CDA KC42WH Manual

CDA Vask KC42WH

Læs gratis den danske manual til CDA KC42WH (1 sider) i kategorien Vask. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11 anmeldelser. Har du et spørgsmål om CDA KC42WH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

KC41 and KC42 Fitting Instructions

FAILURE TO FOLLOW THESE INSTRUCTIONS CAN LEAD TO PREMATURE PRODUCT FAILURE.

The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or

installation of this product. Please note that CDA reserve the right to invalidate the guarantee

supplied with this product following incorrect installation or misuse of the appliance or use in a

commercial environment.

Over Mounting

1. Place the paper template provided carefully into the correct position on the worktop.

2. Cut along the over mount line until the central section of the worktop comes out.

3. Use clear silicone to seal the cut that has been made; liberally spread the silicone onto the

area of the worktop directly adjacent to the hole you have made to the width of the sink rim

that it will come into contact with.

4. Repeat step 3 on the under side of the sink rim itself on the surface that will come into

contact with the worktop.

5. Carefully position so that you avoid unnecessary readjustment of the sink at the moment of

contact.

6. Press down firmly and hold in position for at least 5 minutes applying an even pressure.

7. Ensure the sink is fully sealed and the joint is waterproof by squeezing residual silicone out

from along the line of the joint.

8. Do not use the sink for at least 24 hours once fitted.

9. After 24 hours check to ensure the seal is waterproof.

Under Mounting

1. Place the paper template provided carefully into the correct position on the worktop.

2. Cut along the under mount line until the central section of the worktop comes out.

3. Finish the worktop cut out edge to the desired standard.

4. Turn the worktop upside down on a flat, stable surface. Note this will need to be left in

position for 24 hours.

5. Spread clear silicone liberally on the glazed surface on the rim of the sink ensuring no areas

are left uncovered.

6. Spread clear silicone liberally on the underside of the worktop to the corresponding area

where the rim of the sink will be in contact.

7. Press the sink down into the required position firmly for at least 5 minutes applying even

pressure. Position a weight on the sink to keep it in place.

8. Ensure the sink is fully sealed and the joint is waterproof by squeezing residual silicone out

from along the line of the joint.

9. Do not use the sink for at least 24 hours.

10. 3 metal brackets are provided which should be fixed along the front edge and one on each

side; the edge of the bracket overlaps the sink rim and the other edge fixes to the worktop. If

a stone/granite worktop is being used wooden blocks can be used to affix the clips to secure

the sink; these should be fixed with an epoxy-type adhesive (follow manufacturers’

instructions for Epoxy adhesive use).

Produkt Specifikationer

Mærke:	CDA
Kategori:	Vask
Model:	KC42WH

Har du brug for hjælp?

Hvis du har brug for hjælp til CDA KC42WH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vask CDA Manualer

20 August 2024

16 August 2024

15 August 2024

14 August 2024

14 August 2024

14 August 2024

14 August 2024

14 August 2024

14 August 2024

13 August 2024

Vask Manualer

Nyeste Vask Manualer

Sani-Lav ESB2-607L Manual

3 Marts 2025

Oliveri FL122 Manual

3 Marts 2025

BLANCO ANDANO 340-U Manual

1 Januar 2025

Hendi 970522 Manual

30 December 2025

Blaupunkt Tesino STG5600CEA Manual

30 December 2025

Deante ZQE N10B Manual

28 December 2024

Deante ZZQZA2513 Manual

28 December 2024

Fulgor Milano P1B 7545 Q F-SF Manual

28 December 2024

Caple Zero 35 Manual

27 December 2024

Caple Zero 150R Manual

27 December 2024