Audiovox PRO-9056TW Pursuit Series Manual

Audiovox Sikkerhed PRO-9056TW Pursuit Series

Læs gratis den danske manual til Audiovox PRO-9056TW Pursuit Series (2 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Audiovox PRO-9056TW Pursuit Series, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
128-8856
1 of 2
Single Channel Remote
Car Starter
Model PRO-9056TW
Owner’s Manual
FEATURES :
1 Programmable RF Transmitters, 1 Programmable RF Transceiver
Single Channel Receiver (capable of accepting 4 transmitters)
External Superheterodyne Receiver Antenna w/PushButton Switch &
Orange LED
On-Board Start Relay
On-Board Accessory Relay
On-Board Ignition 1 Relay
On-Board Ignition 2 Relay
Ignition 2 Relay Selectable On or Off During Cranking
On-Board Parking Light Relay
Ignition 3 / Shock By-Pass / GM VAT Output (relay required)
Tach Signal Learning Circuit
Two ( + ) and Two ( - ) Safety Shutdown Circuits
Alarm By-Pass Output
Accessory Outputs
(Pulse Before & After Start, During Crank & After Shut Down)
Selectable Steady or Flashing Parking Lights for Run Indication
Selectable 5, 10, 15, 20 Minute Run Time
Optional Door Unlock Feature For Vehicles Equipped With Power Doors
(Only operational while running under control of the remote start unit.)
128-8856
2 of 2
2
© 2010 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-8856
REMOTE STARTING THE VEHICLE
This will not start the vehicle if any one of the following situations exists:
The vehicle's hood lid is opened.
The gear shift selector is not in Park.
The brake pedal is depressed.
The safety control switch is in the Off position.
1) To start the vehicle, press and release the transmitter button two times within
2 seconds. The vehicle will start and remain running for the
pre-programmed time up to a 60 minute run cycle. As a
visual indication, the parking lights will flash or remain on
depending on the setting by your installation center. Addi-
tionally if the two way transceiver shown on the right is used,
the transceiver will play a melody when the vehicle is started,
and the Orange LED surrounding the transceiver button will
flash every ten seconds while the vehicle is running.
2) When you arrive at the vehicle, turn the ignition key to the
ON position (not the spring loaded start position), then step
on the brake pedal to disengage the remote starter. The
vehicle will continue to run, but now on its own power.
NOTE: The engine will stop running before the pre-programmed
run cycle has expired if you perform any one of the following
functions:
-Press the button on the keychain transmitter two times within 2 seconds
-Depress the brake pedal
-Open the vehicle's hood
-Move the safety control switch to the Off position.
PUSH-BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY CONTROL SWITCH
The Push-Button LED switch located in the receiver allows you to temporarily disable the remote
starting function of the system. This recommended whenever the vehicle is being serviced. To place
the system in the service mode:
1) With the system disarmed/unlocked, and the ignition switch off, Press and Hold the Push-Button
switch found on the windshield receiver, in.
2) Turn the ignition switch on, off, on, off, on, off.
3) The Orange LED begins to flash two short flashes followed by one long flash and continues this
pattern until the unit is returned to the normal mode of operation.
The above action puts the unit into the Remote Start Override/Service mode and will not start from
the RF transmittor or any other input, Posse or otherwise.
To Exit Remote Start Override Mode
1) With the system disarmed, Press and Hold the Push-Button switch found on the windshield
receiver, in.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED turns off indicating that the Remote Start unit is fully functional once again.
UNLOCKING THE VEHICLE:
If you have electric door lock, and the Optional Unlock feature was added, with the vehicle running
under command of the remote start unit, press and hold the transmitter button for 3 seconds until
the doors unlock.
TELEMATIC UPGRADE:
This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that
can give you control of certain functions of your vehicle from a Telephone, or in some cases a
computer interface. Please check with your installation center for most recent Telematic Upgrades. If
you had a Telematic Upgrade installed, the manual supplied with the upgrade unit will provide a
operator's manual advising of the features of the system and means available to control these
features of your vehicle.
.FUNCTION SETTING CHART To be completed by installer
Run Time 5 Min 10 Min 15 Min 20 Min
Lights Pulse Steady

Produkt Specifikationer

Mærke: Audiovox
Kategori: Sikkerhed
Model: PRO-9056TW Pursuit Series

Har du brug for hjælp?

Hvis du har brug for hjælp til Audiovox PRO-9056TW Pursuit Series stil et spørgsmål nedenfor, og andre brugere vil svare dig


Sikkerhed Audiovox Manualer

Audiovox

Audiovox AS9233ST Manual

22 August 2024
Audiovox

Audiovox Prestige Platinum APS 686T Manual

21 August 2024
Audiovox

Audiovox APS-45 Manual

21 August 2024
Audiovox

Audiovox PRO-9056TW Pursuit Series Manual

21 August 2024
Audiovox

Audiovox APS 675 Prestige Platinum Manual

21 August 2024

Sikkerhed Manualer

Nyeste Sikkerhed Manualer

Aritech

Aritech SHATTERPRO 3 Manual

15 Januar 2025
Axis

Axis Camera Station S9001 Mk II Desktop Terminal Manual

15 Januar 2025
Eminent

Eminent EM6511 Manual

15 Januar 2025
Ranex

Ranex RX2567-Z Manual

11 Januar 2025
NetworX

NetworX NX-595E IP Communication Module Manual

5 Oktober 2024
Provision-ISR

Provision-ISR NVR2-4100P Manual

23 September 2024
Gira

Gira 0342 Manual

23 September 2024
Unitron

Unitron Smart Alert Systeem Manual

23 September 2024
Netatmo

Netatmo Welcome Manual

21 September 2024
NetworX

NetworX NX-408 Manual

20 September 2024