Bulgin PX0739/S Manual

Bulgin Ikke kategoriseret PX0739/S

Læs gratis den danske manual til Bulgin PX0739/S (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Bulgin PX0739/S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Buccaneer connectors are available in 2, 3, 4, 6, 7, 9, 12 or 25 pin and BNC

coaxial versions (50/75Ω).

It is important that these instructions are fully complied with to ensure the

product is completely watertight and electrically safe -

IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN.

Always wire the socket insert to supply, and the plug insert to appliance.

Plug/socket inserts can be fitted into any style of main body to give correct

plug/socket combination for your application.

Use smooth circular cable only (6-8mm dia). Other cable glands are available to

suit different cable diameters, please enquire.

ASSEMBLY/WIRING INSTRUCTIONS

1To remove plug or socket inserts for wiring, use cap assembly tool to

unscrew locking ring.

2As appropriate to main body type, thread cable through component parts

as shown in the illustrations.

3Strip insulation from cable as shown in Flex Mounting diagram.

42 to 7 pole inserts:

Insert bare wire ends into terminals on plug/socket insert and fully tighten

screws.

Note: If connector is to be used on mains voltage ensure that wires are

connected as shown below.

9 pole inserts:

Pins and sockets are supplied loose for pre-crimping. Crimping tools

(including hand versions) and a contact extraction device are available.

Please enquire.

12 and 25 pole inserts:

Pins and sockets are supplied loose for pre-crimping and pre-soldering.

Crimping tools (including hand version) and a contact extraction device are

available. Please enquire.

5After connecting wires, draw cable back until plug/socket insert is correctly

seated in D shaped location in the main body. Screw home locking ring

using cap assembly tool.

6For cable mounted units, slide gland cage and gland down cable and into

main body then screw gland nut fully home. It is essential to ensure that

the gland nut is fully tightened to ensure cable is securely sealed and

clamped. For panel, bulkhead and flange units correctly seat sealing

washer and main body onto mounting surface and screw down using rear

nut or screw/bolts with seals. Ensure seals and glands are kept clean.

Locking cap secures plug to socket.

Note:

To ensure that the correct sealing properties of the connector are achieved it is

imperative that all ‘O’ rings are correctly located and seated before assembly.

Please refer to the exploded diagrams for the locations of these seals.

Standard Buccaneer Waterproof Electrical Cable Connector

FLEX MOUNTING

FRONT OF PANEL MOUNTING

REAR OF PANEL MOUNTING

LOW PROFILE FLANGE MOUNTING

BULKHEAD/SURFACE MOUNTING

Mains Wire Connections

Important - connect

wires Brown to terminal

L, Blue to terminal N

and Green/Yellow to

terminal E

For your protection all mains (250V)

equipment used out of doors, in damp or

wet conditions should be supplied from a

correctly fused source and protected by an

approved R.C.D. Eg: BS7071, BS7288,

BS4293, BSEN61008 or BSIEC1008.

IF IN DOUBT SEEK ADVICE

IMPORTANT SAFETY NOTICE

FLEX MOUNTING IN-LINE

Part No: 13158, issue 8

Wiring and Assembly Instructions

Buccaneer®

IP68 & IP69 Waterproof Connectors

Wiring and Assembly Instructions

PANEL CUT-OUTS

FRONT PANEL MOUNTING REAR PANEL MOUNTING

BULKHEAD/SURFACE MOUNTING

SEALING CAP/ASSEMBLY TOOL

Assembly Instructions Buccaneer R.F. Insert (BNC Compatible)

For use with cables:

50Ω - URM 76, URM 43, RG58c/u.

75Ω - URM 70.

Crimp Tool - Hex Cavities,

Centre Contact 1.69 A/F (B.S. ‘W’/ERMA XA.)

Braid 6.48 A/F (B.S. ‘E’/ERMA XH.)

1 Flex Mount

Fit gland nut, washer, gland & main body loosely over cable, followed by BNC

plug/jack metal body.

Chassis/Bulkhead

Fit main body to chassis/bulkhead, ensuring sealing washer(s) are in position.

Then assemble BNC plug/jack body to cable.

2 Crimp centre contact onto cable centre conductor (butting to cable inner

insulator).

3Slide knurled ferrule over contact & cable inner insulator & under cable braid.

4Snap-Fit insulator over centre contact (support insulator with assembly

mandrel, or against hard surface).

5Push body over assembly, pressing insulator, until ferrule bottoms in body.

(SA3155 assembly mandrel is available to aid assembly if required).

6Crimp body to secure cable braid.

7Lock BNC body flange into main body using locking ring. Ensure correct

alignment of flat.

8 At cable entry, seat gland & washer, tighten gland nut to seal (for

flex mount).

CABLE TRIM & PIECE PARTS

FLEX MOUNTING

IN-LINE CO-AXIAL CABLE

CONNECTOR

FLEX MOUNTING

C O-AXIAL CABLE

C ONNECTOR

bulgin

a brand of Elektron Technology

bulgin.com

Produkt Specifikationer

Mærke:	Bulgin
Kategori:	Ikke kategoriseret
Model:	PX0739/S

Har du brug for hjælp?

Hvis du har brug for hjælp til Bulgin PX0739/S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Bulgin Manualer

Bulgin PX0587/SE Manual

4 December 2024

Bulgin PX0588 Manual

4 December 2024

Bulgin PX0587 Manual

4 December 2024

Bulgin PX0739/S Manual

4 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Miele WTV 417 Manual

10 Oktober 2025

Miele EBA 7747 Manual

10 Oktober 2025

Panasonic MX-HG4401 Manual

10 Oktober 2025

Fresh 'n Rebel Selfie Stick Manual

10 Oktober 2025

TOA VX-3308WM Manual

10 Oktober 2025

Teka EWH 100 DHH Manual

10 Oktober 2025

Xerox App Gallery Manual

10 Oktober 2025

Miele WTV 511 Manual

10 Oktober 2025

Miele WTV 601 Manual

10 Oktober 2025

Miele GaLa-S Manual

10 Oktober 2025