Bobrick B-5191 Manual

Bobrick Ikke kategoriseret B-5191

Læs gratis den danske manual til Bobrick B-5191 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Bobrick B-5191, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

continued . . .

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 1/08/18

S/D

Printed in U.S.A.

Technical Data

14-7/16''

365mm

5-15/16''

150mm

11-7/8''

300mm

18''

455mm

2-1/4''

55mm

Dia.

Bolt Circle

1-1/8''

30mm

2-1/4''

55mm

Base Plate

with Spring

Guide Bracket

Finish Face of Floor

Support

Bracket

15-3/8''

390mm

4-3/8''

110mm

1-3/8''

35mm

5-1/2''

140mm

Finish Face of Wall

15-13/16''

400mm

Mounting

Flange (2)

Concealed

Wall Backing

to Comply with

Local Building Codes

Not Furnished

by Bobrick

*Consult local building codes

9-3/8''

240mm

7-1/4''

185mm

3-1/16''

75mm

11''

280mm

Universal/Accessible Design

Recommended

Mounting Height

*17'' to 19''

430 to 485mm

MATERIALS:

Seat — One-piece, 5/16" (8mm) thick, solidly fused plastic laminate with matte-ﬁnish melamine surfaces, ivory-colored face

sheets, and black phenolic-resin core that are integrally bonded — cannot delaminate. Integral slots for water drainage. Secured

to frame with stainless steel carriage bolts and acorn nuts.

Frame — 18-8, Type-304, stainless steel with satin ﬁnish. 16-gauge (1.6mm), 1-1/4" (30mm) square tubing and 18 -gauge

(1.2mm), 1" (25mm) diameter seamless tubing.

Mounting Flanges (2) — 18-8, Type-304, 3/16" (5mm) thick stainless steel with satin ﬁnish. 3" (75mm) diameter with three

mounting screw holes.

Baseplate — 18-8, Type-304, heavy-gauge stainless steel.

Spring — 17-7, Type-301, 24-gauge (0.6mm) stainless steel. Spot-welded to baseplate.

Guide Bracket — 18-8, Type-304, 16-gauge (1.6mm) stainless steel with satin ﬁnish.

SOLID PHENOLIC

FOLDING

SHOWER/DRESSING

AREA SEAT

B-5191

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-5191 r1/08/18 Printed in U.S.A.

OPERATION:

Shower seat can be folded up against the wall when not in use. The spring at the top of baseplate holds seat into upright position

until released by pulling the top of seat away from wall. Bobrick Folding Shower Seats are not spring-loaded. The seats do not

return automatically to the upright position after use. Support system with guide bracket allows varying mounting heights and

leaves ﬂoor clear for easier cleaning. Nonporous solid phenolic seat has slots to permit water to drain, does not splinter or re-

quire oiling, and will not support growth of bacteria. Slotless round-head carriage bolts and acorn nuts provide additional safety

to user. Bobrick shower seats, when properly installed, have sufﬁcient strength to support 500 lbs., (227 kg) complying with

accessible design guidelines (including ADAAG in the U.S.A.).

INSTALLATION:

Secure unit to wall at points indicated by an , with the two mounting ﬂanges located at top and the baseplate and guide bracket S

below. The bottom of support bracket must be positioned between the baseplate and guide bracket before they are secured to

wall or partition. Mounting height of shower seat must comply with local building codes.

For stud walls, provide concealed backing to comply with local building codes and secure with #14 x 2-1/2" (6.3 x 65mm)

stainless steel sheet-metal screws furnished by manufacturer.

For prefabricated shower stalls, provided adequate backing by the shower stall manufacturer. Secure with #14 x 2-1/2"

(6.3 x 65mm) stainless steel mounting screws furnished by manufacturer. Bobrick offers a mounting kit for installing shower

seats. For additional mounting kits please order 252-30. One mounting kit is required for each ﬂange.

For masonry walls, provide ﬁber plugs or expansion shields for use with furnished sheet-metal screws, or provide 1/4" (6mm)

toggle bolts or expansion bolts.

INSTALL SAFETY PLATE TO WALL:

Safety Plate is to be mounted on wall near Shower Seat in order to properly advise users of the Seat's weight restrictions.

Correct installation of the Safety Plate will ensure that the Shower Seat meets A.N.S.I. Standards.

Permanently afﬁx Safety Plate to wall on either side of the Shower Seat at a minimum height of 30" (760mm). If mounted above

Seat, the Plate must be high enough so that it is not covered when Seat is on the up position. Mounting screws (4) are

recommended, but double-sided tape on rear of Plate may be used for very smooth, non-porous surfaces.

SAFETY WARNING: Shower seats are no stronger than the anchors and walls to which they are attached and

must be ﬁrmly secured in order to support the loads for which they are intended. Consult and comply with local

building codes. To avoid potential injury, the building owner or maintenance personnel should remove the shower

seat from service if the shower seat is not adequately secured to the wall. Unit shall support static loads of up

to 500 lbs (227 kg) when properly installed and used. To avoid potential seat malfunction, DO NOT use seat if

weight exceeds 500 lbs (227 kg).

SPECIFICATION:

Folding shower seat shall have a frame constructed of Type-304, satin-ﬁnish stainless steel that consists of 16-gauge (1.6mm),

1-1/4'' (30mm) square tubing and 18-gauge (1.2mm), 1'' (25mm) diameter seamless tubing. Seat shall be one-piece, 5/16"

(8mm) thick, solidly fused plastic laminate with matte-ﬁnish melamine surfaces, ivory-colored face sheets, and black phenolic-

resin core; secured to frame with stainless steel carriage bolts and acorn nuts. Shower seat shall be equipped with two 3''

(75mm) diameter mounting ﬂanges constructed of Type-304, 3/16'' (5mm) thick, satin-ﬁnish stainless steel; a guide bracket

constructed of Type-304, 16-gauge (1.6mm), satin-ﬁnish stainless steel; and a spring constructed of Type-301, 24-gauge (0.6mm)

stainless steel that is spot-welded to a baseplate of Type-304, heavy-gauge stainless steel. Seat shall be able to lock in upright

position when not in use. Shower seat shall comply with accessible design guidelines (including ADAAG in the U.S.A.).

Folding Shower Seat shall be Model B-5191 of Bobrick Washroom Equipment, Inc., Clifton Park, New York;

Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario;

Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

Produkt Specifikationer

Mærke:	Bobrick
Kategori:	Ikke kategoriseret
Model:	B-5191

Har du brug for hjælp?

Hvis du har brug for hjælp til Bobrick B-5191 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Bobrick Manualer

Bobrick B-5191 Manual

5 Juli 2025

Bobrick B-29744 Manual

15 Juni 2025

Bobrick B-2860 Manual

15 Juni 2025

Bobrick B-3944 Manual

15 Juni 2025

Bobrick B-6977 Manual

7 April 2025

Bobrick B-6861 Manual

7 April 2025

Bobrick B-4390 Manual

7 April 2025

Bobrick B-699 Manual

7 April 2025

Bobrick B-9806 Manual

7 April 2025

Bobrick B-5806 Manual

7 April 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

M-Audio iControl Manual

12 September 2025

Steinberg VST Live 2 Manual

12 September 2025

PCE FLEX 16-E Manual

12 September 2025

Tineco iFloor 3 Breeze Manual

12 September 2025

V7 RMWC9UV450-1N Manual

12 September 2025

Parisot Taylor 2319LISU Manual

12 September 2025

Leen Bakker Bergen Manual

12 September 2025

Redragon GA-200 Manual

12 September 2025

DAP-Audio DCP-26 MKII Manual

12 September 2025

Vivax MF-45E Manual

12 September 2025