CDN PT2 Manual

CDN Ikke kategoriseret PT2

Læs gratis den danske manual til CDN PT2 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om CDN PT2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Features

• 4 channels

• Programmable

• Dual function

• Memory

• Counts up & down in 4 channels separately

or simultaneously

• Clock

• Stopwatch

• Loud and long alarm

• Individual channel sounds

• Stop and restart

• Counts up after zero

• Food-safe ABS plastic

• Sliding mode switch

• 4-way mounting: pocket clip/magnet/stand/loop

• Battery and instructions included

Note: Remove sticker from display before use.

Note: In the following instructions, names of the

control buttons are shown in CAPS. Function

information that appears on the display is shown in

BOLD CAPS.

Battery Installation

Replace battery when LCD becomes dim or alarm level

declines.

1. Remove battery door by turning it counterclockwise.

2. Install a 1.5 V button battery with positive (+)

side up.

3. Replace battery door and lock it by turning

it clockwise.

Operating Instructions

A. Set Clock

1. Select CLOCK mode with sliding mode

switch. will appear after 12:0000 AM

inserting battery.

2. Press and hold ENTER approximately 2 seconds

until the display ashes.

3. Press HR, MIN and SEC to enter the desired

time. Press and hold button for fast advance.

4. Press ENTER to exit. The PT2 will automatically

exit 3 seconds after the last entry.

B. Count Down

1. Select COUNT DOWN mode with sliding

mode switch. COUNT DOWN will

appear on the display.

2. Press HR, MIN and/or SEC to enter the desired

time. Press and hold button for fast advance.

3. Press START/STOP to start the count down.

Press START/STOP button to interrupt the count.

Press START/STOP button again to resume the

count.

4. When the desired time is reached,

alarm will sound and the timer will

start to count up the “overtime”. (OverTime) OT

and COUNT UP will appear on the display while

TIME’S UP ashes.

5. Press START/STOP to stop the alarm.

The alarm will stop automatically after

60 seconds while the count up continues.

6. Press CLEAR to reset to . 0:0000

Note: The timer will retain any time showing on the

display when the sliding mode switch is moved to

another position.

Model: PT2

4-Event Timer & Clock

Counts 100 hours by minutes & seconds

C. Count Up

1. Select COUNT UP mode with sliding

mode switch. COUNT UP will appear on

the display.

2. Press START/STOP to start the count up.

If desired, the PT2 can count up from any desired

time by entering that time with the HR, MIN and

SEC buttons.

3. Press START/STOP button to interrupt the count.

Press START/STOP button again to resume

the count.

4. Press CLEAR to reset to .0:0000

5. The PT2 will count up to 99 hours,

59 minutes, and 59 seconds and stop

at , at which time an alarm will sound and 0:0000

TIME’S UP will ash for 60 seconds. Press any

button to stop alarm.

Note: The timer will retain any time showing on the

display when the sliding mode switch is moved to

another position.

D. Programming 4 Events

This device allows 4 different count down timer

settings temporarily or programmed into memory

(T1, T2, T3 and T4) with respective alarm beeping

sequences:

T1: BEEP in 1 second

T2: BEEP BEEP in 1 second

T3: BEEP BEEP BEEP in 1 second

T4: BEEP BEEP BEEP BEEP in 1 second

1. Count Down

a. Select PROGRAM TIMER mode with

sliding mode switch. and T1 COUNT

DOWN will appear on the display.

b. Press T1 to enter Timer 1 set mode. on the T1

display will be steady. If a time had previously

been entered in T1, it will appear on the

display. To enter a new time press CLEAR.

If a pre-set time had been entered into T1

memory, press CLEAR and then press ENTER

to clear memory.

c. Press HR, MIN and/or SEC to enter the desired

time. The edited time setting will remain there

as long as the counting cycle is not started/

completed and user may switch to other

operations.

d. To store time in memory, press ENTER after

entering the desired time. Memory is required

for simultaneous counting.

Note: Any time already in memory will be deleted

when the new time is entered into memory.

e. Press START/STOP to start counting down.

The count may be interrupted by pressing

START/STOP. To resume the count press

START/STOP again.

f. When the desired time is reached, alarm will

sound and will ash on the display.TIME’S UP

g. Press any button to stop the alarm and reset

to 0:0000.

h. Repeat steps b g through for T2, T3 and T4.

2. Count Up

T1, T2, T3 & T4 can be used as count up timers

starting from .0:0000

a. Press START/STOP to start counting

up or to pause and resume count.

b. The PT2 will count up to 99 hours, 59 minutes,

and 59 seconds and stop at , at which 0:0000

time an alarm will sound and TIME’S UP will

ash for 60 seconds. Press START/STOP to

stop alarm.

Note: The timer will retain any time showing on the

display when the sliding mode switch is moved to

another position.

3. 4-Event Simultaneous Operation

T1, T2, T3 & T4 can be used

simultaneously. The for T-number

the channel selected will be steady while other

channels counting will be ashing.

a. To activate T1, T2, T3 & T4 simultaneously,

hold ENTER and press START/STOP. Timers

will start counting down from the pre-set times

stored in their respective memory or count up

if there is no stored setting.

b. If two or more channels reach zero at the

same time, the channel with the lowest

T-number will sound rst and then the other

channels will sound in descending order.

For example, if T1, T2 and T4 reach zero

simultaneously, T1 will sound rst, then T2,

followed by T4.

c. Press any button to stop alarm.

d. To stop activated timers simultaneously, hold

ENTER and press START/STOP (even though

they were activated individually).

Note: Remove sticker from display before use.

Produkt Specifikationer

Mærke:	CDN
Kategori:	Ikke kategoriseret
Model:	PT2

Har du brug for hjælp?

Hvis du har brug for hjælp til CDN PT2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CDN Manualer

17 Juni 2025

15 Juni 2025

15 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

13 Juni 2025

13 Juni 2025

13 Juni 2025

13 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025