

Læs gratis den danske manual til Audio-Technica ES933/H (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Audio-Technica ES933/H, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

HYPERCARDIOID CONDENSER

HANGING MICROPHONE

- Designed for quality sound

reinforcement, professional

recording, television and other

demanding sound pickup

applications.

- Superior off-axis rejection for

maximum gain before feedback.

- Furnishing with a vinyl-coated steel

hanger that allows to be adjusted for

correct positioning.

- Accepts interchangeable elements

to permit angle of acceptance from

90° to 120°.

- Snap-on foam windscreen effectively

reduces noise from wind or

ventilation air currents.

- Connected power module can be

powered from any external 11V to

52V phantom power supply with an

XLRM-type connector.

- Enclosed in a rugged housing with

a low-reectance black nish. And

also available with white housing,

cable and hanger as the ES993W/H.

The ES933/H shall have a permanently-attached 15.2m miniature low-

noise cable, and require 11V to 52V DC phantom power for operation.

A uniform 100° angle of acceptance provides well-balanced audio

pickup. The microphone should be located forward of the front-most

source, above the rear-most source, and "aimed" between them (Fig.1).

Increasing the height of the mic above the sources will tend to equalize

sound levels between them, but may also increase from the mic to the

rear-most pickup should be no more than twice the distance to the front

source, to maintain front-to-rear balance (Fig.1).

Width of pickup is approximately 2.5 times the distance to the closest

performer. If additional mics are needed for wide sources, they should

be positioned apart laterally at least 2.5 times the distance to front

source, to avoid phase cancellation (Fig.2).

Output is low impedance balanced. The output connector mates with

XLRF-type cable connectors. The balanced signal appears across Pins

2 and 3, while the ground (shield) connection is Pin 1. Output is phased

so that positive acoustic pressure produces positive voltage at Pin 2, in

accordance with industry convention.

At integral 80 Hz high-pass filter provides easy switching from a flat

frequency response to a low-end roll-off. The roll-off position reduces

the pickup of low-frequency ambient noise (such as trafc, air-handling

systems, etc.), room reverberation and mechanically coupled vibrations.

Avoid leaving the microphone in the open sun or in areas where

temperatures exceed 43°C for extended periods. Extremely high

humidity should also be avoided.

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

Optional Accessories:

AT8506 four-channel 48V phantom power

supply (AC powered).

AT8801/EU single-channel 48V phantom

power supply (AC powered).

Polar Pattern

Frequency Response

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

Frequency in Hertz

LEGEND 12” or more on axis

Roll-off

Response in dB

FORM No. ATGC-L0056-06-E

Machida • Tokyo • Japan

SPECIFICATIONS

ELEMENT Fixed-charge back plate

permanently polarized condenser

POLAR PATTERN Hypercardioid

FREQUENCY RESPONSE 80-20,000 Hz

LOW-FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave

OPEN CIRCUIT SENSITIVITY -40 dB (10.0 mV) re 1V at 1 Pa

IMPEDANCE 250 Ω (1000 Ω without power module)

MAXIMUM INPUT SOUND LEVEL 138 dB SPL, 1 kHz at 1% T.H.D.

DYNAMIC RANGE (typical) 109 dB, 1 kHz at Max SPL

SIGNAL-TO-NOISE RATIO 65 dB, 1 kHz at 1Pa

SWITCHES Flat response, low-roll-off

PHANTOM POWER REQUIREMENTS 11-52V DC, 4 mA typical

WEIGHT Microphone

Power Module

5 g

56 g

DIMENSIONS Microphone

Power Module

23.3 mm - long,

8.4 mm - head diameter

98.0 mm - long,

18.9 mm - diameter

OUTPUT CONNECTOR Integral 3-pin XLRM-type

CABLE 15.2m - long, 3.2 mm - diameter

ACCESSORIES FURNISHED AT8109 snap-on foam windscreen

AT8452 steel hanger

OPTIONAL INTERCHANGEABLE

ELEMENTS

ESE-C cardioid (120°)

ESE-ML MicroLine ® (90°)

2.5 TIMES

DISTANCE "X"

MIC A MIC B

100° 100°

100°

ANGLE OF

ACCEPTANCE

DISTANCE "X"

LESS THAN 2 TIMES "X"

Fig.2Fig.1

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	ES933/H

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ES933/H stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATW-CHG3AAD Manual

15 Oktober 2025

Audio-Technica ATW-2129CI Manual

29 August 2025

Audio-Technica ATM350UcH Manual

2 August 2025

Audio-Technica BP899LcH Manual

2 August 2025

Audio-Technica ATM350GL Manual

2 August 2025

Audio-Technica System 10 Stompbox ATW-1501 Manual

2 August 2025

Audio-Technica BP892c Manual

2 August 2025

Audio-Technica AT882TL Manual

2 August 2025

Audio-Technica ATM350SL Manual

2 August 2025

Audio-Technica System 20 PRO Manual

17 Juli 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

Nady SCM 800 Manual

4 November 2025

Nady SP-R3 Manual

4 November 2025

Phenyx Pro PTU-7000A Manual

4 November 2025

JARO J100-CS Manual

4 November 2025

MayBesta WM150 Manual

3 November 2025

XIAOKOA N80-B Manual

3 November 2025

Singing Machine CPK565 Manual

3 November 2025

Shaevle SW-16 Manual

3 November 2025

HOTEC H-U25 Manual

3 November 2025

Saramonic Blink500 B3 Manual

3 November 2025