Best MD8T Manual

Best Ikke kategoriseret MD8T

Læs gratis den danske manual til Best MD8T (14 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Best MD8T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/14

MODELS MD6T • MD8T • MD10T

Page 1

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

2. Do not use the unit in conjunction with any exhaust device other

than compatible BEST, Broan Elite or Broan range hoods.

3. This unit is not designed to provide combustion air for fuel-

burning appliances.

4. Do not connect the unit directly to a combustion appliance of

any type.

5. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and

Air Conditioning Engineers (ASHRAE), and the local code

authorities.

6. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

7. When performing installation, servicing or cleaning the unit, it is

recommended to wear safety glasses and gloves.

8. During extreme weather events including snow storms, ensure

that the intake area for the outside air duct is not blocked and

able to provide a clear pathway for outside air to enter the

system.

9. When cutting or drilling into wall or ceiling, do not damage

electrical wiring or other hidden utilities.

10. When notching or drilling into framing including floor supports,

rim joists, and wall studs, comply with code and manufacturer

limitations on allowable modifications to these structural

members.

11. This unit is intended to be installed within the home in a location

protected from moisture.

12. This unit must be in an accessible location which allows for

inspection of the unit.

13. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in this document.

14. When federal, provincial or state legislation comprises more

restrictive installation and/or certification requirements, the

aforementioned requirements prevail on those of this document

and the installer agrees to conform to these at his own expense.

AUTOMATIC

MAKE-UP AIR DAMPER

WITH TRANSFORMER

READ AND SAVE THESE INSTRUCTIONS

FOR RESIDENTIAL USE ONLY

CAUTION

1. Do not locate outside air inlet near hazardous materials or

explosives.

2. Unit shall not be installed to introduce air from crawlspaces,

garages, attics, adjacent dwelling units, or other locations within

the building shell. Unit shall be installed to introduce air directly

from outdoors.

3. Do not run the outside air duct directly above or closer than 2 ft to

any furnace or its supply plenum, boiler, or other heat producing

appliance.

4. Any ductwork used in conjunction with the Damper must be

installed in compliance with all local and national codes that are

applicable.

5. Do not operate the Damper for fresh air introduction until all system

filters, including the central duct system filter, have been installed

per the system design.

6. Please read the unit specification label on the product for further

information and requirements.

7. The Damper’s outdoor air intake, ducting, and any filters should be

inspected and maintained on a regular basis.

8. Insulate the duct and damper to prevent build-up of condensation

in cold weather climates. Vapor barriers on both sides of insulation

are recommended.

To register this product

visit: www.broan.com

Produkt Specifikationer

Mærke:	Best
Kategori:	Ikke kategoriseret
Model:	MD8T

Har du brug for hjælp?

Hvis du har brug for hjælp til Best MD8T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Best Manualer

Best HBN536212SS Manual

25 August 2025

Best HARKBN36 Manual

8 Juli 2025

Best HBN554212SS Manual

25 Februar 2025

Best HBN542912SS Manual

25 Februar 2025

Best HBN536912SS Manual

24 Februar 2025

Best HBN33696SS Manual

24 Februar 2025

Best HBN548212SS Manual

24 Februar 2025

Best HBN33096SS Manual

24 Februar 2025

Best HBN560212SS Manual

24 Februar 2025

Best HBN224812SS Manual

24 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JET TPFA-Z Manual

15 December 2025

Crosley Asheville CF1149 Manual

15 December 2025

Mercusys MC200 Manual

15 December 2025

Growatt ARK 2.5L-A1 Manual

15 December 2025

ALNO MC40244 Manual

15 December 2025

BEKO BG640EXVIXL Manual

15 December 2025

Milwaukee 48-22-9200 Manual

15 December 2025

Growatt ALP 5.0L-E1-AU Manual

15 December 2025

Arçelik A55 A 950 A Manual

15 December 2025

Extron EBP 106 Manual

15 December 2025