Byron SX35 Manual

Byron Dørklokke SX35

Læs gratis den danske manual til Byron SX35 (1 sider) i kategorien Dørklokke. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Byron SX35, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

SX Range Bell Push SX-35

Byron No.SX35 Size: A4 Date: 11 Oct 2007

3. Feed the wire via the hole on the back of the Push Button and connect the wire to the terminal

positions A & B as marked.

4. Snap the back cover of Push Button back on, then it is ready to use.

Important: Do not connect the Wireless Push Button unit with any Lighted Bell Push.

Important

1. Do not mount either unit close to fireplace or expose to high temperatures.

2. Do not expose the Door Chime unit to direct sunlight or moisture

3. Always use alkaline battery. Please dispose of old, defective batteries in an environmentally

friendly manner in accordance with the relevant legislation.

4. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.

5. The unit should not be exposed to dripping or splashing and no objects filled with liquids, such

as vases, should be placed on the unit.

6. Replace only with the same or equivalent type of battery that is recommended by the CAUTION:

manufacturer.

7. Make sure batteries are installed correctly as per the internal marking.CAUTION:

8. Danger of explosion if battery is incorrectly installed or replaced.CAUTION:

9. IMPORTANT: There are no serviceable parts in the units, do not attempt to repair it.

User Hints

If the door chime unit does not sound, please check the following:

a) Flat batteries in either Push Button or Door Chime units - change the batteries.

b) Wrong battery polarity in either Push Button or Door Chime units - re-insert the batteries.

c) Push Button or Door Chime units are not on the same operation codes - re-set the code (see

digital code set up).

d) Units are out of range - Operate the Chime unit within the operation range.

Specification

Operating Temperature: -10C – +40C

Selectable Tone: Total Eight (8) melodies available

Selectable Digital Code: Total two hundred fifty six (256) possible digital codes

“Type R2 Device - device where the sound output is created by the initial operation of the

control and where the period of sound output continues for the designed duration

irrespective of condition of the control.”

433MHz

R&TTE

APPROVED

CH Byron Electrical United Kingdom. www.chbyron.com

CH Byron Electrical Ltd

Byron House

34 Sherwood Rd, Astonfield

Bromsgrove, B60 3DR

Tel: 0845 2301231

e: support@chbyron.com

w: www.chbyron.com

A B CA B C

Push Button

• Open up the push button by pushing in the tab at the

bottom of the push with a small flat screwdriver.

• Remove the isolation strip from the battery

compartment then it is ready to use.

• When replacing the battery, ensure the battery

polarity matches the internal markings (“+” facing

upwards), then press the battery down so that it is

sitting firmly in its compartment.

CR2032 3V

Lithium

Battery

Remove

Isolation

Strip

1 2

Melody Selection

Press the melody selector once to select a melody as

your Byron SX Range door chime sound.

Digital Code Set Up

• Press the Push Button once, a new operation code is

generated randomly and sent to the Door Chime unit.

• The Door Chime will sound to indicate that a new

operation code is registered and memorised.

Push Button Installation

• Using the holes on the back of push button as a

template, mark the fixing position for the unit.

• Drill holes and fit wall plugs and secure the push

button unit to the wall with screws.

• Do not mount it on any metal surface or UPVC door

frame.

ABCABC

A B CA B C

Melody Selector

Wiring Installation

The Push Button can be used as converter to change your existing Wired Bell Push to wire free.

1. Connect your Wired Bell Push cable to the built-in terminal positions A & C of Wireless Bell Push.

2. Your Wired Bell Push with Wireless Push Button is ready to use.

In case a Transformer (A/C 8V) is used to power the Wired Bell Push and Wired Door Chime.

1. Remove the back of case by pushing in the tab on the bottom with a small, flat screwdriver.

2. Disconnect the wire that connected with Wired Door Chime.

Feed the wire via the hole on the back of the Push Button and connect the wire to the terminal positions A & B as marked.

4. Snap the back cover of Push Button back on, then it is ready to use.

Important: Do not connect the Wireless Push Button unit with any Lighted Bell Push.

WIRED

CHIME

(Transformer

operation)

WIRED

CHIME

(Transformer

operation)

A B CA B C

Important: This Bell Push is designed to work with Byron SX Range Door Chime only

Push Button unit

Power: 1 x 3volt Lithium battery (CR2032 - included)

Melody Selection

Press the melody selector once to select a melody as your Byron SX Range door chime

sound.

Digital Code Set Up - When work with Byron SX Range Door Chime

The Door Chime kit is equipped with an advanced random and self-learning operation

coding ability therefore no setting is needed. Read the following instructions before use.

1. First time operation:

After battery installation on the Push Button and Door Chime units, press the Push Button once

and it will generate a new operation code randomly and send a wireless signal to the Door Chime

unit. The door chime will sound to indicate that a new operation code is registered and

memorised.

2. Interference from a similar unit operating nearby:

a) Simply remove the batteries from the Push Button and Door Chime units and rest for 10

seconds, this will erase the memory.

b) Insert the batteries into the Push Button and Door Chime units, the door chime unit will give

2-beeps to indicate that it is ready for the new code registration. Press the Push Button once,

it will generate a new operation code randomly and send a wireless signal to the Door Chime

and it will sound to indicate that a new operation code is registered and memorised.

3. Front and back door Bell Push operation:

a) Remove the batteries from the Push Buttons (Front & Back Door) and Door Chime units and

rest for 10 seconds, this will erase the memory.

b) Insert the batteries into the Push Buttons and Door Chime units, the door chime unit will give

2-beeps to indicate that it is ready for the new code registration.

c) Press the front door Push Button once, it will generate a new operation code randomly and

send a wireless signal to the door chime unit and it will sound to indicate that a new operation

code is registered and memorised.

d) After, (within 2 minutes) press the back door Push Button once, it will generate a new

operation code randomly and send a wireless signal to the door chime unit and it will sound to

indicate that a new operation code is registered and memorised. The door chime unit has the

ability to memorise both operation codes.

e) Test to ensure correct operation before final installation.

Wiring Installation

The Push Button can be used as converter to change your existing Wired Bell Push to wire free.

1. Connect your Wired Bell Push cable to the built-in terminal positions A & C of Wireless Bell Push.

2. Your Wired Bell Push with Wireless Push Button is ready to use.

In case a Transformer (A/C 8V) is used to power the Wired Bell Push and Wired Door Chime.

1. Remove the back of case by pushing in the tab on the bottom with a small, flat screwdriver.

2. Disconnect the wire that connected with Wired Door Chime.

Produkt Specifikationer

Mærke:	Byron
Kategori:	Dørklokke
Model:	SX35

Har du brug for hjælp?

Hvis du har brug for hjælp til Byron SX35 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Dørklokke Byron Manualer

Byron DBY-23512 Manual

4 Oktober 2024

Byron B432E Manual

4 Oktober 2024

Byron 10.015.46 Manual

1 Oktober 2024

Byron DB304 Manual

23 September 2024

Byron DBY-24112 Manual

23 September 2024

Byron BY102 Manual

22 September 2024

Byron B411E Manual

22 September 2024

Byron 10.020.40 Manual

21 September 2024

Byron 10.020.06 Manual

10 September 2024

Byron 7720 Manual

10 September 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Avidsen 102507 Manual

17 Juni 2025

Eura WDP-42A3 Manual

15 Juni 2025

ORNO OR-DOM-YR-934 Manual

15 Juni 2025

ORNO OR-DOM-BA-936 Manual

15 Juni 2025

ORNO OR-DOM-BA-935 Manual

15 Juni 2025

ORNO OR-DB-KD-178 Manual

15 Juni 2025

ORNO OR-DP-MR-176 Manual

15 Juni 2025

ORNO OR-DB-KD-177 Manual

14 Juni 2025

Franke FTC 912 XS LED1 Manual

9 April 2025

Philips HSP5310 Manual

11 Marts 2025