Boss GE-7 Manual

Boss Ikke kategoriseret GE-7

Læs gratis den danske manual til Boss GE-7 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Boss GE-7, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another eects unit).

AC Adaptor

(PSA series; sold separately)

Electric Guitar

English

Graphic equalizer

Control 7 octave bands from 100 Hz to 6.4 kHz by 15 dB up or down.

The Graphic Equalizer GE-7 adjusts the harmonic contents of an instrument or microphone in seven separate bands.

It covers the frequency spectrum for electric bass, electric guitar, keyboard, mic, etc., to adjust them for room acoustic or to accent a particular tone range.

Each control adjusts a slightly expanded octave to yield 15 dB of cut or boost.

The rst three bands adjust the fundamental and the higher four bans adjust the strength of the harmonic accent.

In addition level control is very useful for the balance eect sound.

OUTPUT jack

This jack feeds signal to amplier.

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play

without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it

with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the

AC adaptor gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

* If the AC adaptor is connected while power is on, the power supply is

drawn from the AC adaptor.

Indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

* The CHECK indicator shows whether the eect is on or o, and indicates the dierent

functions. It does not indicate whether the power to the device is on or not.

Pedal Switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the

Battery.”

Panel Descriptions

Main Features

Precautions When Connecting

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

* Once the connections have been completed, turn on power

to your various devices in the order specied. By turning on

devices in the wrong order, you risk causing malfunction and/

or damage to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

* Before turning the unit on/o, always be sure to turn the

volume down. Even with the volume turned down, you might

hear some sound when switching the unit on/o. However,

this is normal and does not indicate a malfunction.

Operating the Unit

1. After connecting all cords

required, set all knobs on the

panel as illustrated.

2. Depress the pedal switch

CHECK LED lights to

indicate “EFFECT ON” and

extinguishes to indicate

“EFFECT OFF.”

* This CHECK LED is also used to check

battery. If LED fails to light or becomes

dim, the battery should be replaced.

3. Set Graphic Equalizer sliders

to proper position.

4. While switching pedal ON

and OFF, set Level slider to

proper position so no volume

dierence between Normal

and Eect modes is notices.

Use of Battery

* A battery was installed in the unit before it left the factory. The

life of this battery may be limited, however, since its primary

purpose was to enable testing.

* If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES” (supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

* Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent

malfunction and damage.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be

opened without

detaching the

thumbscrew

completely.

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and

battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Main Specications

BOSS GE-7: Equalizer

Nominal Input Level -20 dBm

Input Impedance 470 kΩ

Nominal Output Level -20 dBm

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply DC 9 V: Dry battery 6F22 (9 V) type (carbon),

AC Adaptor (PSA-series: optional)

Current Draw 10 mA

* Expected battery life under continuous use:

Carbon: Approx. 37 hours

Alkaline: Approx. 67 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 450 g/1 lb (including battery)

Accessories Owner’s Manual, Leaet (“USING THE UNIT

SAFELY,” “IMPORTANT NOTES,” and “Informa-

tion”), Dry battery/9 V type (6F22)

Options AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

Level slider

The level allows to control of GE-7’s output loudness so that it can match or

contrast with the straight signal.

* The INPUT jack also serves as the power

switch. Power is turned on whenever a plug

is inserted into the INPUT jack, and is turned

o when the plug is disconnected. When not

using the unit, you should disconnect any

cord connected to the INPUT jack.

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	GE-7

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss GE-7 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

28 November 2025

27 November 2025

1 Oktober 2025

29 September 2025

Boss SDE-3000EVH Manual

18 Juli 2025

Boss VE-22 Manual

25 Februar 2025

Boss SDE-3 Manual

23 Januar 2025

Boss Distortion DS-1X Manual

1 Januar 2025

Boss RC-505MK2 Manual

1 Januar 2025

Boss GM-800 Manual

1 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025