Boss Super Over Drive SD-1 Manual

Boss Ikke kategoriseret Super Over Drive SD-1

Læs gratis den danske manual til Boss Super Over Drive SD-1 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Boss Super Over Drive SD-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another eects unit).

* The INPUT jack also serves as the power

switch. Power is turned on whenever

a plug is inserted into the INPUT jack,

and is turned o when the plug is

disconnected. When not using the

unit, you should disconnect any cord

connected to the INPUT jack.

AC Adaptor

(PSA series; sold separately)

Electric Guitar

English

LEVEL knob

This knob adjusts the level of the eect sounds. Set the knob so there is no

volume dierence between the eect and straight guitar sounds.

Unlike earlier fuzz units, the SD-1 can faithfully express the picking dynamics and subtle nuances of your playing. Regardless of the type of guitar you’re using, the true character of its tone will come through.

This unit generates a soft and clear distortion like that of an overdriven tube amp.

In addition, you can use the tone control to boost or cut the high-frequency range, creating a versatile range of eects.

When the eect is on, the LED is lit, showing at a glance whether the eect is on or o.

OUTPUT jack

The output jack is used to connect the unit to

ampliers or other devices.

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play

without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it

with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the

AC adaptor gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

* If the AC adaptor is connected while power is on, the power supply is

drawn from the AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

* The CHECK indicator shows whether the eect is on or o, and indicates the dierent

functions. It does not indicate whether the power to the device is on or not.

TONE knob

This adjusts the tone of sound. Rotating it clockwise will create sharp sound

with emphasized treble, while turning it counterclockwise will create soft

sound with cut treble.

Pedal Switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the

Battery.”

Panel Descriptions

Main Features

* To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units before making

any connections.

* Before turning the unit on/o, always be sure to turn the volume down. Even with the volume turned down, you might

hear some sound when switching the unit on/o. However, this is normal and does not indicate a malfunction.

DRIVE knob

Adjusts the amount of overdrive. Turning the knob clockwise increases the

eect (distortion).

Owner’s Manual

Operating the Unit

1. After connecting all cords required, set all knobs on

the panel as illustrated.

2. Depress the pedal switch. Check LED lights to indicate

“EFFECT ON” and extinguishes to indicate “EFFECT

OFF.”

* This check LED is also used to check battery. If LED fails to light or

becomes dim, the battery should be replaced.

3. Turn DRIVE knob to proper position.

4. While switching pedal ON and OFF, turn LEVEL knob

to proper position so no volume dierence between

Normal and Eect modes is noticed.

5. Turn TONE knob to proper position.

Use of Battery

* A battery was installed in the unit before it left the factory. The

life of this battery may be limited, however, since its primary

purpose was to enable testing.

* If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES” (supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

* Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent

malfunction and damage.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be

opened without

detaching the

thumbscrew

completely.

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Main Specications

BOSS SD-1: SUPER OverDrive

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance

10 kΩ or greater

Power Supply DC 9 V: Dry battery 6F22 (9 V) type (carbon),

AC Adaptor (PSA-series: optional)

Current Draw 10 mA (DC 9 V)

* Expected battery life under continuous use:

Carbon: 60 hours, Alkaline: 90 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H)inches

Weight 360 g / 13 oz (including battery)

Accessories Owner’s Manual, Leaet (“USING THE UNIT

SAFELY,” “IMPORTANT NOTES,” and “Informa-

tion”), Dry battery/9 V type (6F22)

Options AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

* 5 1 0 0 0 5 5 1 5 5 - 0 2 *

Produkt Specifikationer

Mærke:	Boss
Kategori:	Ikke kategoriseret
Model:	Super Over Drive SD-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss Super Over Drive SD-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Boss Manualer

28 November 2025

27 November 2025

1 Oktober 2025

29 September 2025

Boss SDE-3000EVH Manual

18 Juli 2025

Boss VE-22 Manual

25 Februar 2025

Boss SDE-3 Manual

23 Januar 2025

Boss Distortion DS-1X Manual

1 Januar 2025

Boss RC-505MK2 Manual

1 Januar 2025

Boss GM-800 Manual

1 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025