CAD Audio U7 Manual

CAD Audio Mikrofon U7

Læs gratis den danske manual til CAD Audio U7 (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 18 anmeldelser. Har du et spørgsmål om CAD Audio U7, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

U7 USB Tabletop Recording

Microphone

Before using the U7 in your favorite audio or communications application

you must conﬁ rm that the computer’s operating system recognizes the U7

microphone.

Windows XP recognition instructions

1. Plug the U7 into the USB port on the computer.

(When using a USB hub, check with the hub manufacturer to be sure

the hub supports a device such as a microphone. Plug the microphone

directly into the computer’s powered USB port for optimal performance.)

2. Allow 30 to 60 seconds for the system software to recognize the U7.

(A series of bubbles will appear by the Windows toolbar to notify you

of a new device.)

3. In the Start Menu, select Control Panel.

4. Select “Sounds, Speech, and Audio Devices”.

5. Select “Sounds and Audio Devices”.

6. Select the “Audio” tab. Conﬁ rm that under the “Sound recording”

section the “C-Media USB Audio Device” is selected. (The “Sound

playback” should remain your usual sound output device).

7. Select the “Volume” tab under the Sound recording heading and

select “Advanced Controls” in the Options menu of this window.

8. Click the “Advanced” button to open the “Advanced Controls for

Wave In” window. Depending upon your system, you might have the

option of selecting “1 AGC” or “Mic boost”. Checking this option will

signiﬁ cantly increase the sensitivity of the microphone. Use this for

recording softer sounds. If you experience distortion when recording

louder sounds, try unchecking this option.

(Default playback device)

9. Launch your audio recording software.

10. Position the U7 approximately 4 to 6 inches from the sound source for

best results.

11. Locate the preferences in your audio program and select the “C-Media

USB Audio Device”. Adjust the input level in this program so that the

audio signal is not distorted.

12. Enjoy your CAD U7 USB Tabletop Recording Microphone.

Mac OSX recognition instructions

1. Plug the U7 into the USB port on the computer.

(When using a USB hub, check with the hub manufacturer to be sure

the hub supports a device such as a microphone. Plug the U7 directly

into the computer’s powered USB port for optimal performance.)

2. Allow 30 to 60 seconds for the system software to recognize the U7.

3. Go to the Apple Menu and locate “System Preferences”.

4. Under “Hardware” click on the “Sound” icon.

5. Click on the “Input” button and choose the “C-Media USB Audio Device”.

6. or the Click on the “Output” button and choose the internal speakers

output speakers of your choice. (The “Sound playback” should remain

your usual sound output device).

7. Position the U7 4 to 6 inches away from your source (your mouth or

music instrument).

8. Test the U7 by speaking or playing into the microphone.

9. You will see activity in the “Input Level” meter.

10. As you are speaking or playing adjust the “Input Volume” slider. Take

care not to allow the signal to go beyond the meter, if the meter is

fully illuminated the sound can become distorted. The meter should be

illuminated 3/4ths of the way to obtain the best sound quality.

11. Close the System Preferences window to complete the settings.

12. Launch your audio recording software.

13. Position the U7 approximately 4 to 6 inches from the sound source for

best results.

14. Locate the Preferences in your audio program and select the “C-Media

USB Audio Device”. Adjust the input level in this program so that the

audio signal is strong but not distorted.

15. Enjoy your CAD U7 USB Tabletop Recording Microphone.

CAD Professional Microphones

6573 Cochran Rd., Bldg. Solon, OH 44139I

800-762-9266 www.cadmics.com

NOTE: This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment gener-

ates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Two-Year Limited Warranty

CAD Professional Microphones hereby warrants that this product will be free of defects in material and workmanship for a

period of two years from the date of purchase. In the unlikely event that a defect occurs CAD will, at its option, either repair

or replace with a new unit of equal or greater value. Retain proof of purchase to validate the purchase date and return it with

any warranty claim.

Return warranty claims carefully packed, insured and prepaid to the Service Department at the address listed below.

This warranty excludes exterior ﬁ nish or appearance, damage from abuse, misuse of the product, use contrary to CAD’s

instructions or unauthorized repair. All implied warranties, merchantability, or ﬁ tness for a particular purpose is hereby

disclaimed and CAD hereby disclaims liability for incidental, special or consequential damages resulting from the use or

unavailability of this product.

This warranty gives you speciﬁ c legal rights and you may have other rights that vary from state to state. Some states do not

allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts,

so the above exclusions and limitations may not apply to you.

Note: No other warranty, written or oral is authorized by CAD Professional Microphones.

Shipping Instructions

Please call our customer service department at 440-349-4900 for a pre-approved return authorization number. Carefully

repack the unit and return it to: CAD Professional Microphones, 6573 Cochran Road, Building , Solon, Ohio 44139. I

RETURNS WITHOUT A PRE-APPROVED RETURN AUTHORIZATION NUMBER WILL BE REFUSED.

If outside the United States, contact your local dealer or distributor for warranty details.

Produkt Specifikationer

Mærke:	CAD Audio
Kategori:	Mikrofon
Model:	U7

Har du brug for hjælp?

Hvis du har brug for hjælp til CAD Audio U7 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon CAD Audio Manualer

CAD Audio GXLD2QM Manual

11 September 2025

CAD Audio GXLD2 Manual

11 September 2025

CAD Audio WX200 Manual

11 September 2025

CAD Audio M179 Manual

13 August 2025

CAD Audio WX1610 Manual

3 September 2024

CAD Audio TX1000BP Manual

3 September 2024

CAD Audio WX1000BP Manual

3 September 2024

CAD Audio D29 Manual

26 August 2024

CAD Audio U7 Manual

26 August 2024

CAD Audio U1 Manual

26 August 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Synco WAir P1S Manual

11 September 2025

Synco MIC-D1 Manual

11 September 2025

Synco WAir P2S Manual

11 September 2025

Adam Hall 5730 Manual

11 September 2025

Point Source Audio Series8 CR-8S Manual

10 September 2025

Musicmate B-13 Manual

10 September 2025

Defender Space GMC 450 Manual

10 September 2025

Musicmate S-105N ClearTone Manual

10 September 2025

I.safe Mobile IS-RSM3A.1 Manual

10 September 2025

Krux Esper 1000 Manual

10 September 2025