Broan A80C Manual

Broan Ventilator A80C

Læs gratis den danske manual til Broan A80C (2 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Broan A80C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

OPTION - To mount housing anywhere between ceiling framing: Use

optional Hanger Bar Kit (sold separately from local distributors or website).

Follow mounting instructions included with kit.

1. Remove blower and all packing material

from fan housing.

2. Remove wiring

panel from fan

housing.

3. Attach damper/duct connector to

fan housing.

4. Mount housing to ceiling structure.

ROOF CAP* (with built-in damper)

WALL CAP*

(with built-in

damper)

4-IN. ROUND

ELBOWS*

FAN

HOUSING

Seal gaps

around

housing.

Seal duct joints

with tape.

INSULATION

(Place around and

over fan housing.)

POWER

CABLE *

* Purchase separately.

Keep duct

runs short.

4-IN. ROUND

DUCT*

TABS

5. Connect 4-in. round duct.

ALL INSTALLATIONS

Start here.

IMPORTANT - The ducting from this fan to the outside of the building

has a strong effect on the air flow, noise and energy use of the fan. Use the

shortest, straightest duct routing possible for best performance, and avoid

installing the fan with smaller ducts than recommended. Insulation around

the ducts can reduce energy loss and inhibit mold growth. Fans installed

with existing ducts may not achieve their rated airflow.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer at the address or telephone number

listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock

the service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag, to the service

panel.

3. Installation work and electrical wiring must be done by a qualified person(s)

in accordance with all applicable codes and standards, including fire-rated

construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to prevent

backdrafting. Follow the heating equipment manufacturer’s guideline and

safety standards such as those published by the National Fire Protection

Association (NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Acceptable for use over a tub or shower when connected to a GFCI (Ground

Fault Circuit Interrupter) - protected branch circuit (ceiling installation

only).

8. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or

explosive materials and vapors.

2. This product can be installed in a wall if mounted 8-ft. or more above the

floor.

3. To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

4. Please read specification label on product for further information and

requirements.

CLEANING & MAINTENANCE

For quiet and efficient operation, long life, and attractive appearance -

lower or remove grille and vacuum interior of unit with the dusting brush

attachment.

The motor is permanently lubricated and never needs oiling. If the motor

bearings are making excessive or unusual noises, replace the blower

assembly (includes motor and impeller).

OPERATION

Use an on/off switch or speed control to operate this ventilator. See

“Connect Wiring” for details.

READ AND SAVE THESE INSTRUCTIONS

SERIES FAN

Push connector through

opening from inside of

housing.

Engage tabs and secure

with screw from parts bag.

Make sure bottom of

housing will be flush with

finished ceiling.

For proper location using

½” ceiling material: Bend

out housing tabs to fit

against bottom of structure.

Secure housing through

mounting ears with

appropriate fasteners.

(Some models include

mounting screws.)

If mounting housing to

I-joist, use wood blocking

as shown.

NEW CONSTRUCTION INSTALLATION

HOUSING

TABS

Cooking

Equipment

Floor

COOKING AREA

Do not install above or

inside this area.

45o45o

NOT FOR USE IN

A COOKING AREA.

For Warranty Statement, Service Parts, Technical Support, or to Register your

product, please visit our website or call:

In the United States - Broan.com 800-637-1453 or NuTone.com 888-336-6151

In Canada - Broan.ca or NuTone.ca 877-896-1119

For Retrot Installation - Skip to back page.

Produkt Specifikationer

Mærke:	Broan
Kategori:	Ventilator
Model:	A80C

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan A80C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator Broan Manualer

Broan AE50110DCL Manual

19 Oktober 2025

Broan QTXEG110 Manual

7 August 2025

Broan ZB80L1 Manual

8 Juli 2025

Broan LP510R Manual

7 Juli 2025

Broan L500 Manual

7 Juli 2025

Broan Roomside AR80LWH Manual

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

Soler & Palau FIRE FAN { Manual

4 November 2025

Termozeta Airzeta Millepale TZAZML01 Manual

3 November 2025

Kensington FS18-T1R Manual

3 November 2025

Soler & Palau CRVB-N Manual

1 November 2025

Toshiba F-DSD40XMYW Manual

1 November 2025

Tornado EFS-95SR Manual

1 November 2025

Soler & Palau CTB Manual

1 November 2025

Tornado TWF-16 Manual

1 November 2025

Dimplex DCPF40CPT Manual

1 November 2025

Tornado TWF-18G Manual

1 November 2025