Bazooka BPB24-G2 Manual

Bazooka Højttaler BPB24-G2

Læs gratis den danske manual til Bazooka BPB24-G2 (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Bazooka BPB24-G2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

3 .

4. 5. 6. 7. 8. 9. 10.

11.

12.

Remove fuse from 6 ft power cable (12). Attach the red wire to the positive battery terminal. Attach the black wire

to the negative battery terminal. Run power cable to the location of the BPB24. making sure power wire does not

hinder the safe operation of the vehicle. Plug the red power cable end into the BPB24’s red input power plug. The

black 12vdc accessory plug can be used to power any 12vdc accessory up to 15 amps. Use the included black

accessory pigtail (11) to wire your accessories.

1. Party Bar (BPB24, BPB24-DS, or BPB36) 1 ea.

2. Optional Mounting Bolt 6mm 4 ea.

3. Mounting Leg 2 ea.

4. Rubber Vibration Insulation Pads 2 ea.

5. Socket Head Cap Screw 8mm X 12mm 2 ea.

6. Low Profile Socket Head Cap Screw 6mm X 12mm 2 ea.

7. Socket Head Cap Screw 6mm X 30mm 2 ea.

8. Narrow Washer 6mm 4 ea.

9. Nylon Insert Locking Nut 6mm 2 ea.

10. Stud 6mm x 40mm 2 ea.

11. Accessory Pigtail 1 ea.

12. Power Cable 6 ft. 1 ea.

IMPORTANT NOTICE:

The internal RF circuit for the remote control will draw a small amount of current because it must always be ON

listening for the remote commands. Over time this could draw down your battery when your machine remains in

storage without being connected to a charger or not being actively used. For this reason, we recommend

connecting the Party Bar to a switched master power source or disconnecting the main power wire when the

machine is in storage. We also make a plug & play inline 12v master power switch that can be easily added to the

main battery wire for the Party Bar to completely kill power to the unit. It is listed under the Accessories tab on the

Party Bar product page on our website (Model number: PR-ILS16)

When using the Intergrated Mounting Rail System,

first determine your mounting stud spacing then screw

the 6mm X 40mm studs (10) into the mounting nuts. Mark

your desired spacing onto the flat surface to which you are

mounting. Use a 1/4” or 7mm drill bit to drill mounting holes.

Mount the Party Bar to your mounting surface using the 6mm

washers (8) and 6mm nylon locking nuts (9) provided in

hardware kit. You can also use our optional PR-URM, PR-FRC175,

and PR-FRC200 clamps (sold separately) to mount to round

tubbing. When mounting the bottom half of the clamps to

the Party Bar, you will need to use the 2 ea. 6mm X 12mm low

profile socket head cap screws. (6)

Use the 8mm X 12mm bolts (5) to attach

the mounting legs. Mounting legs (3) can

be installed in ether direction depending

on space constraints. When mounting with

opional clamps (PR-URM, PR-FRC200, and

PR-FRC175) use the hex bolts provided with

the clamps to mount the bottom half of the

clamps to the mounting legs.

PR-FRC200 2” Clamp

PR-FRC175 1.75” Clamp PR-URM 2” - 1.5” Clamp

Warning:

If you are using the cast aluminum mounting legs to secure the Party Bar to your machine, the mounting legs must

FIRST be attached and tightened to the Party Bar before mounting it to your machine. Attaching the legs to the

machine first and then inserting the Party Bar between them can cause misalignment, spacing, and torque issues

that can cause damage to the mounting assembly resulting in a failure.

Intergrated Mounting Rail Options

See Warning Below!

End Mounting Options

with Cast Aluminum Legs

BPB24 / BPB24-DS

BPB36

Installation Instructions

Rev.12/12/2016 Pg. 1

Rev.12/12/2016 Pg. 4

BPB24 / BPB24-DS

BPB36

Installation Instructions

PR-FRC200 2” Clamp

PR-FRC175 1.75” Clamp

PR-URM 2” - 1.5” Clamp

Aux Input Audio Output

Rev. 12/12/2016 Pg. 3

Rev.12/12/2016 Pg. 2

Button 1

Auxiliary 12vdc output on/off switch.

Button 2 Press and hold to power on, press while power is on to switch input

between aux. and Bluetooth inputs, Press and hold to power off.

Button 3 Press to go forward one track, Press and hold to increase volume.

Button 4

Button 5 Press to go back one track, Press and hold to decrease volume.

Aux. Input Used for a 1/8” audio cable

Aud io Output Used for line level audio signal to an amplifier

Press to play/pause, Press to answer/hang up phone, Double

press for last number radial or open Siri on Iphone, Press and

hold to unpair bluetooth device.

Bluetooth module audio indicators:

Audio Response

Power on:

Power off:

Beep:

Double Beep:

Module is turned on

Module is turned off

After LED light stops blinking means module is paired

When play/pause button is pressed and held means

module is unpaired from Bluetooth device.

When forward button is pressed and held means

module has reached maximum volume.

Description

Switch 1 On/Off

Remote switch buttons 2-4 are not used with this model

Switch aux. 12vdc (15 amp) ouput.

LED light status indicator:

LED Light Description

Blinking: Bluetooth module is pairing

Solid blue: Bluetooth module is paired

Blue/Red: Bluetooth module is in AUX

input mode

Led Mic.

Note: * When pressing for Power Off, be sure to hold until Power Off is indicated (audible). Failure to do so

may toggle the Bluetooth Receiver into AUX/BT Mode and it will remain in the last selected mode on subsequent Power On.

If this occurs, simply press the M button again to reselect BT or AUX mode as desired. The receiver should automatically pair

with the last device in BT mode. To pair a new device, press and hold the Play/Pause button.

BPB24 / BPB24-DS

BPB36

Installation Instructions

BPB24 / BPB24-DS

BPB36

Installation Instructions

Produkt Specifikationer

Mærke:	Bazooka
Kategori:	Højttaler
Model:	BPB24-G2

Har du brug for hjælp?

Hvis du har brug for hjælp til Bazooka BPB24-G2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Bazooka Manualer

Bazooka BPB36-G2 Manual

30 Oktober 2024

Bazooka MBTA10250D Manual

30 Oktober 2024

Bazooka BPB24-G3 Manual

24 Oktober 2024

Bazooka BPB24-G2 Manual

24 Oktober 2024

Bazooka MBTA8100 Manual

23 Juli 2024

Bazooka UT6200RL Manual

21 Juli 2024

Bazooka MAC6502BLED-4PK Manual

20 Juli 2024

Bazooka MT8265W Manual

20 Juli 2024

Bazooka MAC6510W Manual

20 Juli 2024

Bazooka MT8100W Manual

20 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer

SoundTube RF31-EZ-T Manual

30 Juli 2025

Valcom VIP-480AL-W-SA Manual

30 Juli 2025

Rockustics StoneHenge II-S/T Manual

30 Juli 2025

Valcom InformaCast VIP-428A-IC Manual

30 Juli 2025

Valcom InformaCast VIP-431A-IC Manual

30 Juli 2025

Electro-Voice Evid 4.2T Manual

30 Juli 2025

Audiocase S10 Manual

30 Juli 2025

JLab JBuds Party Manual

30 Juli 2025

Valcom InformaCast VIP-411A-IC Manual

30 Juli 2025

FoneStar MOV-684PR-L Manual

30 Juli 2025