Boss SD-1W Manual

Boss Ikke kategoriseret SD-1W

Læs gratis den danske manual til Boss SD-1W (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Boss SD-1W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Owner’s Manual

Precautions When Connecting

5 To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

5 Once the connections have been completed, turn on power to

your various devices in the order specied. By turning on devices

in the wrong order, you risk causing malfunction and/or damage

to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

5 Due to the characteristics of its analog circuitry, this unit’s CHECK

indicator may be lit (eect on) or unlit (eect o) when you turn

the power on.

Use of Battery

5 A battery was installed in the unit before it left the factory. The life

of this battery may be limited, however, since its primary purpose

was to enable testing.

5 If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY” and

“IMPORTANT NOTES” (supplied on a separate sheet).

5 When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

5 Batteries should always be installed or replaced before connecting

any other devices. This way, you can prevent malfunction and

damage.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then

open the pedal upward.

* The pedal can be opened without detaching the thumbscrew

completely.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

2. Remove the old battery from the battery housing, and

remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output

Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply Carbon-zinc battery (9 V, 6F22) or

Alkaline battery (9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw 15 mA

* Expected battery life under continuous use:

Carbon: 25 hours

Alkaline: 42 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 430 g / 1lb (including battery)

Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT

NOTES,” and “Information”)

Alkaline battery (9 V, 6LR61)

Options

(sold separately) AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

English

Main Features

Panel Descriptions

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

INPUT jack

This jack accepts signals coming from a guitar or other musical instrument, or

another eects unit.

* The INPUT jack doubles as the power switch.

Power to the unit is turned on when you plug into the INPUT jack; the

power is turned o when the cable is unplugged.

To prevent unnecessary battery consumption, be sure to disconnect the

plug from the INPUT jack when not using the eects unit.

AC Adaptor

(PSA series: optional)

Electric Guitar

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without

being concerned about how much battery power you have left.

* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the correct

voltage. Do not use any other AC adaptor, since this may cause malfunction.

* If the AC adaptor is connected while a battery is installed, the power

supply is drawn from the AC adaptor.

* We recommend that you keep batteries installed in the unit even though

you’ll be powering it with the AC adaptor. That way, you’ll be able to

continue a performance even if the cord of the AC adaptor gets accidently

disconnected from the unit.

CHECK indicator

This indicator shows whether the eect is on or o, and also doubles as the battery check

indicator. The indicator lights when the eect is on.

* If you’re powering the unit with a battery and the CHECK indicator goes dim— or doesn’t

light at all—when you try to turn the eect on, the battery is near depletion and should be

replaced. For instructions on changing the battery, refer to “Changing the Battery.”

OUTPUT jack

Connect this jack to your amp or to the input of another eect unit.

Pedal switch

This switch turns the eect on/o.

Thumbscrew

When this screw is loosened, the pedal

will open, allowing you to change the

battery.

* For instructions on changing the

battery, refer to “Changing the

Battery.”

LEVEL knob

Adjusts the volume when the eect is on.

TONE knob

Adjusts the brightness of the eect sound. Turning the knob clockwise

brightens the sound.

DRIVE knob

Adjusts the amount of overdrive. Turning the knob clockwise increases the eect

(distortion).

Mode switch

Switches the tonal character.

S (standard) The original tone of the SD-1.

C (custom) A custom tone that broadens the range and slightly

boosts the gain.

7This is a “WAZA CRAFT series” eect unit featuring analog circuitry painstakingly designed in every detail for the best possible sound.

7The amp circuit consists entirely of discrete components; no op-amps are used.

7In addition to the sound of the original SD-1, you’ll enjoy a custom tone that’s been fully tuned-up by BOSS engineers.

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	SD-1W

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss SD-1W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

28 November 2025

27 November 2025

1 Oktober 2025

29 September 2025

Boss SDE-3000EVH Manual

18 Juli 2025

Boss VE-22 Manual

25 Februar 2025

Boss SDE-3 Manual

23 Januar 2025

Boss Distortion DS-1X Manual

1 Januar 2025

Boss RC-505MK2 Manual

1 Januar 2025

Boss GM-800 Manual

1 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025