Casio Classic AMWS850D-1AV Manual

Casio Ur Classic AMWS850D-1AV

Læs gratis den danske manual til Casio Classic AMWS850D-1AV (6 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Casio Classic AMWS850D-1AV, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Operation Guide 5208

MO1106-EA

E-1

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a built-in battery. Leaving or using the watch

where it is not exposed to light causes the battery to run

down. Make sure the watch is exposed to light as much as

possible.

•When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

•You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced significantly if

the face is only partially covered.

Bright Light

Solar cell

E-2

Battery charges in the light. Battery discharges in the dark.

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

•The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some watch

functions being disabled. If the battery goes dead, you will have to re-configure

watch settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

E-3

•The actual level at which some functions are disabled depends on the watch model.

•Be sure to read “Power Supply” (page E-33) for important information you

need to know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

•See “Power Saving Function” (page E-46) for more information.

E-4

About This Manual

•Depending on the model of your watch, display text

appears either as dark figures on a light background, or

light figures on a dark background. All sample displays

in this manual are shown using dark figures on a light

background.

•Button operations are indicated using the letters shown

in the illustration.

•Each section of this manual provides you with the

information you need to perform operations in each

mode. Fur ther details and technical information can be

found in the “Reference” section.

E-5

Contents

General Guide ......................................................................................................... E-8

Timekeeping .......................................................................................................... E-10

World Time ............................................................................................................. E-17

Alarms .................................................................................................................... E-20

Countdown Timer .................................................................................................. E-24

Stopwatch .............................................................................................................. E-29

Illumination ............................................................................................................ E-31

Power Supply ........................................................................................................ E-33

Adjusting Home Positions ................................................................................... E-42

Reference .............................................................................................................. E-44

Specifications ....................................................................................................... E-50

E-6

Procedure Lookup

The following is a handy reference list of all the operational procedures contained in

this manual.

To set the current digital time and date .............................................................. E-11

To change the Daylight Saving Time (summer time) setting ............................ E-15

To view the time in another city ........................................................................... E-18

To toggle a city code time between Standard Time

and Daylight Saving Time ............................................................................... E-18

To swap your Home City and World Time City ................................................... E-19

To set an alarm time ............................................................................................. E-21

To turn an alarm on and off .................................................................................. E-23

To turn the Hourly Time Signal on and off .......................................................... E-23

E-7

To configure the countdown timer ...................................................................... E-25

To use the countdown timer ................................................................................ E-27

To measure times with the stopwatch ................................................................ E-30

To illuminate the display ...................................................................................... E-31

To specify the illumination duration ................................................................... E-32

To check the current battery level ....................................................................... E-35

To adjust home positions ..................................................................................... E-42

To turn the button operation tone on and off ..................................................... E-45

To recover from the sleep state ........................................................................... E-47

E-8

Timekeeping Mode

▲

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press B to illuminate

the face of the watch.

Battery Level Indicator

▲

E-9

Stopwatch Mode Countdown Timer Mode

Alarm Mode

▲

World Time Mode

▲

C C

▲

Operation Guide 5208

E-10

•All of the operations in this section are performed in the Timekeeping Mode, which

you can enter by pressing (page E-8).C

Timekeeping

Use the Timekeeping Mode to set and view the current time and date.

•When setting the time, you can also configure settings for the 12/24-hour format.

•Each press of D cycles the digital display in the sequence shown below.

Day

Day of week

▲

PM indicator

Hour : Minute

SecondSecond Second

Month

▲

E-11

City code

Setting the Digital Time and Date

Make sure you select your Home City code before you change the current time and

date settings. World Time Mode times are all displayed in accordance with the

Timekeeping Mode settings. Because of this, World Time Mode times will not be

correct if you do not select the proper Home City code before setting the time and

date in the Timekeeping Mode.

To set the current digital time and date

1. In the Timekeeping Mode, hold down A for about two

seconds, until “ADJ” appears on the display.

•Your current Home City code will be flashing on the

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

E-12

3. While the setting you want to change is flashing, use D and B to change it as

explained below.

Screen: To do this:

Change the city code

Toggle between Daylight Saving Time

(ON) and Standard Time (OFF).

Toggle between 12-hour ( ) and12H

24-hour ( ) timekeeping24H

Reset the seconds to 00

Do this:

Press D (east) and B (west).

Press D.

City Code

Language Illumination

Duration Day Month Ye a r

DST 12/24-Hour

Format Seconds Hour Minutes

Button Operation

To ne

E-13

To do this:

Change the hour or minutes

Change the year

Change the month or day

Toggle the button operation tone

between (on) and (off)

Toggle the illumination duration between

LT1 (approximately 1.5 seconds) and

LT3 (approximately 3 seconds).

Change the day of the week language

ENG: English : PortuguesePOR

ESP: Spanish : FrenchFRA

DEU: German ITA : Italian

Screen: Do this:

Use D (+) and B (–).

Press D.

Use D (+) and B (–).

•See “City Code Table” at the back of this manual for a complete list of available

city codes.

E-14

4. Press A to exit the setting screen.

•The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

12-hour and 24-hour timekeeping

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears for times in the

range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

E-15

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A for about two seconds, until “ADJ” appears

on the display.

•Your current Home City code will be flashing on the screen.

2. Press C once to display the DST setting screen.

3. Press D to toggle between Daylight Saving Time ( displayed) and StandardON

Time (OFF displayed).

4. When the setting you want is selected, press A to exit the setting screen.

•The DST indicator appears on the display to indicate that Daylight Saving Time is

turned on.

E-16

Analog Timekeeping

The analog time of this watch is synchronized with the digital time. The analog time

setting is adjusted automatically whenever you change the digital time.

Note

•The hands for the analog timepiece move to adjust to a new setting whenever any of

the following occurs.

When you change the digital time setting

When you change the Home City code and/or DST setting

•If the analog time does not match the digital time for any reason, use the procedure

described under “To adjust home positions” (page E-42) to match the analog setting

to the digital setting.

•Whenever you need to adjust both the digital and the analog time settings, make

sure you adjust the digital setting first.

•Depending on how much the hands have to move in order to synchronize to the

digital time, it may take some time before they stop moving.

E-17

World Time

The World Time Mode digitally displays the current time in

48 cities (31 time zones) around the world.

•If the current time shown for a city is wrong, check your

Home City time settings and make the necessary

changes (page E-11).

•After you press C to enter the World Time Mode, your

currently selected World Time City code will appear on

the digital display for about two seconds. After that, the

current time in that city will appear.

•All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C

(page E-9).

City code

Current time in

selected city

E-18

To view the time in another city

If you press D while in the World Time Mode, your currently selected World Time City

code will appear on the digital display for about two seconds. After that, the current

time in that city will appear. Pressing D again while the World Time City code is

displayed will scroll to the next city code.

•For full information on city codes, see the “City Code Table” at the back of this

manual.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city code

(time zone) whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down A to toggle Daylight Saving Time (DST

indicator displayed) and Standard Time (DST indicator

not displayed).

• The DST indicator will appear on the display whenever

you display a city code for which Daylight Saving Time is

turned on.

DST indicator

E-19

• Note that the DST/Standard Time setting affects only the currently displayed city

code. Other city codes are not affected.

Swapping your Home City and World Time City

You can use the procedure below to swap your Home City and World Time City. This

changes your Home City to your World Time City, and your World Time City to your

Home City. This capability can come in handy when you frequently travel between two

cities in different time zones.

To swap your Home City and World Time City

1. In the World Time Mode, use D to select the World Time City you want.

2. Hold down A and B until the watch beeps.

• This will make the World Time City you selected in step 1 your Home City, and cause

the hour and minute hands to move to the current time in that city. At the same time,

it will change the Home City you had selected prior to step 2 your World Time City.

• After swapping the Home City and World Time City, the watch stays in the World

Time Mode with the city that was selected as the Home City prior to step 2 now

displayed as the World Time City.

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	Classic AMWS850D-1AV
Vandfast:	Ja
Kalender:	Ja
Stopur:	Ja
Urtype:	Armbåndsur
Alarmfunktion:	Ja
Mekanismetype:	Quartz (solar)
Se opkaldstype:	LED-skive
Vandbestandig dybde:	50 m
Husets farve:	Grå
Stopurets nøjagtighed:	100 sek./side
Verdenstid funktkon:	Ja