Blaupunkt IPC-S1 Manual

Blaupunkt Overvågningskamera IPC-S1

Læs gratis den danske manual til Blaupunkt IPC-S1 (7 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Blaupunkt IPC-S1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

IP Camera

Parts Description

1 Power LED (Green) .

2 Status LED (Red) .

3. Network LED (Blue)

4. WPS Button

Press and hold for 2 seconds to activate WPS protocol

5. Learning / Privacy Button

Press and hold for 2 seconds to enter/exit privacy mode

Press and hold for 10 seconds to enter learning mode

Press and hold for 6 seconds to exit learning mod

6. Micro SD Card Slot

7. Ethernet Port

8. DC Jack

Package Content

1 x CameraIP

1 x Camera Stand

2 Wall plugs, washer and screws x

1 AC/DC 5V 2A Power Adaptor x

1 x Ethernet Cable

The Camera must be learnt into Control Panel to serve as part IP

of the alarm system.

1. Connect the Ethernet port to the same router as your alarm

system Control Panel.

2. Plug in the AC adaptor to power on.

3. After Blue Network LED lights up, put the Control Panel into

learning mode.

4. Press and hold the Learn button for 10 seconds. Ignore the 2

Red Status LED ﬂash at the 2

nd second and release the button

when the Blue Network LED begins to ﬂash.

5. The Control Panel should display IP Camera info. Refer to

Control Panel manual to complete learning process.

6. If the Control Panel does not display IP Camera info, press and

hold the Learn button for 6 seconds to stop the Blue Network

LED ﬂashing. Then restart from Step 4.

The IP Camera records video when an alarm is activated by other

sensors in the alarm system. It is recommended to deploy the IP

Camera at locations protected by other intrusion detection

sensors to capture video of intruders after an alarm is activated.

For example, deploy the camera to point at door/window

protected by Door Contact, or to cover an area protected by PIR

Sensor.

A camera stand is provided in the package for IP Camera

installation.

 T camera stand is made of the base, shaft and head. he

 The camera head includes following part:

Collar: When the IP Camera is installed on the mounting screw,

turn the collar counter-clockwise to loosen or clockwise to

tighten the mounting screw into IP Camera.

Knob: Turn the Knob counter-clockwise to loosen the mounting

screw and adjust camera angle, then clockwise to tighten.

Cap: When adjusting the camera angle, make sure the bottom of

the cap should ﬁt around the stand and does not leave any gap.

1. Use the mounting holes on the base as template to mark

mounting location on the wall.

2. Drill holes on the wall and insert wall plug if required.

3. Screw the base into the mounting location.

4. Connect the camera stand head, shaft and base.

Learning

Installation

Collar

Knob

Cap

Mounting Holes

Camera Stand Hole

ENGLISH

Produkt Specifikationer

Mærke:	Blaupunkt
Kategori:	Overvågningskamera
Model:	IPC-S1
Type:	IP-sikkerhedskamera
Bredde:	82 mm
Dybde:	41.4 mm
Højde:	93 mm
Produktfarve:	Hvid
Kompatible hukommelseskort:	MicroSD (TransFlash)
Wi-Fi:	Ja
Understøttede videotilstande:	720p,1280p
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Wi-Fi-standarder:	802.11b,802.11g,Wi-Fi 4 (802.11n)
Understøttede videoformater:	H.264
Driftstemperatur (T-T):	-10 - 45 °C
Maksimal opløsning:	1280 x 720 pixel
Sikkerhedsalgoritmer:	AES,TKIP,WEP,WPA,WPA2,WPS
Understøttede grafikopløsninger:	1280 x 720 (HD 720)
Forbindelsesteknologi:	Kabel & trådløs
Indbygget HDD:	Ingen
Video komprimeringsformater:	H.264
Understøttet placering:	Indendørs
Frekvensbånd:	2.4 GHz
Sensortype:	CMOS
Samlet antal megapixels:	1.3 MP
Videoopløsninger:	1280 x 720 pixel
Optisk zoom:	- x
Grænseflade:	RJ-45
Dag/nat funktion:	Ja
Minimumsbelysning:	- Lux
Fast brændvidde:	1.6 mm
Nattesyn:	Ja
Billedhastighed:	30 fps
Bevægelsessensor (video):	Ja
Brændviddeområde:	0 - 4.2 mm
Bevægelsessensor:	Ja