Bauknecht B7I HT58 TC Manual

Bauknecht Opvaskemaskine B7I HT58 TC

Læs gratis den danske manual til Bauknecht B7I HT58 TC (24 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Bauknecht B7I HT58 TC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/24
ENDaily Reference Guide
1
CONTROL PANEL
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Rapid program Prewash programbutton with indicator light/ - 3 sec. press
4. Crystals program button with indicator light/ Self-Clean program
- 3 sec. press
5. Auto programs Auto Intensive - buttons with indicator lights / 65°
Auto Mixed Auto Fast / 55° 50°
6. Salt reservoir empty indicator light
7. Rinse Aid reservoir empty indicator light
8. Display
9. Program number remaining time and indicator
10. Closed water tap indicator light
11. DESCALE indicator light
12. Extra options Half Load/ Silent/ Sani Rinse buttons with indicator lights -
13. Power Clean® option button with indicator light
14. Extra Dry option Settings button with indicator light / - 3 sec. press
15. Delay option button with indicator light
16. START/Pause button with indicator light
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.bauknecht.eu/register
Before using the appliance carefully read Safety
and Installation Instructions. More information about your product
available on website: docs.bauknecht.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.
SETTING MENU
1. Switch on the appliance by pressing the button.ON-OFF
2. Hold the (Extra Dry button for 3 seconds, until you hear Settings )
a beep and the display shows „ ”.SEt
3. After one second therst available setting (letter „h”) will be displayed.
4. Press Auto programs / Extra options buttons to scroll through the
list of available settings (see table below), then press START/Pause to
view and change the value of currently selected setting.
5. Press Auto programs / Extra options to change the value, then
press START/Pause to save the new value.
6. To change another setting, repeat points 2 and 5.
7. Press or wait 30 seconds to exit the menu.ON-OFF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and the
machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light - on the con
trol panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 0,5 kg); it is not
unusual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
LETTER SETTING VALUES
(Default - )in bold
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”) 0 | 1 | 2 | 3 | 4 | 5
ActiveDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Time on the oor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Sound
“1” = On, “0” = O 1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
The factory setting is “ 3”. See „WATER HARDNESS TABLE”.
To change, follow instructions in section „SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently
preventing scale buildup on the heater, contributing also to better cleaning
eciency. This system regenerates itself with salt, therefore it is required
to rell the salt container when empty. The frequency of regeneration
depends on the water hardness level setting - regeneration takes place once
per 4-6 Eco cycles with the water hardness level set to 3. The regeneration
process occurs at the beginning of the cycle with additional fresh water.
• Single regeneration consumes: ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be lled A
when the in the control panel is lit.RINSE AID REFILL indicator light
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max. 110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
A
B
FIRST TIME USE
1 2 3 4 5 6 7 10 11 128 9 13 14 15 16
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (Soft) 0 - 6 0 - 10 0 - 7
2 (Medium) 7 - 11 11 - 20 8 - 14
3 (Average) 12 - 16 21 - 29 15 - 20
4 (Hard) 17 - 34 30 - 60 21 - 42
5 (Very hard) 35 - 50 61 - 90 43 - 62
DISPLAY ON THE FLOOR
1
3
2
1. Delay Time on the oor - indicator of the time left to the start of the cycle, when the Delay option is set
2. Salt reservoir empty - indicator light on the oor
3. Remaining Time on the oor - indicator of the time left to the end of the cycle

Produkt Specifikationer

Mærke: Bauknecht
Kategori: Opvaskemaskine
Model: B7I HT58 TC

Har du brug for hjælp?

Hvis du har brug for hjælp til Bauknecht B7I HT58 TC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine Bauknecht Manualer

Bauknecht

Bauknecht BKO PBM Manual

29 Oktober 2025
Bauknecht

Bauknecht B8I HT58 TS Manual

30 September 2025
Bauknecht

Bauknecht BKSV1 FAM Manual

16 September 2025
Bauknecht

Bauknecht BKO FBM Manual

25 August 2025
Bauknecht

Bauknecht B0B D651A X Manual

25 August 2025
Bauknecht

Bauknecht OBFC Ecosilent 8650 Manual

24 August 2025
Bauknecht

Bauknecht OBIC Ecosilent 8650 Manual

16 August 2025
Bauknecht

Bauknecht B7F HS51 X Manual

3 August 2025
Bauknecht

Bauknecht BK6IC11BS7LSA0CH Manual

15 Juli 2025
Bauknecht

Bauknecht BK8IA15AM3TUSC0CH Manual

15 Juli 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Big Chill

Big Chill BC24DWCSNSS Manual

30 Oktober 2025
Big Chill

Big Chill BC24DWCSNPB Manual

29 Oktober 2025
Gram

Gram DS 6300 Manual

29 Oktober 2025
Haier

Haier HDW13F0PS2 Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCPMB Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCBBCW Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCPSS Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCPSB Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWRCR Manual

29 Oktober 2025
Big Chill

Big Chill BC24DWCCRSB Manual

29 Oktober 2025