Boss Super Chorus CH-1 Manual

Boss Ikke kategoriseret Super Chorus CH-1

Læs gratis den danske manual til Boss Super Chorus CH-1 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Boss Super Chorus CH-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another eects unit).

* The INPUT jack doubles as power switch.

Power to the unit is turned on when you

plug into the INPUT jack; the power is

turned o when the cable is unplugged.

When not using the eects unit, be sure

to disconnect the plug from the INPUT

jack.

AC Adaptor

(PSA series; sold separately)

Electric Guitar

English

E.LEVEL knob

This sets the mixing level of the eect sound (whose pitch is changing) to the

normal sound. Clockwise rotation increases the volume of the eect sound, while

counterclockwise rotation decreases it.

7The BOSS CH-1, featuring stereo output system, creates spacious chorus eect.

7Provided with four controls, Eect Level, Equalizer, Rate and Depth, the CH-1 allows wide variety of chorus sounds.

OUTPUT A/B jacks

Connect an amplier to these jacks.

For monaural output, use only Output A.

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play

without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering

it with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of

the AC adaptor gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

* If the AC adaptor is connected while power is on, the power supply is

drawn from the AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

EQ knob

This controls the tone of the eect sound. Clockwise rotation boosts higher

frequencies and counterclockwise rotation cuts them.

Pedal Switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the

Battery.”

Panel Descriptions

Main Features

Precautions When Connecting

5 To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

5 Once the connections have been completed, turn on power to

your various devices in the order specied. By turning on devices

in the wrong order, you risk causing malfunction and/or damage

to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

5 Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

Use of Battery

5 A battery was installed in the unit before it left the factory. The life

of this battery may be limited, however, since its primary purpose

was to enable testing.

5 If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY” and

“IMPORTANT NOTES” (supplied on a separate sheet).

5 When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

5 Batteries should always be installed or replaced before connecting

any other devices. This way, you can prevent malfunction and

damage.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be

opened without

detaching the

thumbscrew

completely.

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and

battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Main Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply Alkaline battery (9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw 55 mA

* Expected battery life under continuous use:

Alkaline: Approx. 6 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 420 g / 15 oz (including battery)

Accessories Leaet (“USING THE UNIT SAFELY,”

“IMPORTANT NOTES,” and “Information”)

Alkaline battery (9 V, 6LR61)

Options AC Adaptor PSA series

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

RATE knob

This sets the rate of the chorus eect. Clockwise rotation quickens the rate and

counterclockwise rotation slows down.

DEPTH knob

This sets the depth of the chorus eect. Clockwise rotation deepens the eect

and counterclockwise rotation creates the opposite eect.

Operating the Unit

1. Make all the necessary

connections, then set the

control knobs on the panel

as shown to the right.

2. Make the CHECK indicator

light up (if it is not lit, press

the pedal switch).

3. Set the desired rate with the

RATE knob.

4. Set the desired depth with

the DEPTH knob.

5. Adjust the tone of the eect

sound with the EQ knob.

6. Set the volume of the eect

sound with E.LEVEL knob.

5 For monaural output, use only OUTPUT A. OUTPUT A sends the

mixture of the eect and normal sounds.

5 When using the CH-1 in stereo output:

OUTPUT A: Only eect sound (whose pitch is changing) is output.

OUTPUT B: Only normal sound is output.

The CH-1 adopts the space compounding stereo system, therefore,

the eect will vary depending on the distance between two

speakers (L/R). Try playing the instrument to check how it actually

sounds like. If you lower the equalizer or eect level, the pan will

be moved to OUTPUT B.

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	Super Chorus CH-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss Super Chorus CH-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

28 November 2025

27 November 2025

1 Oktober 2025

29 September 2025

Boss SDE-3000EVH Manual

18 Juli 2025

Boss VE-22 Manual

25 Februar 2025

Boss SDE-3 Manual

23 Januar 2025

Boss Distortion DS-1X Manual

1 Januar 2025

Boss RC-505MK2 Manual

1 Januar 2025

Boss GM-800 Manual

1 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025