Bazooka MT8265B Manual

Bazooka Højttaler MT8265B

Læs gratis den danske manual til Bazooka MT8265B (7 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 68 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 34.5 anmeldelser. Har du et spørgsmål om Bazooka MT8265B, eller vil du spørge andre brugere om produktet?

Side 1/7

Center top of Tubbie

mounting plate with bottom

of clamp. Loosen saddle

clamp latching bolt until

nut is 1/8” from end of

threaded mounting

stud. Wrap saddle

clamp around bottom

of clamp and top of

Tubbie mounting plate.

Tighten latch bolt.

Place clamp on mounting pipe. Minimum

distance from edge of clamp to nearest

obstruction is 7”(177.8 mm). If clamp is

mounted any closer, the Tubbie will not be

able to rotate 360 degrees. Make sure

clamp is level, then mark pipe so a hole

can be drilled for the wires. Hole should be

between 1/2” (12.7mm) & 3/4” (19.5 mm).

Remove clamp & drill hole.

Extend the length of the PCB

wires so they will be able to

reach your audio source.

Run wires through bottom of clamp and through

your mounting pipe. Reattach clamp to make

sure wires are centered in the mounting hole.

MTCL3-S, MTCL2-S, MTCL2-B

Southern Audio Services 1-800-THE-TUBE or 225-272-7135 www.bazooka.com Canadian customers contact: Trends Electronics International Inc. 604-988-2966 or 877-946-9255

Remove PCB board if already installed

in bottom of clamp.

MT8100B / MT8100W

S ingle ended Tubbies :

Red -Speaker positive

Black - Speaker negative

Gray - NA

White - NA

MT81LKB / MT81LKW

S ingle ended Tubbies w/ light kit

Red -Speaker positive

Black - Speaker negative

Gray - 12vdc positive

White - 12 vdc negative

MT8265B / MT265W

Double ended Tubbies

Dual 4 ohm configuration

Red -Speaker positive

Black - Speaker negative

Gray - Speaker negative

White - Speaker positive

MT8265B / MT265W

Double ended Tubbies

Single 2 ohm configuration

Combine Red and White Speaker positives

Combine Black and Gray Speaker negative

Pipe Clamp

Top

Pipe Clamp

Bottom

2 ea. 6 mm

socket head

cap screws

Clamp PCB

Saddle Clamp

Retaining

clip Latch Bolt

Plastic

Inserts

Latch bolt can be loosened

and tighten by hand to be

able to rotate Tubbie. If you

want a more permanent

mount, tightened with a

10mm wrench or supplied

allen wrench. Ether way

always make sure clamp

is tight and retaing clip

is in place before

boat is in motion.

Parts per Clamp

Produkt Specifikationer

Mærke:	Bazooka
Kategori:	Højttaler
Model:	MT8265B

Har du brug for hjælp?

Hvis du har brug for hjælp til Bazooka MT8265B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Bazooka Manualer

Bazooka BPB36-G2 Manual

30 Oktober 2024

Bazooka MBTA10250D Manual

30 Oktober 2024

Bazooka BPB24-G3 Manual

24 Oktober 2024

Bazooka BPB24-G2 Manual

24 Oktober 2024

Bazooka MBTA8100 Manual

23 Juli 2024

Bazooka UT6200RL Manual

21 Juli 2024

Bazooka MAC6502BLED-4PK Manual

20 Juli 2024

Bazooka MT8265W Manual

20 Juli 2024

Bazooka MAC6510W Manual

20 Juli 2024

Bazooka MT8100W Manual

20 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer

DS18 PRO-TW920 Manual

28 September 2025

Turbosound TQ8-YB Manual

28 September 2025

Turbosound KT15-HP Manual

27 September 2025

IHome iBT32 Manual

27 September 2025

Helix Compose Ci3 C100.2FM-S3 MK2 Manual

27 September 2025

Gear4 PG731EUK Manual

27 September 2025

IHome iBT29 Manual

27 September 2025

IHome iHSI-W400BT-PR-BLK Manual

27 September 2025

Turbosound TQ12-SB Manual

27 September 2025

Turbosound TCS218B-AN Manual

27 September 2025