Bauknecht BKO FBM Manual


Læs gratis den danske manual til Bauknecht BKO FBM (20 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Bauknecht BKO FBM, eller vil du spørge andre brugere om produktet?

Side 1/20
EN
Daily Reference Guide
1
THANK YOU FOR BUYING ABAUKNECHT PRODUCT.
In order to receive amore complete assistance, please
register your appliance on: www.bauknecht.eu/register
PLEASE SCAN THE
QR CODE ON YOUR
APPLIANCE IN
ORDER TO HAVE
MORE DETAILED
INFORMATION
Before using the appliance carefully read Safety and Installation Instructions.
After installation, please remember to remove all transport protection parts from
the dishwasher.
APPLIANCE
PRODUCT DESCRIPTION
CONTROL PANEL
1. ON-OFF/Reset button
with indicator light
2. PREVIOUS program button
3. NEXT program button
4. FAVOURITE program button with indicator light
5. Salt reservoir empty indicator light
6. Rinse Aid reservoir empty indicator light
7. DESCALE indicator light
8. Closed Water Tap indicator light
9. Key lock indicator light
10. Program number and remaining time indicator
11. Display
12. PowerClean Pro option button with indicator light
13. Half Load option button with indicator light/ Settings - 3 sec. press
14. Extra Dry Option button with indicator light/ Keylock - 3 sec. press
15. Delay option button with indicator light
16. START/Pause button with indicator light
1. NaturalDry
2. Top rack
3. Foldable aps
4. Upper rack
5. Upper rack height adjuster
6. Upper sprayer arm
7. PowerClean Pro support
8. Lower rack
9. Cutlery basket
10. PowerClean Pro
11. Lower sprayer arm
12. Filter Assembly
13. Salt reservoir
14. Detergent and Rinse Aid dispensers
15. Rating plate
16. Control panel
1
3
4
5
6
7
8
10
11
16
2
9
12
13
14
15
The control panel of this dishwasher activates pushing by ON/OFF button.
For energy saving the control panel deactivates automatically after 10 minutes if no cycle has started.
W11617756 panel top
W11616949 panel
W11616929 button R
W11616835 button L
W11609979 display
1 2 3 4
11 12 13
14
15
5 6 7 8 9 10
3 sec. 3 sec.
P
16
EN
Daily Reference Guide
2
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining
elastic elements from the upper rack.
SETTING MENU
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings
(Half Load ) button for 3 seconds, until you hear
a beep and the display shows SEt”.
3. After one second the rst available setting (letter h”) will be displayed.
4. Press PREVIOUS
/NEXT to scroll through the list of available settings
(see table below), then press START/Pause
to view and change the
value of the currently selected setting.
5. Press PREVIOUS
/NEXT to change the value, then press START/
Pause
to save the new value and return to the main menu.
LETTER
SETTING
VALUES
(Default - in bold)
Water Hardness Level (see “SETTING THE WA-
TER HARDNESS” and “WATER HARDNESS TABLE”)
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 | 4 | 5
NaturalDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Sound
“1” = On, “0” = O
1 | 0
Factory Settings - press START/Pause to re-
store to the factory default all the values of the
settings included in the settings menu.
-
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components. The salt reservoir is located in the
lower part of the dishwasher (under the lower rack on the left side).
It is mandatory that the salt reservoir never be empty.
It is important to set the water hardness.
Salt must be lled when the SALT REFILL indicator light
on the control
panel is lit.
1. Remove the lower rack and unscrew the reservoir
cap (anticlockwise).
2. Position the funnel (see gure) and ll the salt res-
ervoir right up to its edge (approximately 0,5 kg);
it is not unusual for alittle water to leak out.
3. Only the rst time you do this: ll the salt res-
ervoir with water.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water sof-
tener beyond repair).
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle to avoid
corrosion.
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher
detergent.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that the
water hardness setting is based on the actual water hardness in your house.
This information can be obtained from your local water supplier. The facto-
ry setting is 3”. See „WATER HARDNESS TABLE”.
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (Soft) 0 - 6 0 - 10 0 - 7
2 (Medium) 7 - 11 11 - 20 8 - 14
3 (Average) 12 - 16 21 - 29 15 - 20
4 (Hard) 17 - 34 30 - 60 21 - 42
5 (Very hard) 35 - 50 61 - 90 43 - 62
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on the heater, contributing also to better cleaning ef-
ciency. This system regenerates itself with salt, therefore it is required
to rell the salt container when empty.
The frequency of regeneration depends on the water hardness level setting
- regeneration takes place once per 4-6 Eco cycles with the water hardness
level set to 3.
The regeneration process occurs at the beginning of the cycle with addi-
tional fresh water.
Single regeneration consumes ~3 L of water;
Takes up to 5 additional minutes for the cycle;
Consumes below 0.005kWh of energy.
A
B
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier.
The rinse aid dispenser A should be lled
when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pull-
ing up the tab on the lid.
2. Pour in the rinse aid (max. 110 ml), making
sure it does not overow from the dispens-
er. If this happens, clean the spill immedi-
ately with adry cloth.
3. Press the lid down until you hear aclick to
close it.
NEVER pour the rinse aid directly into the
appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow the instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied.
The LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 6 levels can be set according to the dishwasher model.
If you see bluish streaks on the dishes, set a low number (0-3).
If there are drops of water or limescale marks on the dishes, set a mid-
range number (4-5).
FIRST TIME USE


Produkt Specifikationer

Mærke: Bauknecht
Kategori: Opvaskemaskine
Model: BKO FBM

Har du brug for hjælp?

Hvis du har brug for hjælp til Bauknecht BKO FBM stil et spørgsmål nedenfor, og andre brugere vil svare dig