Boss Distortion DS-1X Manual

Boss Ikke kategoriseret Distortion DS-1X

Læs gratis den danske manual til Boss Distortion DS-1X (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Boss Distortion DS-1X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Owner’s Manual

Precautions When Connecting

If you’ll be using the DS-1X for an extended time, we recommend

that you use an AC adaptor. If you prefer to use a battery, we

recommend an alkaline battery.

To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

Once the connections have been completed, turn on power to

your various devices in the order specied. By turning on devices

in the wrong order, you risk causing malfunction and/or damage

to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then

open the pedal upward.

* The pedal can be opened without detaching the thumbscrew

completely.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

2. Remove the old battery from the battery housing, and

remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output

Level

-20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance

10 kΩ or greater

Power Supply Alkaline battery (9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw 60 mA

* Expected battery life under continuous use:

Alkaline: 6 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 440 g / 1 lb (including battery)

Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT

NOTES,” and “Information”)

Alkaline battery (9 V, 6LR61)

Options

(sold separately)

AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Panel Descriptions

English

7This is a cutting-edge distortion eect that is distinctly dierent than previous types of distortion.

7The DS-1X adds the perfect amount of distortion for each frequency region without requiring you to adjust the settings, seamlessly providing the ideal distortionwhether you’re ring on low notes or

playing a lead solo on high notes.

7You’ll be able to adjust your tone easily and intuitively.

Main Features

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

AC Adaptor Jack

Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without

being concerned about how much battery power you have left.

* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the

correct voltage. Do not use any other AC adaptor, since this may cause

malfunction.

* If the AC adaptor is connected while power is on, the power supply is

drawn from the AC adaptor.

* We recommend that you keep batteries installed in the unit even though

you’ll be powering it with the AC adaptor. That way, you’ll be able to

continue a performance even if the cord of the AC adaptor gets accidently

disconnected from the unit.

CHECK Indicator

Shows whether the eect is on or o, and also doubles as the battery check indicator. The

indicator lights when the eect is on.

* If you’re powering the unit with a battery and the CHECK indicator goes dim— or

doesn’t light at all—when you try to turn the eect on, the battery is near

depletion and should be replaced. For instructions on changing the battery, refer

to “Changing the Battery.”

Pedal Switch

This switch turns the eect on/o.

Thumbscrew

When this screw is loosened, the pedal will

open, allowing you to change the battery.

* For instructions on changing the

battery, refer to “Changing the Battery.”

INPUT Jack

Accepts signals coming from a guitar or other musical instrument, or another

eects unit.

* The INPUT jack doubles as the power switch. Power to the unit is turned on

when you plug into the INPUT jack; the power is turned o when the cable

is unplugged. To prevent unnecessary battery consumption, be sure to

disconnect the plug from the INPUT jack when not using the eects unit.

OUTPUT Jack

Connect this jack to your amp or to the input of another eect unit.

AC Adaptor

(PSA series: optional)

Electric Guitar

Guitar Amplier

LEVEL Knob

Adjusts the volume when the eect is on.

LOW Knob

Adjusts the tone quality of the lower range when the eect is on.

HIGH Knob

Adjusts the tone quality of the upper range when the eect is on.

DIST Knob

Adjusts the amount of distortion applied to the sound. Turning the knob

clockwise boosts the distortion eect.

Use of Battery

A battery was installed in the unit before it left the factory. The life

of this battery may be limited, however, since its primary purpose

was to enable testing.

If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY” and

“IMPORTANT NOTES” (supplied on a separate sheet).

When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

Batteries should always be installed or replaced before connecting

any other devices. This way, you can prevent malfunction and

damage.

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	Distortion DS-1X

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss Distortion DS-1X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

28 November 2025

27 November 2025

1 Oktober 2025

29 September 2025

Boss SDE-3000EVH Manual

18 Juli 2025

Boss VE-22 Manual

25 Februar 2025

Boss SDE-3 Manual

23 Januar 2025

Boss Distortion DS-1X Manual

1 Januar 2025

Boss RC-505MK2 Manual

1 Januar 2025

Boss GM-800 Manual

1 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JET TPFA-Z Manual

15 December 2025

Crosley Asheville CF1149 Manual

15 December 2025

Mercusys MC200 Manual

15 December 2025

Growatt ARK 2.5L-A1 Manual

15 December 2025

ALNO MC40244 Manual

15 December 2025

BEKO BG640EXVIXL Manual

15 December 2025

Milwaukee 48-22-9200 Manual

15 December 2025

Growatt ALP 5.0L-E1-AU Manual

15 December 2025

Arçelik A55 A 950 A Manual

15 December 2025

Extron EBP 106 Manual

15 December 2025