AXESS AXGMLN-10 Manual


Læs gratis den danske manual til AXESS AXGMLN-10 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10 anmeldelser. Har du et spørgsmål om AXESS AXGMLN-10, eller vil du spørge andre brugere om produktet?

Side 1/4
AXGMLN-10
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 5/12/20 INSTAXGMLN-10
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
INTERFACE COMPONENTS
OPTIONAL ACCESSORIES (sold separately)
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties • Small flat-blade screwdriver
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................3
Programming .........................................................3
Adjustments ...........................................................3
Troubleshooting .....................................................3
GM Data Interface 2016-Up
APPLICATIONS
CHEVROLET
Colorado (with IOB radio) 2017-Up
Cruze (with IOA radio) 2016-2018
Cruze Hatchback (with IOA radio) 2016-2018
Equinox (with IOB radio) 2018
Malibu (with IOA radio) 2016-2018
Silverado 2016-2018(with IOB radio)
Silverado 2019LD
GMC
Canyon (with IOB radio) 2017-2018
Sierra (with IOB radio) 2016-2018
Sierra Limited (with IOB radio) 2019
• AXGMLN-10 interface • AXGMLN-10 harness
• 16-pin harness with stripped leads
Extension Harness: AXEXH-GM10
Steering Wheel Control Interface: AXSWC
The IOA/IOB code, if applicable, can be found in the label located:Service Parts Identification
Glovebox: Canyon/Colorado/Cruze/Equinox/Silverado/SierraRear Compartment Floor: Malibu
INTERFACE FEATURES
Provides accessory power (12-volt 10-amp)
Retains R.A.P. (retained accessory power)
Provides NAV outputs (parking brake, reverse, speed sense)
Retains chimes
Pre-wired AXSWC harness (AXSWC sold separately)
Retains OnStar / OE Bluetooth
Retains the factory backup camera†
Adjustable chime/OnStar level
• Can be used in both amplified and non-amplified models (excluding Bose)
Retains balance and fade
Micro-B USB updatable
† Excluding 2018 trucks
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle
specific applications
2
CONNECTIONS
From the 16-pin harness with stripped leads to the aftermarket radio:
Connect the wire to the accessory wire.Red
If installing an AXSWC (sold separately), there will be an accessory wire on the Note:
AXGMLN-10 harness to connect as well.
If
the vehicle is equipped with a factory amplifier (excluding Bose), connect the wire Blue/White
to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier
.
If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
If the aftermarket radio has a mute wire, connect the wire to it. If the mute wire is Brown
not connected, the radio will turn off when OnStar is activated.
Connect the wire to the right front positive speaker output.Gray
Connect the Gray/Black wire to the right front negative speaker output.
Connect the wire to the left front positive speaker output.White
Connect the wire to the left front negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the VSS/speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Connect the wire to the parking brake wire.Light Green
Tape off and disregard the following (4) wires, they will not be used in this application.
Green Green/Black Purple Purple/Black, , ,
From the AXGMLN-10 harness to the aftermarket radio:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the battery wire.
If installing an AXSWC (sold separately), connect the wire to accessory power.Red
Connect the wire to the left rear positive speaker output.Green
Connect the wire to the left rear negative speaker output.Green/Black
Connect the wire to the right rear positive speaker output.Purple
Connect the wire to the right rear negative speaker output.Purple/Black
The Black/Yellow wire is used for OnStar level adjustment for models that do not come equipped
with steering wheel controls. See the OnStar level Adjustment section for further instructions
.
If retaining the factory backup camera, connect the Yellow RCA jack to the reverse camera input
.
12-pin AXSWC harness & 3.5mm jack:
The 12-pin AXSWC harness & 3.5mm jack are to be used with an AXSWC (sold separately) to
retain steering wheel audio controls. If the AXSWC is not being used, disregard this harness and
3.5mm jack. If it is to be used, please refer to the AXSWC instructions for radio connections and
programming. Disregard the harness that comes with the AXSWC.
Note: The relay attached to the AXGMLN-10 harness is only for audible turn signal clicks. No extra
steps are required to retain this feature, so leave the relay as-is.


Produkt Specifikationer

Mærke: AXESS
Kategori: Ikke kategoriseret
Model: AXGMLN-10

Har du brug for hjælp?

Hvis du har brug for hjælp til AXESS AXGMLN-10 stil et spørgsmål nedenfor, og andre brugere vil svare dig