Audiovox Prestige Platinum APS 686T Manual

Audiovox Sikkerhed Prestige Platinum APS 686T

Læs gratis den danske manual til Audiovox Prestige Platinum APS 686T (20 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Audiovox Prestige Platinum APS 686T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/20

128-7201

1 of 20

Model APS 686T

Installation Manual

4 Channel Remote Start / Keyless Entry System

Installation Instructions

This Unit Is Intended For Installation In Vehicles With

12 Volt Negative Ground Electrical Systems,

Gasoline or Diesel With True Tach Reference

And Automatic Transmissions Only.

Kit Contents

Control Module

(2) - 4 Button Code Hopping Transmitters

4 Channel Code Learning Receiver

External Superheterodyne Antenna/Receiver

(1) - Multi Pin Input/Output Harness

(1) - Six Pin Power Harness

(1) - Four Pin Auxiliary Harness

(1) - Two Pin I/O Harness

(1) - Accessory 2 Pin Connector

(1) - 2 Pin Door Lock Harness

(2) - 30 Amp In-line Fuse Holders With Fuses

(1) - Control Switch

(1) - Programming Switch

(1) - Ring Terminal

(4) - 1/2" Long Screws

(1) - Pin Switch

(1) - Remote Start Warning Label

(1) - Literature Package

Released: 6-28-04

128-7201

2 of 20

This Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The

unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat

which may be required for certain diesel vehicles, (see selectable feature #11). If the diesel engine has a instant fire,

(no glow plug pre-heat system), feature #11 should remain in the default Gasoline mode setting. For diesel

applications, consult your dealer for the type of ignition system used in your particular vehicle. Regardless of the vehicle,

Gasoline or Diesel, for every installation, the vehicle MUST HAVE a Tach Signal Input, and an Automatic

Transmission.

INSTALLATION OF THE MAJOR COMPONENTS:

CONTROL MODULE:

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location

selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness.

Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the module

to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or block the

steering wheel preventing proper control of the vehicle. Secure the module in the chosen location using cable ties or

screws as necessary.

Do Not Mount The Module In The Engine Compartment, as it is not waterproof.

HOOD PIN SWITCH:

The pin switch included in this package is required for the safety shut down of the remote start unit. If the vehicle is

being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This

switch MUST be installed in all applications Failure to do so may result in personal injury or property damage. Mount

the switch in an area under the hood that is away from water drain paths. If necessary, the included brackets may be

used to move the switch away from rain gutters or allow mounting to the firewall behind the hood seal. In either case

the switch must be set up to allow the hood door to depress the switch at least 1/4 inch when the hood is closed and

fully extended when the hood is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check behind

the chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the

desired location and thread the pin switch into it using a 7/16" nut driver or deep well socket. If using the mounting

bracket, first secure the bracket to the desired location and secure the pin switch in the pre-threaded mounting bracket

hole.

THE RECEIVER/ANTENNA ASSEMBLY:

The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board

for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.

Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window

glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window location for

best reception. Secure the antenna with double stick tape provided. After securing the antenna, we advise also

securing a section of the antenna cable to a fixed support. This will prevent the antenna from dropping down in case

the double stick tape is exposed to extreme heat which may loosen it's gummed surface.

PROGRAM PUSH BUTTON SWITCH :

Select a mounting location that is within reach of the ignition switch, as this switch, in combination with the ignition

switch, will be used to program the selectable features of the system. It is suggested that the switch be mounted to the

lower dash panel in the driver's area. Inspect behind the chosen location to insure that adequate clearance is allowed

for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 9/32"

hole in the desired location and mount the switch by passing it through the panel from the underside. Secure the

switch using the nut and star washer. Route the switch wires toward the control module.

NOTE: During the program sequence, there are times when this switch and the ignition switch will be used simulta-

neously. We recommend that the pushbutton switch be mounted on the left side of the ignition switch to

facilitate this operation.

CONTROL SWITCH:

Select a mounting location known and accessible to the operator of the vehicle. A lower dash panel, kick panel, or

glove box is desirable. Inspect behind the chosen location to insure that adequate clearance is allowed for the body

of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines.

Produkt Specifikationer

Mærke:	Audiovox
Kategori:	Sikkerhed
Model:	Prestige Platinum APS 686T

Har du brug for hjælp?

Hvis du har brug for hjælp til Audiovox Prestige Platinum APS 686T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Sikkerhed Audiovox Manualer

Audiovox AS9233ST Manual

22 August 2024

Audiovox Prestige Platinum APS 686T Manual

21 August 2024

Audiovox APS-45 Manual

21 August 2024

Audiovox PRO-9056TW Pursuit Series Manual

21 August 2024

Audiovox APS 675 Prestige Platinum Manual

21 August 2024

Sikkerhed Manualer

Nyeste Sikkerhed Manualer

Aritech SHATTERPRO 3 Manual

15 Januar 2025

Axis Camera Station S9001 Mk II Desktop Terminal Manual

15 Januar 2025

Eminent EM6511 Manual

15 Januar 2025

Ranex RX2567-Z Manual

11 Januar 2025

NetworX NX-595E IP Communication Module Manual

5 Oktober 2024

Provision-ISR NVR2-4100P Manual

23 September 2024

Gira 0342 Manual

23 September 2024

Unitron Smart Alert Systeem Manual

23 September 2024

Netatmo Welcome Manual

21 September 2024

NetworX NX-408 Manual

20 September 2024