Blade BLH8645 Manual

Blade Radiostyret legetøj BLH8645

Læs gratis den danske manual til Blade BLH8645 (2 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 60 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 30.5 anmeldelser. Har du et spørgsmål om Blade BLH8645, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1 2 3

• Models are hazardous when operated and maintained incorrectly.

• Always install and operate a radio control system correctly.

• Always pilot a model so the model is kept under control in all

conditions.

• Please seek help from an experienced pilot or your local hobby

store.

• Contact local or regional modeling organizations for guidance and

instructions about  ying in your area.

• When working with a model, always power on the transmitter  rst

and power off the transmitter last.

• After a model is bound to a transmitter and the model is set up in

the transmitter, always bind the model to the transmitter again to

establish failsafe settings.

• Always make sure all batteries are fully charged before  ying.

• Time  ights so you can  y safely within the time allotted by your

battery.

• Perform a range check of the transmitter and the model before

 ying the model.

• Make sure all control surfaces correctly respond to transmitter

controls before  ying.

• Do NOT  y a model near spectators, parking areas or any other

area that could result in injury to people or damage to property.

• Do NOT  y during adverse weather conditions. Poor visibility, wind,

moisture and ice can cause pilot disorientation and/or loss of

control of a model.

• When a  ying model does not respond correctly to controls, land

the model and correct the cause of the problem.

Age Recommendation:

Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to

become familiar with the features of the product

before operating. Failure to operate the product

correctly can result in damage to the product, personal

property and cause serious injury.

This is a sophisticated hobby product. It must be operated

with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe

and responsible manner could result in injury or damage to

the product or other property. This product is not intended for

use by children without direct adult supervision. Do not use

with incompatible components or alter this product in any

way outside of the instructions provided by Horizon Hobby,

LLC. This manual contains instructions for safety, operation

and maintenance. It is essential to read and follow all the

instructions and warnings in the manual, prior to assembly,

setup or use, in order to operate correctly and avoid damage

or serious injury.

The following terms are used throughout the product

literature to indicate various levels of potential harm when

operating this product:

NOTICE: Procedures, which if not properly followed, create

a possibility of physical property damage AND a little or no

possibility of injury.

CAUTION: Procedures, which if not properly followed, create

the probability of physical property damage AND a possibility

of serious injury.

WARNING: Procedures, which if not properly followed, create

the probability of property damage, collateral damage, and

serious injury OR create a high probability of super cial injury.

NOTICE

All instructions, warranties and other collateral documents are

subject to change at the sole discretion of Horizon Hobby, LLC. For

up-to-date product literature, visit horizonhobby.com and click on

the support tab for this product.

Meaning of Special Language

WARNING: Failure to exercise caution while using this

product and comply with the following warnings could

result in product malfunction, electrical issues, excessive heat,

FIRE, and ultimately injury and property damage.

• Read all safety precautions and literature prior to use of this product

• Never allow minors to charge battery packs

• Never drop charger or batteries

• Never attempt to charge damaged batteries

• Never attempt to charge a battery pack containing different types

of batteries

• Never charge a battery if the cable has been pinched or shorted

• Never allow batteries or battery packs to come into contact with

moisture at any time

• Never charge batteries in extremely hot or cold places (recom-

mended between 50–80 degrees F or 10–27 degrees C) or place

in direct sunlight

• Always disconnect the battery after charging, and let the charger

cool between charges

• Always inspect a new battery before charging

• Always terminate all processes and contact Horizon Hobby if the

product malfunctions

• Always keep batteries and charger away from any material that

could be affected by heat (such as ceramic and tile), as they can

get hot

• Always end the charging process if the charger or battery

becomes hot to the touch or starts to change form (swell) during the

charge process

Charging Warnings

General Notes

Pilot Safety

www.KnowChroma.comBLH8645

M A N U A L

W I Z A R D

1. Aircraft Mode LED

2. Wizard GPS LED

3. Aircraft Status LED

4. Ascend / Forward Button

5. Rotate / Fly Left Button

6. Rotate / Fly Right Button

7. Descend / Backward Button

8. Magic Button

9. Camera Tilt Down

10. Camera Tilt Up

11. Start / Stop Motors Button

12. Wizard Power Button

13. Wizard Power LED

14. Smart / AP / Home Mode

Switch

15. Clip

16. USB Port

Control Layout

Speciﬁ cations

LED Codes

Aircraft Mode LED

Smart Mode: LED solid green

AP Mode: LED solid purple

Home Mode: LED solid red

‘Point-N-Fly’ Function Activated: LED solid blue

‘Follow Me’ Function Activated: LED solid yellow

Wizard GPS LED

GPS Locked: LED solid green

Aircraft Status LED

Wizard not bound: LED solid red

GPS Loss of Aircraft: LED off

Battery full: LED solid green

Battery 50%: LED blinking green twice every 2 seconds

Battery 25%: LED blinking green once every 2 seconds

Low Voltage Warning of the Aircraft:

LED blinking red quickly, the Wizard vibrates

for 2 seconds

Wizard Power LED:

Powered On: LED solid green

During Charging: LED solid red

Charging Completed: Red LED off

Low Voltage Warning of the Wizard:

Low Battery: LED blinking green twice every 2 seconds

Low Voltage: LED blinking green once every 2 seconds

Power Cut-off: LED blinking red quickly, the Wizard

vibrating for 2 seconds once continuously.

Dimensions: 5.47 X 1.46 X 0.98 in (139 X 37 X 25 mm)

Weight: 2.52 oz (71.5 g)

Built-In LiPo Battery Voltage/Capacity: 3.7V 500mAh

Approximate Working Time: 3.5 h

Compatible Aircfraft*: Blade®

Chroma™

Compatible Camera: CGO2, CGO2+, CGO3

Water Resistant: Yes

* This transmitter is not compatible with Spektrum DSM

®, DSM2® or

DSMX® technology equipped aircraft.

This transmitter is not compatible with Spektrum DSM

®, DSM2® or

DSMX® technology equipped aircraft.

Blade, Chroma, DSM, DSM2, DSMX, Point-N-Fly and the Horizon Hobby logo

are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

Created 09/15 51112 (EN) BLH8645

Three ﬂ ight modes are available using the

Wizard, Smart Mode, Angle (AP) Mode and

Home Mode.

To change ﬂ ight modes, change the position

of the ﬂ ight mode slider to the desired ﬂ ight

mode.

Smart Mode

The aircraft mode LED glows solid green.

While in Smart Mode, the quadcopter is

geo-fenced to no further than 300 feet

(90 meters) away from the Wizard.

While in Smart Mode, the ﬂ ight controls

function relative to the pilot position.

Point-N-Fly™ Function

NOTICE: The recommended ﬂ ying height is 10-20m. The

operating range of the Wizard is 10-50m.

This function is only available while Smart Mode is enabled.

Point the Wizard in the direction you wish the quadcopter to

ﬂ y.

Press and hold the Magic Button until the Aircraft Mode LED

glows solid blue and the wand vibrates once.

Tilt the wand from 0° – 90° to control the distance away

desired. The closer to 0°, the farther away from you the

quadcopter will travel. The closer to 90°, the closer to you

the quadcopter will travel. When the wand is held at 90°, the

quadcopter will ﬂ y close to you and hold at a safe distance.

To exit Point-N-Fly, press any direction control button. The

quadcopter will stop moving and hold its position, if a suitable

GPS signal is held, and maintain a level attitude.

Tracking Function

Tracking enables the camera to track the position of the

Wizard, adjusting the tilt angle of the gimbal and the yaw

of the quadcopter to keep the wand position in frame. The

Rotate Left and Rotate Right functions are disabled while the

Tracking function is active, however the Fly Left and Fly Right

functions are still available.

Tracking is the default function while in Smart Mode.

To return to the Tracking Function from the Follow Me

Function, press the Magic Button once. The Aircraft Mode LED

will glow solid green.

Follow Me Function

With the Follow Me Function enabled, the quadcopter will

follow the movement of the Wizard. To enable the Follow Me

function, press the Magic Button quickly once. The Aircraft

Mode LED will glow solid yellow, indicating Follow Me is

enabled. All controls function normally while the Follow Me

function is enabled. You must use the ﬂ ight controls to keep

the camera oriented in the desired direction.

CAUTION: The maximum ﬂ ight speed of the

Chroma™ quadcopter is approximately 18 mph.

If the movement of the pilot and Wizard exceeds 30 mph,

the aircraft may crash or experience a “ﬂ y away,” neither of

which are covered under warranty.

Angle Mode (AP Mode)

The aircraft mode LED glows solid purple.

While in Angle Mode (AP Mode), the ﬂ ight controls function

relative to the quadcopter’s orientation. Point to Fly, Watch

Me and Follow Me functions are disabled while Angle Mode

is active.

NOTICE: Do not allow the quadcopter to travel farther than

200m from the Wizard. If the aircraft exceeds 200m away,

the Wizard will vibrate until the quadcopter is ﬂ own back to

within 200m.

Charge the Wizard (~2 hours)

Powering On the Wizard

Binding the Wizard to the Chroma

Flight Controls

Flight Modes

Starting and Stopping the Motors

Calibration Procedures

Troubleshooting

CAUTION: Refer to the Charging Warnings section.

All instructions and warnings must be followed

exactly. Mishandling of Li-Po batteries can result in a ﬁ re,

personal injury and/or property damage.

Power off the Wizard. Using the USB cable provided, connect

the Wizard to a suitable USB power source.

Power LED Indications

Power On: Solid Green

Charging: Solid Red

Charging Complete: Off

NOTICE: Storing the fully charged Wizard for extended periods

of time may damage the installed LiPo battery. The wand should

be stored in a partially discharged state.

NOTICE: Do not remove the installed LiPo battery. Battery

removal may damage the wand and will void the warranty.

Press and hold the Power Button. When the LEDs blink once

and the Wizard vibrates once, release the Power button. The

Power LED glows solid green, and the Aircraft Mode LED is on,

showing the currently selected ﬂ ight mode color.

The Wizard must be bound to the Chroma quadcopter for

proper operation. To bind or re-bind your quadcopter to Wizard,

follow the directions below.

1. With the transmitter and quadcopter powered OFF, connect

the battery to the quadcopter.

2. Place the quadcopter on a ﬂ at level surface.

3. Power the quadcopter ON and let it initialize. The status

LEDs will remain off.

4. Hold the quadcopter upside down until the status LEDs ﬂ ash

blue, indicating it has entered bind mode.

5. Set the quadcopter back

upright.

6. Press and hold the Wizard

power button until the Aircraft

Mode LED glows solid blue.

7. Shake the Wizard up and down

as shown until the quadcopter

beeps twice, indicating binding

is successful.

8. Release the power button.

The Wizard controls different aspects of the quadcopter’s ﬂ ight

by changing the orientation of the wand.

Holding the wand between 50° and 90°, as shown, enables

the control functions shown below:

Push and hold the Motor Start/Stop button to start

the motors. When you have completed your ﬂ ight,

you may either use Home Mode to land and stop

the motors, or land manually and press the Motor

Start/Stop button after the quadcopter is on the ground.

If the quadcopter is 20 ft above the Wizard, hold the below

stop button for to stop the motors.1.5 seconds

If the quadcopter is 20 ft above the Wizard, hold the above

stop button for to stop the motors.3 seconds

NOTICE: Do not press the Motor Stop button while the aircraft is

airborne. The motors could stop, causing the aircraft to crash.

WARNING: Stopping the motors while the quadcopter

is still in ﬂ ight will cause the quadcopter to crash.

Crash damage is not covered under warranty.

90°

50°

0°

90°

40°

0°

Holding the wand between 0° and 40°, as shown, enables

the control functions shown below:

Ascend

Fly forward

Descend

Fly backward

Rotate right

Fly right

Rotate left

Fly left

Home Mode

The Aircraft Mode LED glows solid red.

When Home Mode is activated, the quadcopter will ﬂ y in a

straight line in the direction of the pilot. If the quadcopter is

below 30 ft when Home Mode is activated, it will climb above

30 ft prior to returning to the pilot. The quadcopter will return

to within 4-8m from the pilot, land and stop the motors. Pay

attention to the prospective landing area when the quadcopter

begins its descent. The ﬂ y forward, ﬂ y backward, ﬂ y left

and ﬂ y right buttons may be used, while the quadcopter is

descending, to re-position it to a safe landing area if needed.

NOTICE: During the controlled descent, the ﬂ ight controls

function relative to the quadcopter’s orientation, similar to

Angle Mode.

Point-N-Fly, Tracking and Follow Me functions are disabled

while Home Mode is active.

To exit Home Mode before the quadcopter lands, change

the ﬂ ight mode slider to Smart or Angle (AP) Mode. The

quadcopter will stop and hold its position, if it has a suitable

GPS lock, and maintain a stable attitude.

CAUTION: Do not activate Home Mode if you are in

or near a body of water.

The tilt angle of the camera gimbal

is controlled using the Camera Tilt

buttons on the Wizard.

Photo and video functions are

controlled using your smart device via the mobile application

available from Google Play or the App Store.

NOTICE: The control radius of the camera, under ideal

conditions, is approximately 90m.

Problem Solution

Wizard vibrates continu-

ously after

powering on

Contact customer service

Wizard fails to power on Contact customer service

Aircraft Status LED is solid

yellow or blinking yellow

frequently

Follow the calibration

procedures to calibrate the

Wizard

Power LED ﬂ ashes red

rapidly

Low battery – Follow the

charging procedure to re-charge

the Wizard

For a complete description of the function, capabilities

and maintenance of the Wizard, refer to the online videos at

www.KnowChroma.com.

NOTICE: Magnetic interference may affect the calibration

procedure. It is recommended to calibrate the Wizard

outdoors, away from any magnetic surface.

To enter calibration mode:

Press and hold both the

Descend/Backward Button

and the Power Button

together until the Aircraft

Status LED is solid pink,

approximately 2 seconds.

Release both buttons. If

for any reason the Wizard

does not enter calibration

mode successfully, power it off and back on again and attempt

to enter calibration mode again.

When the Wizard has

successfully entered

calibration mode, hold it

at arms length with the

buttons facing toward

your body and move it in

a horizontal ﬁ gure-eight

continuously, as shown

in the illustration, rotating the Wizard to follow the path. While

following the ﬁ gure-eight with the Wizard, rotate your body

slowly in a circle. This process should take approximately

30 seconds.

When the calibration process is complete, the Wizard will

automatically power off. The Wizard is now calibrated and may

be powered on and used normally.

If the calibration process fails, the Aircraft Mode LED will glow

solid red and the power LED will rapidly ﬂ ash red. Power the

Wizard off and repeat the calibration process until successful.

For further information on calibrating the Wizard, see the online

videos at www.KnowChroma.com.

Camera Control

Produkt Specifikationer

Mærke:	Blade
Kategori:	Radiostyret legetøj
Model:	BLH8645
Produktfarve:	Orange,White
Indbygget skærm:	Ingen
Produkttype:	Fjernbetjening
Normal brug:	Kameradrone
Kapabilitet:	Chroma