CDA TL1CH Manual

CDA Vandhane TL1CH

Læs gratis den danske manual til CDA TL1CH (2 sider) i kategorien Vandhane. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om CDA TL1CH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

For Service & Technical Support Call 01949 862012

TL1 - Lumina single lever

2 Year warranty:

In the unlikely event that you should experience any defect in the materials or workmanship of your new mixer within Two years of purchase,

the purchaser’s sole remedy shall be the replacement (at the manufacturer’s discretion) of all or any part of the product that is defective. All

working parts and valves are guaranteed for a period of TWO years from purchase. Decorative surface finishes, electrical parts and O-rings

are guaranteed for ONE year from the date of ning care has been observed. This is provi purchase provided that our advice concer ded that

the mixer has been used for normal domestic purposes in the UK and that the care, installation and maintenance instructions have been

observed. The warranty extends to the original purchaser only. You should retain a copy of your dated invoice as proof of purchase to

validate any claims under this guarantee.

Care Instructions for your Kitchen Sink Mixer:

To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean, soft damp cloth. A solution of warm water and

a mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly and wiped dry. Any other cleaning action will

invalidate your warranty. If the tap has a diffuser it should be cleaned periodically.

Abrasive cleaners, scouring cleaners and acidic cleaners under any circumstances. Avoid contact with all solvents must not be used

(including chlorinated solvents, ketones or acetones as these may result in surface deterioration or etching). Also avoid contact with any

harsh household chemicals such as oven cleaners, drain cleaners, rust removers, paint strippers and toilet bowl cleaners, bar keepers friend

or Brasso.

Important Technical Data:

Minimum operating pressure 1.25 bar Maximum hot water temperature 70°C*

Maximum operating pressure 5.5 bar* Recommended hot water temperature 46°C

Power consumption 2.7W (max) DC inputs: 9V – 300mA (max)

Supplied transformer: linear, 200 V AC 50Hz 500 mA

*If these temperatures or pressures are exceeded, even for short periods, damage can result.

CDA taps are either WRAS approved or manufactured in accordance with recognised European standards. Please ensure that your

Kitchen mixer is fitted in accordance with Local Water Byelaws.

These installation guidelines have been prepared for your direction and you must exercise due care at all times. We do not accept

responsibility for problems that may occur through improper installation. Whilst assembling the tap take care not to accidentally loosen any

screwed assemblies.

Installation Preparation:

Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any remaining solder,

swarf or impurities from your system. Failure to carry out this simple procedure could cause problems or damage to the workings of the

mixertap.

We strongly recommend installing particle filter strainers and isolation valves to both the hot and cold feed pipes in an accessible position.

This will help to prevent premature failure of the valves and ease any future maintenance.

All parts should be removed from their packaging and inspected for any transport damage prior to installation.

Shut off your water heating system and ensure that your mains stopcock is closed. Open the lowest hot and cold taps in the house and

allow the water to run until the cold-water storage tank and pipes are fully empty. Please note, the hot water storage cylinder (if applicable)

will always remain full.

This mixertap requires a 35mm∅ tap hole, if replacing an existing tap, remove the tap & clean the end of the feed pipes using wire wool the

tap hole area should be free from dirt and sealant.

Loosely position the tap and tail pipes to check if any alteration to the existing pipework is required, if this is the case do this now.

Installation:

1. Pass the upper seal (B) over all wires and pipes onto the base of the tap (A).

2. Pass the threaded section of the mixertap base (A), all wires and pipes through the taphole.

3. Pass the lower washer (E), metal washer (F), and white triangular stabiliser (G) (if fitting to a stainless steel sink) over

all wires, pipes and the threaded section of the mixertap base (A).

4. Pass the ﬁxing nut (H) over all wires and pipes onto the threaded section base of the tap (A). With the tap correctly

located tighten the fixing nut fully.

5. Screw the hot flexible tail pipe (I) into the hot inlet pipe (C). note hot inlet pipe is tagged with [c].

6. Screw the cold ﬂexible tail pipe (O) into the cold inlet pipe (D).

7. Connect the hot & cold flexible tail pipes (I&O) to the water supplies using ½” BSPx15mm compression fittings.

8. Screw the brass sensor (L) to the mixed water out flexible pipe (J), use the rubber washer (K) between the parts to

ensure a water tight seal.

9. Screw the mixed water in flexible pipe (N) to the brass temperature sensor (L) use the rubber washer (M) between the

parts to ensure a water tight seal.

10. Connect the input / output wires (BB,CC & DD) to the control box as shown, note the control box and wire tags are

colour coded in pairs. Important: Do not force the connectors incorrectly into the sockets and check the layout of the

connections now.

11. Plug the transformer into a mains outlet; IMPORTANT: ensure the transformer is set to 9V.

12. Connect the power lead to the control box (P), secure the control box using a cable tie or double sided foam tape.

Note: Above 45°C the tap will light fully red, below 20°C the tap will light fully blue, in between these temperatures the light

will be purple. The light will only activate at a flow rate above 1 litre / minute.

Key: Description: Qty

A Mixertap body 1

B Upper seal 1

C Hot water inlet pipe 1

D Cold water inlet pipe 1

E Lower washer 1

F Metal washer 1

G White triangular stabilizer

(use only if installing tap to

stainless steel sink) 1

H Fixing nut 1

I Hot flexible tail pipe 1

J Mixed water in flexible pipe 1

K Rubber washer 1

L Brass sensor 1

M Rubber washer 1

N Mixed water out flexible pipe 1

O Cold flexible tail pipe 1

Mains Transformer 1

BB black wire, yellow tag

CC Grey wire, red tag

DD Black wire, green tag

After installation:

Once you have visually checked the new fittings and

connections, ensure that all taps are closed except the

new mixer tap, which should be left open. Turn on the

water supply at the mains stop cock. As the system

starts to refill, check carefully for leaks. Once you are

fully satisfied that there are no leaks, turn on the water

heating.

Clean the tap to remove any marks created during

installation as instructed then replace the bag that has

been provided to protect the tap until it is ready for use.

Produkt Specifikationer

Mærke:	CDA
Kategori:	Vandhane
Model:	TL1CH

Har du brug for hjælp?

Hvis du har brug for hjælp til CDA TL1CH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vandhane CDA Manualer

15 Marts 2024

13 Januar 2024

10 December 2023

7 Oktober 2023

13 August 2023

29 Maj 2023

10 Maj 2023

31 Marts 2023

3 Februar 2023

7 Januar 2023

Vandhane Manualer

Nyeste Vandhane Manualer

Oras 185 Manual

29 Juli 2025

Ikea DALSKÄR 806.082.78 Manual

27 Juli 2025

Ikea ÄLMAREN 006.035.00 Manual

27 Juli 2025

Ikea DALSKÄR 706.034.98 Manual

27 Juli 2025

Ikea ÄLMAREN 806.082.83 Manual

27 Juli 2025

Ikea ÄLMAREN 406.082.80 Manual

27 Juli 2025

Ikea ÄLMAREN 206.082.81 Manual

27 Juli 2025

Ikea ÄLMAREN 606.082.84 Manual

27 Juli 2025

Livarno Lux IAN 373821 Manual

25 Juli 2025

Biltema 86-5510 Manual

25 Juli 2025