Bazooka BPB36-G2 Manual

Bazooka Højttaler BPB36-G2

Læs gratis den danske manual til Bazooka BPB36-G2 (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Bazooka BPB36-G2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
1.
3 .
4. 5. 6. 7. 8. 9. 10.
11.
12.
2.
Remove fuse from 6 ft power cable (12). Attach the red wire to the positive battery terminal. Attach the black wire
to the negative battery terminal. Run power cable to the location of the BPB24. making sure power wire does not
hinder the safe operation of the vehicle. Plug the red power cable end into the BPB24’s red input power plug. The
black 12vdc accessory plug can be used to power any 12vdc accessory up to 15 amps. Use the included black
accessory pigtail (11) to wire your accessories.
1. Party Bar (BPB24, BPB24-DS, or BPB36) 1 ea.
2. Optional Mounting Bolt 6mm 4 ea.
3. Mounting Leg 2 ea.
4. Rubber Vibration Insulation Pads 2 ea.
5. Socket Head Cap Screw 8mm X 12mm 2 ea.
6. Low Profile Socket Head Cap Screw 6mm X 12mm 2 ea.
7. Socket Head Cap Screw 6mm X 30mm 2 ea.
8. Narrow Washer 6mm 4 ea.
9. Nylon Insert Locking Nut 6mm 2 ea.
10. Stud 6mm x 40mm 2 ea.
11. Accessory Pigtail 1 ea.
12. Power Cable 6 ft. 1 ea.
IMPORTANT NOTICE:
The internal RF circuit for the remote control will draw a small amount of current because it must always be ON
listening for the remote commands. Over time this could draw down your battery when your machine remains in
storage without being connected to a charger or not being actively used. For this reason, we recommend
connecting the Party Bar to a switched master power source or disconnecting the main power wire when the
machine is in storage. We also make a plug & play inline 12v master power switch that can be easily added to the
main battery wire for the Party Bar to completely kill power to the unit. It is listed under the Accessories tab on the
Party Bar product page on our website (Model number: PR-ILS16)
When using the Intergrated Mounting Rail System,
first determine your mounting stud spacing then screw
the 6mm X 40mm studs (10) into the mounting nuts. Mark
your desired spacing onto the flat surface to which you are
mounting. Use a 1/4” or 7mm drill bit to drill mounting holes.
Mount the Party Bar to your mounting surface using the 6mm
washers (8) and 6mm nylon locking nuts (9) provided in
hardware kit. You can also use our optional PR-URM, PR-FRC175,
and PR-FRC200 clamps (sold separately) to mount to round
tubbing. When mounting the bottom half of the clamps to
the Party Bar, you will need to use the 2 ea. 6mm X 12mm low
profile socket head cap screws. (6)
Use the 8mm X 12mm bolts (5) to attach
the mounting legs. Mounting legs (3) can
be installed in ether direction depending
on space constraints. When mounting with
opional clamps (PR-URM, PR-FRC200, and
PR-FRC175) use the hex bolts provided with
the clamps to mount the bottom half of the
clamps to the mounting legs.
PR-FRC200 2” Clamp
PR-FRC175 1.75” Clamp PR-URM 2” - 1.5” Clamp
Warning:
If you are using the cast aluminum mounting legs to secure the Party Bar to your machine, the mounting legs must
FIRST be attached and tightened to the Party Bar before mounting it to your machine. Attaching the legs to the
machine first and then inserting the Party Bar between them can cause misalignment, spacing, and torque issues
that can cause damage to the mounting assembly resulting in a failure.
Intergrated Mounting Rail Options
See Warning Below!
End Mounting Options
with Cast Aluminum Legs
BPB24 / BPB24-DS
BPB36
Installation Instructions
Rev.12/12/2016 Pg. 1
Rev.12/12/2016 Pg. 4
BPB24 / BPB24-DS
BPB36
Installation Instructions
PR-FRC200 2” Clamp
PR-FRC175 1.75” Clamp
PR-URM 2” - 1.5” Clamp

Produkt Specifikationer

Mærke: Bazooka
Kategori: Højttaler
Model: BPB36-G2

Har du brug for hjælp?

Hvis du har brug for hjælp til Bazooka BPB36-G2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Bazooka Manualer

Bazooka

Bazooka BPB36-G2 Manual

30 Oktober 2024
Bazooka

Bazooka MBTA10250D Manual

30 Oktober 2024
Bazooka

Bazooka BPB24-G3 Manual

24 Oktober 2024
Bazooka

Bazooka BPB24-G2 Manual

24 Oktober 2024
Bazooka

Bazooka MBTA8100 Manual

23 Juli 2024
Bazooka

Bazooka UT6200RL Manual

21 Juli 2024
Bazooka

Bazooka MAC6502BLED-4PK Manual

20 Juli 2024
Bazooka

Bazooka MT8265W Manual

20 Juli 2024
Bazooka

Bazooka MAC6510W Manual

20 Juli 2024
Bazooka

Bazooka MT8100W Manual

20 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Sven

Sven G600 Manual

27 December 2025
Sven

Sven MC-15 Manual

27 December 2025
Wharfedale

Wharfedale Diamond 12.4I Manual

25 December 2025
Sven

Sven PS-375 Manual

24 December 2025
Phoenix Gold

Phoenix Gold ZP8 Manual

24 December 2025
BoomTone DJ

BoomTone DJ SOUNDBLAZE 600 Manual

23 December 2025
Sven

Sven MC-25 Manual

23 December 2025
Wharfedale

Wharfedale Diamond 12.Ci Manual

23 December 2025
Wharfedale

Wharfedale Diamond 12.3i Manual

23 December 2025
Wharfedale

Wharfedale Elysian 3 Manual

23 December 2025