BTI Aqua-Solutions C2400 Manual

BTI Aqua-Solutions Kran C2400

Læs gratis den danske manual til BTI Aqua-Solutions C2400 (4 sider) i kategorien Kran. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om BTI Aqua-Solutions C2400, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
FILTRATION FAUCET INSTALLATION INSTRUCTIONS
ITEM C2100
ITEM C2200
ITEM C2400
ITEM H2100
ITEM H2200
ITEM H2400
ITEM HC2100
ITEM HC2200
ITEM HC2400
SHUT OFF WATER SUPPLY
BEFORE INSTALLATION
Drill 3/4” to 1” in diameter hole in
countertop. Maximum counter
thickness is 2”
O-ring over the mounting hole on
the top of the countertop. Center the
faucet body on the base plate.
If desired, apply a thin bead of silicone
seal under the base plate for added
sealing.
DO NOT USE PLUMBERS’ PUTTY
Place faucet handle in desired position.
Fasten the faucet from under the
countertop, sliding large rubber wash-
er, then metal washer, then smaller
rubber washer, then 5/8” diameter
serrated lock washer on the faucet
stem, and secure with the lock nut so
the faucet does not move/spin.
DO NOT OVER TIGHTEN
COLD ONLY FILTRATION FAUCET W/ FILTRATION SYSTEM
ITEMS: C2100, C2200, C2400
1 2 3
www.btiaquasolutions.com • 7022 S. Revere Parkway Suite 240 • Centennial, CO 80112 • 720.322.0800 (o) 720.322.0801 (f)
9-1/2”
7-1/2”
5-3/8”
3-1/4”
2-1/8”
9-1/2”
7-1/2”
5-3/8”
6-1/2”
2-1/8”
9-11/16”
4”
2-3/4”
2-1/8”
6-1/4”
3-1/4”
4-1/4”
9-11/16”
4”
2-3/4”
2-1/8”
6-1/4”
6-5/8”
9-3/4”
2-1/8”
2-3/4”
4”
6-3/4”
9-3/4”
2-1/8”
5-1/2”
4”
6-3/4”
C2100 / H2100 HC2100 C2200 / H2200 HC2200 C2400 / H2400 HC2400
REV. / /1811 19
TOOLS REQUIRED
ADJUSTABLE WRENCH • DRILL • PLUMBERS’ TAPE
PHILLIPS HEAD SCREWDRIVER
Faucet Stem
Base Plate
Rubber Washer
Metal Washer
Lock Washer
Lock Nut
Tube Insert
Ferrule
Compression Nut
1/4” Water Inlet
Tubing
(supplied
with BTI Filtration
System FL1000)
Rubber Washer
FILTRATION FAUCET INSTALLATION INSTRUCTIONS, page 2 of 4
TIGHTEN SECURELY WITH WRENCH.
COLD ONLY FILTRATION FAUCET W/ FILTRATION SYSTEM
ITEMS: C2100, C2200, C2400
Once a clean flow of water is achieved, check for leaks, ESPECIALLY at the water supply and connection points. If leak(s) are
present, shut off the water supply, repair the leak and re-test the system as previously described.
4
Slide the metal 1/4” compression nut
over the supply tubing (provided with
the filtration system). Next, place the
plastic ferrule (large end first) over
the supply tubing into the compres-
sion nut.
If you are using the BTI Filtration
System ITEM FL1000, you have ample
tubing to connect to the faucet and
still leave 4 -6” of extra tubing before "
the connection point.
5
Place the 1/2” long plastic insert into
the end of the tubing and tighten the
compression nut on the faucet stem.
6
*COMPLETE FILTRATION SYSTEM
INSTALLATION USING INSTALLATION
GUIDE INCLUDED WITH YOUR SPECIFIC
BRAND OF FILTRATION SYSTEM.
Then, open the handle on the filtration
faucet and turn on the water supply.
Allow the water to run for 1-2 minutes
to clear any debris that might be present
in the water line.
7
FILTRATION SYSTEM INSTALLATION WITH BTI HOT/COLD FILTRATION FAUCET AQUA-SOLUTIONS
ITEMS: HC2100, HC2200, HC2400
A
B
C
D
E
F
F
G
(A) FILTRATION FAUCET
(B) BTI FILTRATION SYSTEM-FL1000
(C) LINE/HOSE TO KITCHEN FAUCET
(D) ANGLE SHUT-OFF VALVE (supplied)
(E)
COLD-WATER SUPPLY SHUT-OFF VALVE
(F) 1/4” O.D. TUBING (supplied)
(G) 3/8” / 1/4” ADAPTER (supplied ) w/faucet
Install angle shut-off valve (D) supplied with BTI
Filtration System.
Shut-off cold-water supply (E). Disconnect line/
hose (C) to kitchen faucet from cold-water
supply shut-off valve (E).
Connect angle shut-off valve (D) to cold-water
supply shut-off valve (E). Connect line/hose from
kitchen faucet (C) to angle shut-off valve (D).
Cut the 1/4” O.D. inlet/outlet tubing (supplied) to
the correct lengths, ensuring the cut ends are
square and clean.
Push one end of tubing (F) into angle shut-off
valve (D). Push other end of tubing into
“L-Fitting”, pre-installed in the “inlet” on top
of filter.
Connect 3/8” Female-Side of adapter (G)
(supplied) to braided blue label
cold-water in hose. Push one end of tubing
(F) into 1/4” Push-Fit Side of adapter (G).
Push other end of tubing (F) into “outlet”
connector on top of filter.
To remove a tube, push down on the collet
while pulling on the tube.
Turn on the water supply and check for
leaks. Flush at least one gallon of water
through the system before use.
Write the installation and filter change
dates on the label for future reference.

Produkt Specifikationer

Mærke: BTI Aqua-Solutions
Kategori: Kran
Model: C2400

Har du brug for hjælp?

Hvis du har brug for hjælp til BTI Aqua-Solutions C2400 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Kran BTI Aqua-Solutions Manualer

BTI Aqua-Solutions

BTI Aqua-Solutions C2400 Manual

31 Marts 2025
BTI Aqua-Solutions

BTI Aqua-Solutions C2200 Manual

31 Marts 2025

Kran Manualer

Nyeste Kran Manualer

Rohl

Rohl Miscelo MI09D3GQMB Manual

7 April 2025
Oliveri

Oliveri KE2030 Manual

7 April 2025
Sussex

Sussex VSM-04 Manual

7 April 2025
Shaws

Shaws AUSH-4341 Manual

7 April 2025
Shaws

Shaws AUSH-4751 Manual

7 April 2025
Sussex

Sussex CBM-54 Manual

7 April 2025
Sussex

Sussex VSMQ-60 Manual

7 April 2025
Shaws

Shaws AUSH-4756 Manual

7 April 2025
Shaws

Shaws AUSH-4861 Manual

7 April 2025
Oliveri

Oliveri MT0039 Manual

7 April 2025