Bontrager Duotrap S Manual

Bontrager Cykel computer Duotrap S

Læs gratis den danske manual til Bontrager Duotrap S (2 sider) i kategorien Cykel computer. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Bontrager Duotrap S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

• •

DUOTRAP S

ANT+ and Bluetooth Smart Dual Mode

Integrated Speed and Cadence Sensor

•

1•

•

4•

•

m2.5N

MADE IN CHINA

•

m2.5N

•

4 4

a b

SENSOR INSTALLATION (ALLOY BIKES)

SENSOR INSTALLATION (CARBON BIKES)

BATTERY INSTALLATION AND REPLACEMENT

Gasket (alloy bikes)

Remove DuoTrap S cover

from chainstay.

Remove DuoTrap S cover

from chainstay.

Medium cadence

magnet band

(crank)

Install sensor into chainstay.

While holding sensor in

place, use a 2.5mm hex to

tighten .6mm short screw

Note: 6mm screw must be

used with carbon frames.

Remove grommet and

replace with gasket in #3.

Remove grommet.

Hold sensor into place and

install .8mm long screw

Install sensor into grommet in the chainstay. Hint: Hold

grommet in place with one hand while inserting sensor with

the other as seen in pic 4a and 4 b.

Replacement battery

CR2032.

Use a coin to close battery

compartment.

Install gasket onto sensor

with notch aligned with

screw hole as depicted

Fully insert grommet into

chainstay resulting in a ﬂush

connection with chainstay.

While holding sensor in

place, use a 2.5mm hex to

tighten .8mm long screw

Sensor with grommet (carbon bikes)

8mm alloy

bike mounting

screw

6mm carbon

bike mounting

screw

Small cadence

magnet band

(crank)

Large cadence

magnet band

(crank)

CR2032

battery

Alloy bike speed

magnet (wheel)

Cadence band

shim (optional)

Carbon bike speed

magnet (wheel)

•

1•

•

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

-- Consult the dealer or experienced radio / TV technician for help.

NOTES:

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES

OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE GRANTEE OF THIS DEVICE

COULD VOID THE USER’S AUTHORITY TO OPERATE THE DEVICE.

Pairing: Consult your ANT + or Bluetooth Smart device’s instructions for pairing. Sensor

will need to be activated directly before pairing process.

Sensor Activation: To verify proper magnet install, spin wheel or turn crank more than

two revolutions. Initial sensor activation and magnet alignment will be indicated by the

LEDs ﬂashing up to 10 times.

Please Note: The sensor will stay active for at least 2 minutes although the LEDs no

longer ﬂash.

Bluetooth Smart Connection: Install and activate sensor. Turn on your phone’s

(or other compatible device) Bluetooth capability. Open the desired cycling app and follow

instructions for Bluetooth Smart sensor connection. Please note, Bluetooth Smart devices

do not always appear in your phone’s settings, even when connected. All apps collect,

share, and display speed and cadence information differently.

FCC ID: 04GDUOTRAPS

This device complies with part 15 of the FCC Rules.

Operation is subject to the following conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

This device complies with Industry Canada RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired operation

of the device.

Leprésent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils

radio. Exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)

l’appareil ne doit pas produire de brouillage, et (2) l’utilsateur de l’appareil doit accepter

tout brouillage radioélectrque subi, meme si le brouillage est susceptible d’en

compromettre le fonctionnement.

www.bontrager.com

IC: 7666A-DUOTRAPS

Remove the pedal and

install cadence magnet on

nondrive side crank arm

with thick side nearer the

chainstay. Use cadence

magnet band that gives

the best ﬁt.

For carbon bikes, place

magnet 135mm or

145mm from the center

of the bottom bracket to

the center of the magnet.

Hint: If the magnet is aligned

but the LED does not

illuminate, place a cadence

band shim underneath the

appropriate magnet.

Verify magnet is aligned with

sensor by illumination of

green cadence sensor LED

as crank is turned. LED will

illuminate for the ﬁrst 10

revolutions. Align magnet

with tech mark on alloy

bike’s chain stay.

145mm

135mm

SPEED MAGNET INSTALLATION (CARBON AND ALLOY BIKES)

CADENCE MAGNET INSTALLATION (CARBON AND ALLOY BIKES)

PAIRING AND SENSOR ACTIVATION

Speed magnet (carbon

bikes) Snap magnet onto

inside/trailing edge non-drive

side spoke. Some carbon

frame/wheel combinations

may require magnet to be

ﬂipped so the thin side faces

sensor.

Speed magnet (alloy bikes)

Tighten wheel magnet on

spoke for alloy bikes

Align speed magnet with

tech mark on DuoTrap S.

Verify sensor is aligned with

magnet by illumination of red

speed sensor LED as wheel

is rotated. LED will illuminate

for the ﬁrst 10 revolutions.

Produkt Specifikationer

Mærke:	Bontrager
Kategori:	Cykel computer
Model:	Duotrap S

Har du brug for hjælp?

Hvis du har brug for hjælp til Bontrager Duotrap S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykel computer Bontrager Manualer

Bontrager Trip wireless Manual

25 August 2024

Bontrager Trip 1 Manual

25 August 2024

Bontrager Duo Trap S Sensor Manual

24 August 2024

Bontrager Node Manual

24 August 2024

Bontrager Duotrap Manual

6 August 2024

Bontrager Duotrap S Manual

5 August 2024

Bontrager Trip 100 Manual

4 August 2024

Bontrager Trip 300 Manual

27 Juli 2024

Cykel computer Manualer

Nyeste Cykel computer Manualer

Lezyne Micro C Manual

30 December 2025

BBB BCP-35W Manual

12 Oktober 2024

Crivit HG01734A Manual

3 Oktober 2024

Sigma Pure GPS Manual

2 Oktober 2024

Bryton Rider 20 Manual

2 Oktober 2024

Sigma BC 1600 Manual

30 September 2024

Lezyne Mega XL GPS Manual

29 September 2024

Wahoo Elemnt Roam v2 Manual

23 September 2024

Trelock BB 4000i Manual

23 September 2024

Echowell Ui-20 Manual

23 September 2024