Chimera OctaPlus 5 Manual

Chimera Ikke kategoriseret OctaPlus 5

Læs gratis den danske manual til Chimera OctaPlus 5 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Chimera OctaPlus 5, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Lightbank Assembly for the

OctaPlus 3™ and

OctaPlus5™

Insert Poles into Pole Sleeves- Insert rounded

pole-ends into pole sleeves

located in inside “corners” of

the OctaPlus™ Lightbank.

Guide each pole carefully

through the pole sleeve until it

is snug at the opposite end of

the sleeve. Note: On the

OctaPlus 5™, the adaptor tips for the OctaPlus

57™ will push through the

grommet hole and be exposed

(see details on next page).

Mount Your OctaPlus™ Ring on the Stand – We strongly recommend that a stand adapter

(CHIMERA® model #3770) be used with the OctaPlus 5 and 57™ Lightbanks so that the weight is

not supported by the lighting instrument. A stand adapter, while helpful, is not essential for the

OctaPlus 3™ Lightbank. Mount your Speed Ring to the light stand using the 3770 stand adaptor or

the mounting method of your choice. For your safety and the security of your lighting instrument, if

at all possible, mount your lighting instrument to the OctaPlus™ Ring after mounting the assembled

OctaPlus™ Lightbank on the stand.

Erect the OctaPlus™ on the OctaPlus™ Ring- Start with one of upper holes; insert

exposed pole-end extending from Lightbank into hole on outside edge of Speed Ring. Pole

ends must be seated fully in bottom of holes. Repeat the pole insertion until all the poles are in

place. Many users feel it is easiest to insert the poles directly opposite each other. This helps

even out the tension on the OctaPlus™ Lightbank as it is assembled.

Install the Baffle and Front Screen – The interior baffle is attached to the inside of the

OctaPlus™ Lightbank just in front of the lighting instrument. Attach one of the Velcro® tabs on

the baffle to one of the Velcro® tabs on the pole sleeves. The next

attachment should be made directly opposite the first. Continue with the

attachment of the tabs working in this opposite attachment method until all

eight tabs are installed. Working in this method will assure a much tighter

fitting baffle for more even light distribution. Reposition the tabs, if

necessary, to make sure the baffle is centered in the OctaPlus™ Lightbank.

When installing the front screen, the CHIMERA® label should be facing

the outside. Take one of the eight sides of the front screen and line the

“back” edge of the Velcro® hook up with the back edge of the Velcro®

pile strip just inside the front of the OctaPlus™ Lightbank. Press the

two strips together and then move to the next edge of the front screen

and line it up the same way. Continue attaching the edges in a circular

fashion around the Lightbank. Keep the front screen as taut and smooth as possible for the

best possible light distribution.

Removing OctaPlus™ from the OctaPlus™ Ring - - Allow the light to cool completely

before removing the OctaPlus™ Lightbank. For longest life, remove the front screen and baffle

from the OctaPlus™ Lightbank and fold them neatly. Starting with one of the poles, grasp pole

in palm of hand and place thumb on the OctaPlus™ Ring. Grip the pole on opposite side with

your other hand for additional leverage. Apply backward pressure on pole to center it in its

mounting hole and slide to pole out of the hole. Repeat until all poles are free.

OctaPlus™ Lightbank Care and Use Instructions

Folding and Storing the OctaPlus™ Lightbank - Once the OctaPlus™ Lightbank is removed from

the OctaPlus™ Ring, fold it flat then fold it over again. Roll the Lightbank into a tight cylinder and place it in

the storage sack along with the other components. You may choose to leave the poles in place in the

OctaPlus™ Lightbank. If you are storing the OctaPlus™ Lightbank for a greater length of time it is better to

remove the poles. Make sure your CHIMERA® OctaPlus™ Lightbank is not wet, damp or soiled

before storing.

CHIMERA® OctaPlus 57™ Care and Use Instructions

Adding the OctaPlus 57™ Extension Kit – Assemble the OctaPlus 5™

Lightbank according to the instructions above (with or without the front screen

depending on the diffusion preferred). Then begin the OctaPlus 57™ assembly

by slipping the OctaPlus 57™ extension poles into the extension skirt pole

sleeves. Make sure the end with the rounded tip is in front.

Once all of the poles are in their sleeves, fit the rear end of the

OctaPlus 57™ extension poles over the adapter tips of the

OctaPlus 5™ poles protruding through the grommet holes. It

is easiest to start at the top of the OctaPlus™ Lightbank and

work your way to the bottom, moving back and forth as you

go. Once the poles are assembled, press the Velcro® strips between the OctaPlus 5™

and OctaPlus 57™ skirt together to seal the OctaPlus 57™ Lightbank into one unit.

Then, seal the Velcro® straps at each extension pole intersection.

Next, add the OctaPlus 57™ front screen using the front screen instructions above. Most of the time users

remove and store the OctaPlus 5™ front screen; however there may be times when you prefer to use the

OctaPlus 5™ front screen in combination with the OctaPlus 57™ front screen for an extra soft light.

CAUTION NOTES:

This is a professional product for use in moderate temperature environments. Failure to

follow these safety precautions could create a hazardous condition.

• Do not leave Lightbank unattended while in use.

• Open top and bottom flaps completely to allow air flow.

• Excessive heat and/or moisture may damage Lightbank.

• Do not use Lightbank in wet conditions.

• Always use light fixture’s protective screen. Screen must be of fine mesh size to prevent hot shards of

glass or quartz from contacting Lightbank in event of bulb explosion. Damage or fire caused by

exploding bulb is not covered by CHIMERA® warranty.

Please visit the CHIMERA® web site, www.chimeralighting.com, for additional care, use and repair

information.

CHIMERA

CHIMERACHIMERA® 1812 VALTEC LANE, BOULDER, COLORADO 80301 USA

TOLL FREE 888-444-1812 PHONE 303-444-8000 FAX 303-444-8303

EMAIL: salesinfo@chimeralighting.com WEB SITE: www.chimeralighting.com

Produkt Specifikationer

Mærke:	Chimera
Kategori:	Ikke kategoriseret
Model:	OctaPlus 5

Har du brug for hjælp?

Hvis du har brug for hjælp til Chimera OctaPlus 5 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Chimera Manualer

Chimera OctaPlus 5 Manual

11 December 2024

Chimera OctaPlus 57 Manual

10 December 2024

Chimera OctaPlus 3 Manual

10 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MSW -AIRS1290ASN Manual

17 August 2025

Mueller SC 98.47 pro Manual

17 August 2025

MSW -WPW-20 Manual

17 August 2025

Planet WGS-4215-8P2X Manual

17 August 2025

Mueller SC 98.40 knx Manual

17 August 2025

MSW -MS76A Manual

17 August 2025

MSW -HFCV-40-C Manual

17 August 2025

Mars Gaming MCPU-XU9 Manual

17 August 2025

Mars Gaming MPS5-B Manual

17 August 2025

B-Tech BT8566 Manual

17 August 2025