Bauknecht B8I HF58 TUSC Manual

Bauknecht Opvaskemaskine B8I HF58 TUSC

Læs gratis den danske manual til Bauknecht B8I HF58 TUSC (28 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Bauknecht B8I HF58 TUSC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/28

ENDaily Reference Guide

THANK YOU FOR BUYING A BAUKNECHT PRODUCT.

In order to receive a more complete assistance, please

4 5 6 7 8 9 10 13 14 1511 12 16 17 18 191 2 3 20 21 22

1. button with indicator lightON-OFF/Reset

2. Eco program button with indicator light

3. Auto Intensive program button with indicator light

4. Auto Mixed program button with indicator light

5. Auto Fast program button with indicator light

6. button with indicator lightRapid program

7. Crystals program button with indicator light/ - 3 sec. pressSelf-Clean program

8. Prewash program button with indicator light

9. reservoir empty indicator lightSalt

10. reservoir empty indicator lightRinse Aid

11. Display

12. and Program number remaining time indicator

13. indicator lightClosed water tap

14. indicator lightDESCALE

15. Power Clean® option button with indicator light

16. button with indicator lightHalf Load option

17. button with indicator light/ - 3 sec. pressExtra Dry option Settings

18. button with indicator lightSilent option

19. button with indicator lightSani Rinse option

20. Turbo option button with indicator light

21. button with indicator lightDelay option

22. START/Pause button with indicator light

SETTING MENU

1. Switch on the appliance by pressing the button.ON-OFF

2. Hold the Settings (Extra Dry ) button for 3 seconds, until you hear

a beep and the display shows „SEt”.

3. After one second the rst available setting (letter „ ”) will be displayed.h

4. Press Prewash program / Power Clean® option buttons to scroll

through the list of available settings (see table below), then press START/

Pause to view and change the value of currently selected setting.

5. Press Prewash program / Power Clean® option buttons to

change the value, then press START/Pause to

save the new value.

6. To change another setting, repeat points 2 and 5.

7. Press or wait 30 seconds to exit the menu.ON-OFF

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and on

the machine’s functional components.

The salt reservoir is located in the lower part of the dishwasher (under the

lower rack on the left side).

• It is mandatory that the salt reservoir never be empty.

• It is important to set the water hardness.

• Salt must be lled when the SALT REFILL indicator light on the control

panel is lit. 1. Remove the lower rack and unscrew the reservoir cap

(anticlockwise).

2. Position the funnel and ll the salt reservoir (see gure)

right up to its edge (approximately 0,5 kg); it is not un-

usual for a little water to leak out.

3. Only the rst time you do this: ll the salt reservoir

with water.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly so that no detergent can get into

the container during the wash program (this could damage the water

softener beyond repair).

LETTER SETTING VALUES

(Default - )in bold

Water Hardness Level

(see “SETTING THE WATER HARDNESS”

and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53

Rinse Aid Level

(see “ADJUSTING THE DOSAGE OF RINSE AID”)

0 | 1 | 2 | 3 |

4 | 5

ActiveDry (see “OPTIONS AND FUNCTIONS”)

“1” = On, “0” = O 1 | 0

Time on the oor (see “OPTIONS AND FUNCTIONS”)

“1” = On, “0” = O 1 | 0

Sound

“1” = On, “0” = O 1 | 0

Internal Lights (see “OPTIONS AND FUNCTIONS”)

“1” = On, “0” = O

1 | 0

Factory Settings

Press START/Pause to restore to the factory

default all the values of the settings included in

the settings menu.

Run a program every time as soon as you completed relling the salt

reservoir to avoid corrosion.

Setting the water hardness

To allow the water softener to work in a perfect way, it is essential that the water

hardness setting is based on the actual water hardness in your house. This infor-

mation can be obtained from your local water supplier. The factory setting is “3”.

See „WATER HARDNESS TABLE”.

To change, follow instructions in section “SETTING MENU”.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indicator

light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher detergent.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently preventing

scale buildup on the heater, contributing also to better cleaning eciency.

This system regenerates itself with salt, therefore it is required to rell

the salt container when empty. The frequency of regeneration depends

on the water hardness level setting - regeneration takes place once per 4-6

Eco cycles with the water hardness level set to . The regeneration process 3

occurs at the beginning of the cycle with additional fresh water.

• Single regeneration consumes ~3L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A

lled when the RINSE AID REFILL indicator light in the control panel is lit.

1. Open the dispenser B by

pressing and pulling up the

tab on the lid.

2. Pour in the rinse aid (max.

110 ml), making sure it does

not overow from the dis-

penser. If this happens, clean

the spill immediately with a

dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 (Soft) 0 - 6 0 - 10 0 - 7

2 (Medium) 7 - 11 11 - 20 8 - 14

3 (Average) 12 - 16 21 - 29 15 - 20

4 (Hard) 17 - 34 30 - 60 21 - 42

5 (Very hard) 35 - 50 61 - 90 43 - 62

Before using the appliance carefully read

Safety and Installation Instructions. More information about your

product available on website: docs.bauknecht.eu

After installation, please remember to remove all transport protection

parts from the dishwasher.

CONTROL PANEL

FIRST TIME USE

DISPLAY ON THE FLOOR

1. Delay Time on the oor - indicator of the time left to the start of the cycle, when the Delay option is set.

2. Salt reservoir empty - indicator light on the oor

3. Remaining Time on the oor - indicator of the time left to the end of the cycle

Produkt Specifikationer

Mærke:	Bauknecht
Kategori:	Opvaskemaskine
Model:	B8I HF58 TUSC
Bredde:	598 mm
Dybde:	555 mm
Højde:	820 mm
Indbygget skærm:	Ja
Placering af apparat:	Fuldt indbygget
Indvendig belysning:	Ja
Installationsrum bredde:	608 mm
Installationsrum dybde:	560 mm
Støjniveau:	38 dB
Forsinket start-timer:	Ja
Justerbare fødder:	Ja
Dør farve:	Sort
Vandforbrug pr. cyklus:	9.5 L
Bestik rum type:	Kurv og skuffer
Antal kuverter:	14 kuverter
Cyklustid:	240 min.
Opvaskeprogrammer:	Express, Glass/delicate, Silent
Halv belastning:	Ja
Indikator for afspændingsmiddel:	Ja
Energieffektivitetsskala:	A til G
Selvrensende:	Ja
Indikator for resterende tid:	Ja
Installationsrum højde (min.):	820 mm
Installationsrum højde (maks.):	900 mm
Produktstørrelse:	Fuld størrelse (60 cm)
Støjemissionsklasse:	A
Energieffektivitetsklasse:	B
Energiforbrug pr. 100 cyklusser:	64 kWh
Temperatur (maks):	- °C
Saltindikator:	Ja
Øverste kurv indstillelig højde:	Ja
Kurves indstillelige placering:	Øvre
Antal kurve:	2 kurv(e)
Automatisk døråbning:	Ja
Whirlpool-teknologier (opvaskemaskine):	Maxi Space Tub, Natural Dry, Powerclean Pro