Chamberlain CWPIRC Manual

Chamberlain Bevægelsesdetektor CWPIRC

Læs gratis den danske manual til Chamberlain CWPIRC (4 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Chamberlain CWPIRC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Attach Motion Sensor box to

mounting plate with large silver

screw. Tighten screw until

Motion Sensor stays in place

when repositioned.

Motion Sensor

Swivel Bushing

Mounting PlateSun/Rain Shield

Carton Inventory

Assembly and Programming

Install 4 AA Alkaline batteries.

(Lithium batteries recommended

for colder environments.)

LED light will ﬂ ash.

Antenna

OFF

1 2

SWITCH SETTINGS

Switch #1 Switch #2

Learn

Button

OFF Low Sensitivity

ON High Sensitivity (Default)

NOTE: To avoid detection of small animals

move Switch #2 to OFF.

Motion Sensor

SWITCH #1:

SWITCH #2:

A Ensure Base Station and

Motion Sensor are in close

proximity to each other. Press

and release Learn Button

on Base Station. Buzzer will

sound.

B Within 60 seconds, press the

Learn Button on the inside of

the Motion Sensor. LED light

will illuminate and Base Station

will buzz.

3Learn Button

Test Motion Sensor by waving

hand in front of sensor. LED light

should ﬂ ash and the Base Station

will buzz X number of times

indicating which sensor has been

activated.

Insert battery pack facing away

from circuit board and fasten

cover with the smallest screws

(provided).

NOTE: Ensure the batteries do

not touch the circuit board and

the antenna and battery wires are

not pinched.

Overview

Learn Button

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth

defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

WIRELESS MOTION ALERT

ADD-ON SENSOR

MODELS CWPIR AND CWPIRC

The Wireless Alert Sensor is a Passive Infra-Red Motion Sensor that detects movement of people and vehicles. Each sensor has its own unique

ID, for a secure radio link. The base station (not provided) can learn the signals of up to 8 sensors. The base station gives a single beep for the

ﬁ rst sensor that is programmed, a double beep for the second, and so on. Additionally, multiple base stations can work with the same sensor to

sound in different places.

OFF 15 Feet (4.5 m) Detection Range

30 Feet (9.1 m) Detection Range

(Default)

MOTION SENSOR INSTALLATION

Mount Motion Sensor

horizontally on solid surface 3-5

feet (1-1.5 m) off the ground and

within 1/2 mile (0.8 km) of Base

Station (rotate sensor to access

screw holes). Unit should be able

to swivel as needed.

Attach sun/rain shield.

NOTE: Keep Motion Sensor

antenna away from metal

objects. Do not mount Motion

Sensor in direct sunlight, near

moving tree branches, or in the

path of a sprinkler system.

4 feet (1.2 m)

10-20 feet (3-6 m)

Vehicle Alert Installation: For cars, the best mounting position is

about 4 feet (1.2 m) high, between 10-20 feet (3-6 m)back, and

angled to see the back of car after passing the sensor.

The Motion Sensor lights up, but the Base Station does not

respond.

The Motion Sensor must be programmed to Base Station (See Step

3). Ensure Base Station is on and the volume is turned up.

Motion Sensor is detecting motion only part of the time.

Ensure the Motion Sensor is set to the High Sensitivity setting (See

Step 2). To detect cars, it is best to mount Motion Sensor at height

of car’s motor and have it between 10-20 feet (3-6 m) from the

road. Swivel sensor as needed.

The Wireless Motion Alert Sensor is giving false alarms.

Check for moving tree branches or insects in sensor window.

Motion Sensor can also be triggered by light shining directly in

sensor window, such as reﬂ ected sunlight, or motion in front of a

light source.

It is possible that condensation has built up on the sensor. Wipe

condensation from Motion Sensor with cotton swab. Let it sit

inside for a few hours, open to the air, without the batteries and it

should correct itself.

Check Sensor Switches on Motion Sensor. See Switch Settings.

Base Station beeps every 30 minutes.

The batteries in the Base Station or the Motion Sensor(s) are low.

Replace the 4 AA batteries. Check the Motion Sensor(s), if the LED

illuminates on all of the Motion Sensors, change the batteries in the

Base Station.

The Wireless Motion Alert Sensor is not getting expected

transmission range.

Keep both antennas vertical and keep Motion Sensor antenna away

from trees and metal objects. Ensure Base Station is in clearest

possible sight of the Motion Sensor. The less objects between the

devices, the longer the range.

NOTE: The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modiﬁ cations to this

equipment. Changes or modiﬁ cations not expressly approved by

the manufacturer could void the user’s authority to operate the

equipment.

Troubleshooting

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired

operation.

Any changes or modiﬁ cations not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/

bystanders and device.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Installation

Produkt Specifikationer

Mærke:	Chamberlain
Kategori:	Bevægelsesdetektor
Model:	CWPIRC

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain CWPIRC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Chamberlain Manualer

Chamberlain CWPIRC Manual

30 Juli 2024

Chamberlain CWPIR Manual

30 August 2023

Chamberlain CWA2000 Manual

1 Juni 2023

Chamberlain CWA2000C Manual

19 November 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Hikvision DS-TDSB00-EKH Manual

28 Juli 2025

Blaupunkt IR-S1 Manual

28 Juli 2025

Panasonic ST4 Manual

25 Juli 2025

Steinel L 331 S Manual

25 Juli 2025

Steinel MD-8 ECO COM1 Manual

25 Juli 2025

Steinel PD-24 ECO COM1 Manual

25 Juli 2025

Steinel IS 3360 COM1 Manual

25 Juli 2025

Steinel PD-8 ECO COM1 Manual

25 Juli 2025

Steinel IS 3180 COM1 Manual

25 Juli 2025

Vimar 19485.M Manual

24 Juli 2025