Benro HD1A Manual

Benro Stativ HD1A

Læs gratis den danske manual til Benro HD1A (2 sider) i kategorien Stativ. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Benro HD1A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

75 Virginia Road

North White Plains, NY 10603

T 914.347.3300

F 914.347.3309

info@BenroUSA.com

BenroUSA.com

HD Series 3-Way Panhead

Operating Instructions

Thank you for making Benro your choice for professional photographic

equipment. Your Benro gear is manufactured to provide years of

dependable service. In order to obtain optimum satisfaction and

performance, we suggest that you carefully read these instructions.

Speciﬁcations and design are subject

to change without notice.

1 2

Quick Release Plate

Horizontal Tilt Lock

Plate Locking Lever

Pan Lock

Base

Mounting Screw

Front/Rear Tilt Lock

Security Locking Lever

Bubble Level

SETUP

Head Mounting

Install by screwing the head clockwise onto

the 3/8" Mounting Thread of the Top Plate of

the Tripod or Monopod. Once it is hand tight,

secure by fully tightening the Head Locking

Screw(s) (on select models) from below.

OPERATION

Three-way positioning of camera and

lens movement is directly controllable

on the HD Series 3-Way Panheads. Two

comfortable Handles provide both

movement and locking of front to rear

Tilt, and side to side Tilt. Plus, a separate

Locking Knob permits the entire Head

assembly to move freely within a 360°

rotational adjustment.

Quick Release Plate

The HD Series 3-Way Panheads incorporate

a Quick Release Plate system. It offers a

quick method of mounting or releasing a

Camera or Equipment from the Head. It’s

important that the correct Quick Release

Plate be used along with the proper

mounting screw (1/4–20 is included as the

standard size but spare 1/4–20 and 3/8

plates are available as accessories). Extra

Plates are recommended as you can screw

one to each Camera or Lens for even greater

convenience when rapidly mounting and

dismounting gear.

Quick Release Locking Lever (FIGURES 1 & 2)

When used properly, the patented Dual

Lock Quick Release system offers two levels

of security for your gear. To remove the

Quick Release Plate, squeeze both the Plate

Locking Lever and the Security Locking

Lever and pull the larger Locking Lever

out. The Quick Release Plate will disengage

allowing it to be removed.

To reconnect the Quick Release Plate, insert

the angled part of the Plate into the groove

on the opposite side of the Locking Levers

and press down flat. The Locking Levers will

automatically engage the locking system and

will return to the safety lock position. Press

the Plate Locking Lever in firmly to secure.

Pan Control (FIGURE 3)

Horizontal rotation or Panning can be easily

accomplished by first loosening the Pan Lock

and then rotating Head on Platform. Once

in position tighten the Pan Lock securely.

NOTE: Do not over tighten the Pan Lock as

this could damage the locking mechanism.

Tilt Control (FIGURE 4)

Front to Rear Angle or Tilt adjustments can

be easily accomplished by first loosening

the Tilt Lock (be sure to hold on firmly to

balance weight of the camera). Position as

required and then tighten Handle securely.

You have the same Control and Lock

available on the other axis for Horizontal

Angle or Tilt adjustments.

NOTE: Do not over tighten the Tilt Locks as

this could damage the locking mechanism.

FOR ADDITIONAL CONTROL: Depending

on your requirements you may find it

convenient to reorient the camera or lens

90° on the Quick Release Plate and remount

so that the Tilt Controls give you different

positioning support.

USER NOTICE

• Do not exceed the maximum specified

load capacity (see specifications at

www.BenroUSA.com).

• Always ensure that all Panhead locks are

tightly engaged before mounting any gear.

• Always clean and dry any Panhead after

it has been exposed to wet, dusty, sandy

or salty conditions. Your Panhead is not

recommended for use in salt water. If

required, clean Panhead using a mild

soap solution applied with a soft cloth,

rinse with fresh water and dry with soft

towel. Remove any dust, dirt or sand from

all locks and all moving parts.

• Do not leave any Panhead in the sun

for prolonged periods and avoid high

temperature exposure.

• Avoid leaving any Tripod or Monopod

unattended in areas where people could

trip over the gear and get hurt.

• Remove camera, lens, and all gear from any

Tripod or Monopod when transporting.

• For your safety, don’t let your Benro

gear come in contact with any electrical

power source.

3 4

Operating Instructions & User Notice

Produkt Specifikationer

Mærke:	Benro
Kategori:	Stativ
Model:	HD1A

Har du brug for hjælp?

Hvis du har brug for hjælp til Benro HD1A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Stativ Benro Manualer

Benro S4 Pro Manual

8 December 2024

Benro S8Pro Manual

8 December 2024

Benro S2Pro Manual

8 December 2024

Benro ITrip FIT19AIH0 Manual

7 Oktober 2024

Benro BV4PRO Manual

2 Oktober 2024

Benro KH25N Manual

20 September 2024

Benro Video Monopod A48FDS4 Manual

7 September 2024

Benro HD3A Manual

4 September 2024

Benro C2573FS4 Manual

1 September 2024

Benro Adventure Monopod MAD49A Manual

4 August 2024

Stativ Manualer

Nyeste Stativ Manualer

Glide Gear G2H 100 Manual

3 April 2025

Sachtler FSB 14T Mk II Manual

2 April 2025

Proaim P-MLAK-01 Manual

2 April 2025

Proaim LV-SCFH-01 Manual

2 April 2025

Proaim P-G-PM Manual

2 April 2025

Proaim P-OHCR-01 Manual

2 April 2025

Proaim P-LLBT-MTCL Manual

2 April 2025

Proaim P-TNGO-01 Manual

2 April 2025

Proaim VI-GLDE-01 Manual

2 April 2025

Oben CT-3431 Manual

2 April 2025